SEALEY SSP142.V4 Tig Welding Gauntlets Pair Instruction Manual
- June 1, 2024
- SEALEY
Table of Contents
SEALEY SSP142.V4 Tig Welding Gauntlets Pair
Thank you
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
REFER TO
INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR
THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE
FOR FUTURE USE.
INTRODUCTION
12477:2001. Size range: 9,10, 11.
Notified Body: ITS Testing Services (UK) Limited, Ventre Court, Meridian
Business Park, Leicester, LE19 1WD
Type Examination Certificate Number: LEC FI00339435
Approved Body No: 0362
SAFETY
✔ For multilayer gloves that can be separated, the performance of levels are
only applicable to the whole glove including all layers.
✖ DO NOT use where there is risk of entanglement by moving parts.
✔ When gloves are intended for arc welding: these gloves do not provide
protection against electric shock caused by defective or live working
equipment. Note that electrical resistance is reduced if the gloves are wet,
dirty or soaked with sweat. This could increase the risk of electric shock.
✔ Protection is only given to the palm of the hand, the cuff will give
adequate protection against small splashes of molten metal.
✔ There are substances in the glove which are known to cause allergies. A list
of raw substances is available upon request.
✔ Type B gloves are recommend when high dexterity is required, as for TIG
welding. Type A gloves are recommended for other welding processes.
✔ There is no standardized test method at present for detecting UV penetration
of materials for gloves, but the current methods of construction of protective
gloves for welders do not normally allow penetration of UV radiation.
PERFORMANCE
Mechanical Risks
| Abrasion Resistance| 1| (on 4 maxi)| The numbers indicate the performance level of the gloves. 1 = lowest 4 = highest 5 = highest for blade cut resistance
X’ indicates that the glove has not been submitted to the test or the test method appears not to be suitable for the glove design or material.
---|---|---|---|---
Blade Cut Resistance| 1| (on 5 maxi)
Tear Resistance| 1| (on 4 maxi)
Puncture Resistance| 1| (on 4 maxi)
Cut Resistance Method (EN ISO 13997)| X| (A to F)
Thermal Risks (Heat/Flame)
| Limited Flame Spread|
4|
Contact Heat| 1
Convective Heat| 2
Radiant Heat| X
Small drops of molten metal| 4
Large drops of molten metal (if applicable)| X
Protective Gloves for Welders
| Burning Behaviour| B| | Suitable for high dexterity tasks.
Contact Heat| B
Small splashes of molten metal| B
INSTRUCTIONS FOR USE
- Place glove over hand fitting the thumb and fingers in the appropriate positions, making sure the glove is fitted comfortably to carry out the task at hand.
- Remove by pulling the glove upward from the fingers.
MAINTENANCE
✖ DO NOT wash or tumble dry.
✔ The packaging provided with the glove is suitable for the required
transport.
✔ This product does not have an expiry date, but should be replaced when
worn/damaged.
This document has been drawn up according to Regulation (EU) 2016/425 as amended to apply to GB for Personal Protective Equipment. The declaration of conformity can be accessed at www.sealey.co.uk.
ENVIRONMENT
PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk
or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
REGISTER YOUR PURCHASE HERE
CUSTOMER SUPPORT
EU | Sealey EU Ltd, Farney Street, Carrickmacross, Co. Monaghan, A81 PK68
Ireland
UK | Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds,
Suffolk. IP32 7AR
01284 757500
sales@sealey.co.uk
www.sealey.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>