i-PRO WV-U35401-F2L Network Camera Installation Guide
- June 1, 2024
- i-PRO
Table of Contents
i-PRO WV-U35401-F2L Network Camera
About the user manuals
Product documentation is composed of the following documents.
- Installation Guide (this document): Provides information about “Precautions”, “Precautions for installation” and the installation method.
- Web Guide (Refer to the link on the following product information website): Includes installation videos, basic functions, and basic operation methods for this device.
- User manual (Refer to the link on the following product information website):
- This section describes the software operating instructions common to each model. https://i-pro.com/products_and_solutions/en/surveillance/documentation-database
< Control No.: C**>”** used in these documents should be used to search
for information on our technical information website
(https://i-pro.com/products_and_solutions/en/surveillance/learning-and-
support/knowledge-base/technical information) and will guide you to the right
information.
- Before attempting to connect or operate this product, please read these instructions carefully and save the Important Safety Instructions leaflet for future use.
- microSDXC/ microSDHC/ microSD memory card is described as a microSD memory card.
- The external appearance and other parts shown in this manual may differ from the actual product within the scope and will not interfere with normal use due to the improvement of the product.
Disposal of Old Equipment and Batteries
Only for the European Union and countries with recycling systems
These symbols on the products, packaging, and/or accompanying documents mean
that used electrical and electronic products and batteries must not be mixed
with general household waste. For proper treatment, recovery and recycling of
old products and used batteries, please take them to applicable collection
points by your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment. For more information about collection and recycling, please contact your local authority. Penalties may be applicable for incorrect disposal of this waste, by national legislation.
Note for the battery symbol (bottom symbol)
This symbol might be used in combination with a chemical symbol. In this case,
it complies with the requirement set by the Directive for the chemical
involved.
For U.S.A..
NOTE: This equipment has been tested and found to comply with the limits
for a Class A Digital device, under Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment- menu. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used by the instructions manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct
the interference- ence at his own expense.
For U.S.A.
The model number and serial number of this product may be found on the surface
of the unit. You should note the model number and serial number of this unit
in the space provided and retain this book as a permanent record of your
purchase to aid identification in the event of theft.
Model No.
Serial No.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Supplier’s Declaration of Conformity
Trade name: i-PRO
Model No. : W-U35401-F2L,
W-U35301-F2L,
Responsible Party: i-PRO Americas Inc.
8550 Fallbrook Drive, Suite 200 Houston, Texas 77064
Support Contact: 1-800-513-5417
For U.S.A.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
For Canada
CAN ICES-3(A)/NMB-3(A)
WARNING
Operation of this product in a residential environment could cause radio
interference.
Caution: Notice
- The DC power supply connected to the camera must be in the same building.
- The network camera is only intended for a connection to an ethernet or PoE network without routing to the outside plant.
- This product has no power switch. Be sure to install disconnect devices such as a circuit breaker to shut down the main power of power supplying equipment for this product.
- Before attempting to connect or operate this product, please read these instructions carefully.
- This product is not suitable for use in locations where children are likely to be present.
- Do not install this product in locations where ordinary persons can easily reach.
- This product is a professional equipment.
- For information about screws and other parts required for installation, refer to the corresponding section of this document.
Precautions
To prevent harm to people and property damage, it explains what must be
observed without fail. The safety statements common to all i-PRO network
camera models are posted on the website linked from the two-dimensional
barcode on the right. Please be sure to confirm it.
https://i-pro.com/products_and_solutions/en/surveillance/learningand-support
/knowledge-base/safety-instructions
- Do not install this product in a restricted or prohibited environment.
- Failure to observe this may result in injury, accident, or malfunction due to falling.
- Please check the safety precautions common to all models on the website above and the installation precautions in the Installation Guide.
- Refer installation work to the dealer.
- Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer.
- Install the product accurately and securely on an installation surface according to the installation instructions.
- Failure to observe this may cause injury or accidents.
- Take measures of protection against this product falling.
- Failure to observe this may cause a drop resulting in injury.
- Securely fix the product to the installation surface using screws or anchors. If the fall prevention wire is included, be sure to install it.
- Stop the operation immediately when something is wrong with this product.
- When smoke goes up from the product, the smell of smoke comes from the product, or the exterior of the product has deteriorated, continued use will cause a fire or fall of the product resulting in injury, or property damage.
- In this case, turn the power off immediately and contact qualified service personnel for service.
- Conduct periodic inspections.
- Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents.
- Consult the dealer for the inspections.
