SEALEY 9139L Anti Cut PU Gloves Instruction Manual
- June 1, 2024
- SEALEY
Table of Contents
SEALEY 9139L Anti-Cut PU Gloves
Specifications
- Product: Anti-Cut PU Gloves (Cut Level C Large/Extra Large) – Pair
- Model No: 9139L 9139XL
- Cut Resistance Level: C
- CE Marked and conforms to BS EN 388:2016 4-4-4-3-C
- Notified Body No: 0075
- Certificate Number: 0075/1022/162/10/18/2340
Product Usage Instructions
1. Introduction
Highest cut resistance – (Cut Level C) provides maximum protection against cuts and abrasions. Polyurethane-coated palm for improved grip. The whole liner is cut resistant, including the back of the glove.
2. Safety
- Ensure the glove is suitable for the task at hand.
- Before use, visually inspect the glove for any signs of\ deterioration such as abrasion, cut, tear, or puncture. Discard if damaged.
- Do not wear these gloves when there is a risk of entanglement by moving parts of machines.
- For multilayer gloves, performance levels apply to the entire glove, including all layers.
3. Performance
The glove performance levels are as follows:
- Mechanical Hazard Abrasion Resistance: 4
- Blade Cut Resistance: 4
- Tear Resistance: 4
- Puncture Resistance: 3
- Cut Resistance Level: C
4. Instructions for Use
- Place glove over hand fitting the thumb and fingers in the appropriate positions comfortably for the task.
- To remove, pull the glove upward from the fingers.
5. Maintenance
- The packaging provided is suitable for transport.
- Inspect gloves for damage before each use. Replace if worn or damaged.
6. Storage
The design performance is not significantly affected by aging when stored in appropriate conditions (humidity, temperature, clean, ventilated, light).
FAQ
- Q: How often should I replace these gloves?
- A: Inspect the gloves for damage before each use. Replace them if you notice any signs of wear or damage to ensure optimal protection.
- Q: Can these gloves be used for handling sharp objects?
- A: Yes, these gloves provide high cut resistance (Cut Level C) and are suitable for handling sharp objects while following safety guidelines and instructions.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
REFER TO INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
INTRODUCTION
The highest cut resistance – (Cut Level C) provides maximum protection against cuts and abrasions. Polyurethane-coated palm for improved grip. The whole liner is cut-resistant, including the back of the glove. CE Marked and conforms to BS EN 388:2016 4-4-4-3-C.
- Notified body No: 0075
- Certificate number: 0075/1022/162/10/18/2340
- Carried out by CTC Groupe
SAFETY
- Ensure the glove is suitable for the task at hand.
- Before use, the glove shall be visually controlled. In case of deterioration, the gloves must be scrapped (abrasion, cut, tear, puncture).
- DO NOT wear these gloves when there is a risk of entanglement by moving parts of machines.
- For multilayer gloves that can be separated, the performance levels are only applicable to the whole glove, including all layers.
The numbers indicate the performance level of the glove. 1 = lowest 4 = highest 5 highest for blade cut resistance
PERFORMANCE
INSTRUCTIONS FOR USE
- Place glove over hand fitting the thumb and fingers in the appropriate positions making sure the glove is fitted comfortably to carry out the task at hand.
- Remove by pulling the glove upward from the fingers.
MAINTENANCE
- The packaging provided with the glove is suitable for transport.
- Inspect gloves for damage before wearing them. Replace the gloves if worn or damaged.
STORAGE
The design performance is not significantly affected by aging when stored in appropriate conditions (humidity, temperature, clean, ventilated, light).
This document has been drawn up according to Regulation (EU) 2016/425 as amended to apply to GB for Personal Protective Equipment. The declaration of conformity can be accessed at www.sealey.co.uk.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations
- Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
- Important: No Liability is accepted for incorrect use of this product.
- Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim
EU | Sealey EU Ltd, Farney Street, Carrickmacross, Co. Monaghan, A81 PK68
Ireland
UK | Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds,
Suffolk. IP32 7AR
- 01284 757500
- sales@sealey.co.uk
- www.sealey.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>