PHILIPS DDL200 Wireless keypad User Manual
- June 1, 2024
- Philips
Table of Contents
PHILIPS DDL200 Wireless keypad
Warnings & Safety Information
Safety
- Before using this product, please read and understand all instructions. Damage caused by failure to follow instructions is not covered by the warranty.
- Only use components provided by the manufacturer and suggested accessories.
- Only use new, non-rechargeable AAA Alkaline batteries.
- Do not forcibly disassemble the product to trigger an alarm or damage the product.
- Do not remove the batteries during lock setup and operation.
Caution
- Do not place the batteries near fire sources.
- Do not connect the 2 poles of the batteries to metals in order to avoid a short circuit and potential explosion.
- Any replacement component should be performed by Philips, a Philips-authorized service center or professional technician.
- Do not use parts or accessories manufactured by others, except batteries.
Returns & Disposal
- Product can be returned at authorized Philips service centers. Appropriate compensation will be provided if the returned product meets Philips conditions.
- Please follow local regulations and do not throw used product or batteries into normal household waste.
Product Introduction
DDL200 is a Bluetooth device as an accessory of the retrofit lock
DDL230X to verify PIN codes and fingerprints, the device is powered by 2 AAA
batteries (included).
Definition
- Pairing Mode: Press and hold the “X” button for 5 seconds, until the green light blinks slowly, and the buzzer beeps shortly one time.
- One-Touch Locking: Press and hold any key on keypad for 2 seconds to lock the door.
- Wrong Entry Limit: After 10 unsuccessful attempts to enter a PIN code or 5 unsuccessful attempts to enter a fingerprint, the keypad will shut down and be unusable for 3 minutes.
Installation
Packing List
- Keypad
- 2 AAA Batteries
- 2 Mounting Screws (optional)
- 2 Wall Anchors
- Adhesive Mounting Strip
- User Manual
- Security Screw
Installation Steps
Attention
The keypad should be installed within 118″ (3 meters) far from the door.
- Take off the release paper of the adhesive mounting strip.
- Stick or screw it on a clean surface, such as door frame and so on.
Attention
You have the option to omit drilling the back panel into the wall, and only
use the adhesive to install your keypad on the door frame.
If you are drilling into the wall, please follow next steps.
-
A. According to the wall surface, select installation type (optional).
-
B. Drill the holes (optional).
- Take one of the included mounting screws and poke it through the center of each of the two hole on the mounting plate. Mark the holes with a pen, and drill holes in the two spots you marked.
- *Insert anchors into wall. (optional)
If required for your surface, take two of the anchors included with your wireless keypad and gently tap them into the drilled holes using a hammer.
-
C. Screw mounting plate into the wall.
-
D. Remove the battery tab.
While holding the batteries in place, remove the plastic battery isolation tab. -
E. Align the slots of the keypad with the hooks of the mounting plate and slide the keypad down.
-
F. Fix the keypad with security screw.
Pair the Keypad
-
Download the Philips Home Access App from Google Play or App Store.
-
Add the DDL230X retrofit smart lock in the Philips Home Access App.
Attention- Make sure the Philips Home Access App has been downloaded and installed.
- Pair the DDL230X retrofit lock with your phone prior to keypad pairing.
-
Press and hold “x” button on the keypad for 5s to enable pairing mode. Pairing mode expires in 300 seconds.
-
Select the lock you want to pair with, then go to “Device settings” → Accessory → Add accessories.
-
Follow instructions on the App to complete the pairing process.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Warranty
2 years warranty
For more information on the warranty applicable for this product, please visit
www.philips.com or contact the dealer where you
purchased the product.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of Shenzhen Conex Intelligent Technology Co., Ltd. and Shenzhen Conex Intelligent Technology Co., Ltd. is the warrantor concerning this product.
Sign your product up and get support at: www.philips.com/support
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>