- Be sure to turn off the power before inspection or maintenance.
Precautions for installation
- i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.
- To prevent injury, the product must be securely mounted to an installation surface according to the Installation Guide.
- Installation area for this product
- Select an appropriate place for the installation area (such as a strong installation surface) in your particular environment.
- Make sure that the installation area is strong enough to hold this product, such as a concrete ceiling.
- Install the camera in the foundation area of the architecture or where sufficient strength is assured.
- Do not mount the product on a plasterboard or a wooden section because they are too weak. If theproduct is unavoidably mounted on such a section, the section shall be sufficiently reinforced.
- Install the product in areas that do not receive direct sunlight.
- Do not place this product in the following places
- Locations where a chemical agent is used such as a swimming pool
- Locations subject to moisture or ail smoke such as a kitchen
- Locations that have a specific environment that is subject to an inflammable atmosphere or solvents
- Locations where radiation, an X-ray, a strong radio wave or a strong magnetic field is generated
- Locations near coasts directly subjected to sea breezes, or locations subject to corrosive gases such as from hot springs, volcanic regions, etc.
- Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (This product is not designed for in-vehicle use.)
- Locations near rubber products containing sulphur (packing, rubber feet, etc.)
- Locations are subject to condensation as the result of severe temperature changes such as near the the outdoor unit of an air conditioner.
Screw tightening
- Do not use an impact driver. The use of an impact driver may damage the screws or cause tightening excessively.
- About reflection of light from outside or IR light
- A ghost may appear on the screen depending on the incident angle of external light.
- In the case of using the IR light, installation of a camera near a wall may cause reflection of infrared rays resulting in a part of the screen or the entire screen turning whitish.
- Refer to our technical information website «Control No.: CO109> for image examples and measures to take.
- Take notice of the humidity Install this product when the humidity is low. If the installation is performed when it is raining or in very humid conditions, the inside may be affected by humidity, causing a mist-over inside the dome cover.
- Protection from lightning When cables are used outdoors, there is a chance that they may be affected by lightning. In such a case, install a lightning arrestor close to the camera, and make the length of the network cable between the camera and lightning arrestor as short as possible to prevent the camera from being affected by lightning. Refer to our technical information website
- When noise disturbance may happen Noise may appear in video or audio near a strong electric field from a TV or radio antenna, motors and transformers, or a strong electric field/magnetic field from a power line (lamp line) of AC100 V or more. Conduct the power distribution work to keep 1 m (3.28 feet) away from them or conduct the electric conduit work using metal pipes. (Be sure to make the ground connection of the metal pipes.)
- Equipment classification and power source indication label Refer to the indication label on the bottom side of this unit for the equipment classification, power source, and other information.
About static electricity
Before installing or removing this product, be sure to touch metal objects to
discharge static electricity from your body.
Specifications
- Refer to our technical information website for further information about Power sources and Power consumption information.
- Only when installation work is properly performed according to the Installation Guide and appropriate waterproof treatment is performed.
- Component that has a structure on which the screws that are accessible after installation cannot be screwed or unscrewed using an ordinary screwdriver.
Optional accessories
The latest information → Technical information website “Accessory Selector”
Troubleshooting
Before requesting service, refer to “Troubleshooting” in the Web Guide. Then, confirm the trouble.
Standard accessories
Important Safety Instructions ……………………….. 1 pc
Mounting screw
- Select screws according to the material of the location that the camera will be mounted to. In this case, wood screws and nails should not be used.
- This value indicates the minimum pull-out strength required value per screw. For information about the minimum pull-out strength, refer to our technical information website.
- The screw length is an example when installing the camera on a robust installation surface with a thickness of 20 mm {25/32 inches} or more.
- Ethernet cable with RJ45 plug (category 5e or better, straight, all 4 pairs (8 pins), less than 100m {328 feet})
Installation Procedure
Parts and functions
Step 1 Preparations
Remove the enclosure.
When using a microSD
Step 2
The front side of the template is where the “Hole for the mounting screw
(spare)” is located to the left of the “Cable access hole”.
Step 3
Step 4
When mounting on a ceiling
When mounting on the wall
Using a two-gang junction box
Step 5 → Turn the power on (PoE). Technical information website “IP Setting Software” or “i-PRO Configuration Tool(ICT)”
Step 6
- Be careful not to touch the lens part of the camera during the adjustment.
- Be careful not to let the light-shielding sheet slide beneath the light-shielding rubber of the lens, when adjusting the vertical (TILT) angle.
Step 7
Attach
the enclosure.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>