SEALEY SSP12.V4 Reflective Rigger’s Gloves Instruction Manual

SEALEY SSP12.V4 Reflective Rigger’s Gloves

Product Information

• Specifications
  • Model Numbers: SSP12.V4, SSP12/6, SSP13.V4, SSP13/6, SSP14HV, SSP14HV/6
  • Conforms to Standards: BS EN 21420:2020 and 388:2016 Level 2242X

Product Usage Instructions

• Introduction
  • Strong stitching, a generous fit, and quality materials make this an ideal glove for general-purpose trade use.
• Safety
  • Ensure the glove is suitable for the task at hand.
  • Before use, visually inspect the glove for any signs of deterioration such as abrasion, cut, tear, or puncture.
  • Do not wear these gloves when there is a risk of entanglement by moving parts of machines.
  • For multilayer gloves that can be separated, note that the performance levels apply to the whole glove including all layers.
• Performance
  • Mechanical Hazard EN 388:
  • Abrasion Resistance: 2
  • Blade Cut Resistance: 2
  • Tear Resistance: 4
  • Puncture Resistance: X (Not tested)
• Instructions for Use
  • Putting on the Gloves:
  • Place the glove over the hand fitting the thumb and fingers in the appropriate positions making sure the glove is fitted comfortably to carry out the task at hand.
  • Removing the Gloves:
  • Remove by pulling the glove upward from the fingers.
• Maintenance
  • Do not wash or tumble dry the gloves.
  • The packaging provided with the glove is suitable for transport.
  • Replace the gloves if worn or damaged.

FAQs

• Q: Can these gloves be washed?
  • A: No, it is advised not to wash or tumble dry the gloves. Replace them if they become worn or damaged.
• Q: What standards do these gloves conform to?
  • A: These gloves conform to BS EN 21420:2020 and 388:2016 Level 2242X standards for mechanical hazards.

REFER TO INSTRUCTIONS

IMPORTANT:

• PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
• USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
• FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

INTRODUCTION

• Strong stitching, a generous fit and quality materials make this an ideal glove for general-purpose trade use.
• Conforms to BS EN 21420:2020 and 388:2016 Level 2242X.

SAFETY

• Ensure the glove is suitable for the task at hand.
• Before use, the glove shall be visually controlled. In case of deterioration, the gloves must be scrapped (abrasion, cut, tear, puncture).
• DO NOT wear these gloves when there is a risk of entanglement by moving parts of machines.
• For multilayer gloves that can be separated, the performance levels are only applicable to the whole glove, including all layers.

PERFORMANCE

INSTRUCTIONS FOR USE

• Place the glove over the hand fitting the thumb and fingers in the appropriate positions making sure the glove is fitted comfortably to carry out the task at hand.
• Remove by pulling the glove upward from the fingers.

MAINTENANCE

• DO NOT wash or tumble dry.
• The packaging provided with the glove is suitable for transport.
• Replace the gloves if worn or damaged.
• This document has been drawn up according to Regulation (EU) 2016/425 as amended to apply to GB for Personal Protective Equipment.
• The declaration of conformity can be accessed at www.sealey.co.uk.

ENVIRONMENT PROTECTION

• Recycle unwanted materials instead of disposing of them as waste.
• All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner that is compatible with the environment.
• When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
• Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team at technical@sealey.co.uk or 01284 757505.
• Important: No Liability is accepted for incorrect use of this product.
• Warranty: The guarantee is 12 months from the purchase date, proof of which is required for any claim.

CONTACT

• Sealey Group,
• Kempson Way,
• Suffolk Business Park,
• Bury St Edmunds,
• Suffolk. IP32 7AR
• 01284 757500
• sales@sealey.co.uk.
• www.sealey.co.uk.
• © Jack Sealey Limited
• SSP12.V4 SSP12/6 SSP13.V4 SSP13/6 SSP14HV SSP14HV/6 Issue 1 23/11/23
• MODEL NO:
  • SSP12.V4 SSP12/6
  • SSP13.V4 SSP13/6
  • SSP14HV SSP14HV/6

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>