iBoard IB-022C&H Running Boards Nerf Bars Side Steps Step Bars Installation Guide

: June 1, 2024
: iBoard

Table of Contents

iBoard®
- iBoard® by APS
  - PART#: IB-022C&H
    - PART LIST
  - STEP 1
  - STEP 2
  - STEP 3
  - STEP 4
Read User Manual Online (PDF format)
Download This Manual (PDF format)

iBoard®

Scan for Installation Video

iBoard® by APS

READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
*BODY PANEL MOUNT*
NO DRILLING REQUIRED**

PART#: IB-022C&H

Fastener Size	Tightening Torque (ft-lbs)	Required
6mm	6-7	X
8mm	16-18	√
10mm	31-32	X
12mm	56-58	X
14mm	92-94	X

PART LIST

Front

iBoard IB-022C&H Running Boards Nerf Bars Side Steps Step Bars -
1a

A: Driver Side Step Bar
B: Passenger Side Step Bar

Driver Front Mounting Bracket (DFM)
Passenger Front Mounting Bracket (PFM)
Driver Center Mounting Bracket (DCM)
Passenger Center Mounting Bracket (PCM)
Driver Rear Mounting Bracket (DRM)
Passenger Rear Mounting Bracket (PRM)

Hardware Package (For Stainless Steel Step Bar Installation)

Item	QTY	Description
1#	12	M8X1.25-35mm Carriage Bolts
2#	12	M8 Large Flat Washers
3#	12	M8 Nylon Lock Nuts
4#	6	Sliders (Packed with Step Bars)

1 # 2 # 3 # 4 #

STEP 1

Start the installation under the Passenger side of the vehicle. Remove the front body mount hex bolt, (Fig 1 & 2). Do not remove rubber bushings.

(Fig 1) Bracket Installed

Factory bolt

(Fig 2) Brackets Installation

Factory Body Mount Locations
Factory Bolts
Front

STEP 2

Hang the Passenger Front Mounting Bracket (PFM) to the body mount using the long factory hex bolt, (Fig 1 & 2). Do not fully tighten hex bolt at this time.

STEP 3

Repeat Steps 1 & 2 for Passenger Center Mounting Bracket (PCM) and Passenger Rear Mounting Bracket (PRM) installation, (Fig 1 & 2).

STEP 4

Once all (3) Passenger side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 3 & 4)
(1) Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
(2) Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
(3) Slide the Slider (with carriage bolts) to the Step Bar.
(4) Repeat to install the other (2) sliders to the step bar.
(5) Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and (6) M8 Nylon Lock Nuts and (3) Sliders, (Fig 4). Do not fully tighten hardware at this time.

Note: The Sliders are packed with the Step Bars.
Level and adjust the Step Bar and fully tighten all hardware.
Repeat Steps 1-4 for the other side Step Bar installation. The installation is completed!!!

Attention
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.

iBoard IB-022C&H Running Boards Nerf Bars Side Steps Step Bars -
4
(Fig 3) Slider Installation