SEALEY AK2933.V2 Premier Electronic Micro Soldering Torch Instruction Manual

: June 1, 2024
: SEALEY

Table of Contents

SEALEY AK2933.V2 Premier Electronic Micro Soldering Torch
Product Information
Product Usage Instructions
SAFETY
INTRODUCTION
OPERATION
ENVIRONMENT PROTECTION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SEALEY AK2933.V2 Premier Electronic Micro Soldering Torch

Product Information

Specifications

Brand: Sealey
Model: AK2933.V2
Type : Electronic Micro Soldering Torch
Issue Date : 11/01/24

Product Usage Instructions

Safety Guidelines

It is crucial to follow these safety guidelines for the safe operation of the soldering torch:

```
* Always wear approved eye and face protection when using the torch.
```
- Do not use the torch if damaged or if there is a gas leak.
- Handle butane gas with extreme care as it is highly flammable.
- Point the torch away from eyes and body during ignition and operation.

Operational Instructions

Follow these steps to operate the soldering torch:

1. Ensure the torch is in a well-ventilated area before igniting.

Use the trigger to ignite the torch flame.
Adjust the flame size using the control mechanism.

Maintenance and Storage

Proper maintenance and storage are essential for the longevity of the soldering torch:

```
* Allow the torch to cool after each use before storing it.
```
- Store the torch in a safe, dry, childproof location away from direct sunlight when not in use.

FAQ

Q: Can children operate the soldering torch?
- A : No, children should not operate the torch. It should be handled by adults only.
Q: How should I dispose of the product when it becomes unserviceable?
- A : Drain any fluids into approved containers and dispose of the product according to local regulations. Recycle unwanted material whenever possible.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Refer to the instruction manual

Wear eye protection

Warning hot surface

Warning flammable material

SAFETY

WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment, make sure you know where the nearest fire extinguisher is.
WARNING! Always wear approved eye/face protection when operating the torch.
WARNING! DO NOT use the torch if you notice it is damaged or if there could be a gas leak from it.
WARNING! Butane gas is extremely flammable, handled with care.
WARNING! Always point the torch away from the eyes and body when igniting and during operation.
WARNING! DO NOT put the torch down when it is lit, DO NOT leave it unattended.
WARNING! The flame is not easily visible in bright daylight.
WARNING! Ensure the flame is completely extinguished after use. DO NOT use water to cool the torch down.
WARNING! Only use in a well-ventilated area.
DO NOT use the torch in an area where paint fumes, solvents or other flammable solids, liquids or gases pose a potential hazard. Keep flammable material away from the torch when operating.
DO NOT operate the torch when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT hold any workpiece by hand.
DO NOT touch the workpiece close to the heated area as it will be very hot. Allow to cool.
DO NOT operate the torch if it is damaged as this may cause failure and/or possible personal injury.
DO NOT touch the tip of the torch during or immediately after use, as it will be very hot. Allow to cool.
DO NOT allow children to operate the torch.
After use allow the torch to cool before storing it.
When not in use, store away from direct sunlight in a safe, dry, childproof location.
DO NOT store at over 40°C, such as in a car in hot weather.

INTRODUCTION

Piezoelectric ignition with 1300°C burner flame adjustable from 12 to 35mm. Fitted with a safety lock and continuous-use switch for easy operation. Standard fill gives approximately 30 minutes of continuous operation. Powered by Butane (lighter fuel).

OPERATION

SEALEY-AK2933.V2-Premier-Electronic-Micro-Soldering-Torch-
fig5

FILLING (Refer to fig.1)

Use standard butane fuel. Fill in a well-ventilated area away from open flame. Turn the torch off, make sure the flame is extinguished, and allow to cool down for five minutes before filling.
Hold the torch upside down and insert the filling can’s nozzle into the gas filling valve. Press the nozzle into the valve and release the gas. Once gas begins to seep out around the edge of the nozzle, the gas tank is full. Remove the filling can.
OPERATION (Refer to fig.1)
Slide safety lockdown.
Press the trigger to ignite, and release the trigger to extinguish the flame.
Slide the trigger lock up after ignition to keep a continuous burning flame, without holding down the trigger. Slide the lockdown to extinguish the flame.
Move flame size control (fig.2) to vary flame strength, + to increase, – to decrease.

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling center and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on technical@sealey.co.uk or 01284 757505.

Important: No Liability is accepted for incorrect use of this product.
Warranty: The guarantee is 12 months from the purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR