SEALEY AK7160 Bridge Bearing Puller Set Instruction Manual
- June 1, 2024
- SEALEY
Table of Contents
10PC BRIDGE BEARING PULLER SET
MODEL NO: AK7160
AK7160 Bridge Bearing Puller Set
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR
THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE
FOR FUTURE USE.
SAFETY
- WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this tool.
- WARNING! Familiarise yourself with the specific applications and limitations of the kit, as well as any potential hazards.
- This kit should be used in conjunction with inspection maintenance procedures recommended in the vehicle manufacturer’s manual.
- Ensure that the kit is correct for the task.
- Wear the appropriate personal protective equipment for the task. A full range is available from your Sealey stockist.
- DO NOT use the kit for any purpose other than that for which it is designed.
- Ensure that the vehicle is properly supported with axle stands before working under the vehicle.
- Ensure there is adequate lighting prior to using the kit. A range of inspection lamps are available from your Sealey stockist.
- Keep children and unauthorised persons away from the working area.
- DO NOT use the kit if any parts are damaged or missing, as this may cause failure and/or personal injury.
- DO NOT use the kit when you are tired, or under the influence of alcohol, drugs or intoxicating medication.
- After use, store in a safe, dry childproof area.
INTRODUCTION
Screw-type bridge extractor set. The thin tapered lips on the collets secure a positive grip on the curved surface of the internal bearing bore. Gently removes blind bearings where the use of a slide hammer may damage the surrounding material. Bearing extractor collets with internal capacity from 8 to 27mm.
SPECIFICATION
Model No:…………………………………………………. AK7160
Collet Diameter:…Ø8-9.4, 9.5-11.4, 11.5-13.4, 13.5-16.4, 16.5-18.4, 18.5-24,
24.5-27mm
CONTENTS
Refer to attached Parts List
OPERATION
5.1. Before using the required attachment disassemble and grease asshown in
fig.1. Collet to be fully inserted into the bearing before attempting to pull
the bearing.
5.2. Insert the attachment into the bearing.
5.3. Hold the attachment with a spanner and wind the drive pin into the
attachment, with another spanner, until the jaws open and grip thebearing,
fig.2.
5.4. Place the bridge extractor legs in the correct position over the bearing
housing, tighten the cap head screws screws on the legs tohold them in
position, fig.3.
5.5. Screw the bridge extractor’s hex screw into the attachment. Hold the
attachment with a spanner and tighten.
5.6. Hold the long cap head screw still and wind the bearing out using the nut
beneath, fig.3.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
https://qrco.de/bcy2E9
REGISTER YOUR PURCHASE HERE
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
sales@sealey.co.uk
www.sealey.co.uk
Original Language Version
© Jack Sealey Limited
AK7160 Issue 2 (3,F) 19/09/23
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>