TAC 40-22300T Texture Black Pnc Side Step Installation Guide
- June 1, 2024
- TAC
Table of Contents
TAC 40-22300T Texture Black Pnc Side Step
Product Information
Product Specifications:
- Product Name: PNC Sidebar for 2018-2024 Jeep Wrangler JL 4DR
- Part Number: 40-22300T
- Material: Steel
- Finish: Texture Black
- Includes: Various mounting brackets, bolts, washers, and nuts
Product Usage Instructions
Installation Steps:
- Identify all parts from the parts list provided.
- Start with the passenger side installation following the provided diagrams.
- Use the specified bolts, washers, and nuts to securely attach the PNC Sidebar to the vehicle.
- Ensure all brackets are properly aligned and tightened to the correct torque specifications.
- After installation, wax the product to protect the finish. Regular waxing is recommended for maintenance.
Cleaning Instructions:
To clean the Sidebar, use mild soap and water. Do not use any polish or wax
with abrasives that could damage the finish.
Frequently Asked Questions (FAQ):
-
Q: Can this product be installed on a different vehicle model?
A: No, this PNC Sidebar is specifically designed for 2018-2024 Jeep Wrangler JL 4DR models. -
Q: How often should I wax the product after installation?
A: Regular waxing is recommended to maintain a protective layer over the finish. Depending on usage and environmental conditions, waxing every few months is advisable.
Parts List
1| Driver/left side PNC Sidebar| 2| Passenger/right side Center & Rear Support
Brackets
---|---|---|---
1| Passenger/right side PNC Sidebar| 6| 10-1.5mm x 30mm Hex Bolts
1| Driver/left side Front Mounting Bracket| 12| 10mm x 24mm x 2mm Flat Washers
1| Passenger/right side Front Mounting Bracket| 6| 10-1.5mm Nylon Lock Nuts
1| Driver/left side Center Mounting Bracket| 12| 8-1.25mm Combo Bolts
1| Passenger/right side Center Mounting Bracket| 6| 8-1.25mm x 35mm Hex Bolts
1| Driver/right side Rear Mounting Bracket| 6| 8mm x 28mm x 3mm Flat Washers
1| Passenger/right side Rear Bracket| 6| 8mm Lock Washers
1| Driver/left side Front Support Bracket| 12| 6-1.0mm x 25mm Hex Bolts
1| Passenger/right side Front Support Bracket| 24| 6mm x 22mm x 2mm Flat
Washers
2| Driver/left side Center and Rear Support Brackets| 12| 6-1.0mm Nylon Lock
Nuts
INSTALLATION PROCEDURE
-
REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. FACTORY-INSTALLED OR AFTERMARKET “ROCK RAILS,” SIDE STEPS, OR RUNNING BOARDS MUST BE REMOVED.
-
Start installation toward the front of the passenger side of the vehicle and find the front threaded insert located in between the first pair of holes along the pinch weld, (Figure 1).
-
Select the Passenger/right side Front Mounting Bracket, (Figure 2). IMPORTANT: Use the illustration above and Figure 3 to properly identify the Mounting Bracket. Attach the Bracket to the threaded insert using (1) 8mm Hex Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer, (Figure 3). Do not tighten the hardware at this time.
-
Next, select the Passenger/right side Front Support Bracket, (Figure 4).
IMPORTANT: Use the illustration above to help identify the correct Support Bracket. Align the Bracket to the back of the pinch weld and the rear side of the Front Mounting Bracket. Attach the Support Bracket to the pinch weld using (2) 6mm Hex Bolts, (4) 6mm Flat Washers, and (2) 6mm Nylon Lock Nuts, (Figures 4—6).
NOTE: Insert bolts from the outside of the pinch weld and through the Bracket. Use (1) 10mm Hex Bolt, (2) 10mm Flat Washers, and (1) 10mm Nylon Lock Nut to secure the Support Bracket to the Mounting Bracket, (Figures 5 & 6). Do not tighten the hardware at this time. -
Move along the body panel to the center mounting location and locate the threaded insert and pair of holes on the pinch weld, (Figure 7). Repeat Steps 3 & 4 to install the Center Brackets, (Figures 9 & 10). NOTE: The Center and Rear Mounting Brackets look similar but each one is unique. Notice the bottom corner trim on the Center Mounting Bracket in the illustration above and Figure 8.
-
Move to the last, rear, mounting location and locate the threaded insert and pair of holes on the pinch weld, (Figure 11). Repeat Steps 3 & 4 to install the Rear Brackets, (Figures 12 & 13). NOTE: The Center and Rear Mounting Brackets look similar but each one is unique. Notice the rounded corners on the Rear Mounting Bracket in the illustration above and Figure 8.
-
Select the Passenger/Right Sidebar. Use the illustration above to help identify the correct Sidebar for each side. Carefully position the Sidebar onto the (3) Mounting Brackets. IMPORTANT: Do not slide,(front to back or rotate), the Sidebar on the Brackets, or damage to the finish on the Sidebar may result. Attach the Sidebar to the Mounting Brackets with (6) 8mm x 25mm Combination Hex Bolts, (Figures 14—16). Do not tighten the hardware. NOTE: Mounting cradles on Brackets should be inline and pointing toward the rear of the vehicle for proper installation. Snug all hardware but do not tighten.
-
Level and adjust the Sidebar and tighten all hardware.
-
Repeat Steps 1—8 for driver/left Sidebar installation.
-
Do periodic inspections of the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installation. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Sidebar.
Passenger Side Installation Pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>