JLL T550 Folding Treadmill Instruction Manual

JLL T550 Folding Treadmill

Product Information

Specifications:

• Electrical requirements: Earthed, dedicated circuit
• Voltage: 240V, 50Hz (United Kingdom); 230V, 50Hz (Spain, Italy, Germany, France)

Product Usage Instructions

1. Safety Instructions
   Before operating the treadmill, ensure you read and understand all safety instructions provided in the manual. Some key safety points include:

   • The treadmill must be earthed and connected to a properly installed electrical outlet.
   • Verify that the voltage requirements match the treadmill’s specifications.
   • Do not use a ground plug adapter with a non-grounded outlet.

2. Assembly
   Follow these steps for assembling your treadmill:

3. Prepare the site where you will set up the treadmill.

4. Refer to the provided diagram for guidance on assembly.

5. Check the content listing to ensure all parts are included.

6. Operation
   Operating the treadmill involves the following steps:

   • Familiarize yourself with the control symbols used on the treadmill.
   • Set up the treadmill according to the provided instructions.
   • To start the treadmill, follow the specific starting procedure outlined in the manual.
   • To stop the treadmill, use the designated stop button or method.

7. Maintenance
   To keep your treadmill in good condition, follow these maintenance steps:

   • Regularly lubricate the treadmill using the recommended lubricant and method.
   • Adjust the running belt tension as needed to ensure proper operation.

8. Additional Information
   Refer to the manual for any extra information and disclaimers regarding your treadmill.

FAQ:

• Q: What should I do if my treadmill does not start?
  A: Check that the treadmill is properly connected to an earthed outlet with the correct voltage. Refer to the troubleshooting section in the manual for further guidance.

• Q: How often should I lubricate the treadmill?
  A: It is recommended to lubricate the treadmill every few months or as per the usage frequency specified in the manual.

Please read this book thoroughly before operating the treadmill.

Scan the QR code for a step-by-step video guide on how to assemble your treadmill.

Scan the QR code to view our support center for more technical resolutions and faqs about your item.

Safety Instructions

Please pay attention to the following instructions before operating this treadmill.

ELECTRICAL PREREQUISITES

• This treadmill must be earthed and plugged into an appropriate electrical outlet that is properly installed and earthed by all local codes and ordinances.
• This treadmill is for use on an earthed, dedicated circuit. Make sure that the treadmill is connected to an outlet having the same configuration as the plug. Do not use a ground plug adapter to adapt the power cable to a non-grounded outlet.

IMPORTANT VOLTAGE INFORMATION
Before plugging the power cable into an electrical outlet, verify that the voltage requirements for the site match the voltage of the treadmill that has been received. The power requirements for the unit include an earthed dedicated circuit rated for one of the following. The usual voltage for the United Kingdom is 240V, 50 Hz; Spain is 230V, 50 Hz; Italy is 230V, 50 Hz; Germany is 230V, 50 Hz; and France is 230V, 50 Hz.

WARNING

• Shock and electrocution hazard.
• Connect unthe it to an earthed outlet.
• Do not use a voltage adapter.
• Unplug the unit and let sit for 10 minutes before cleaning or performing maintenance.
• The electrical charge can remain in the unit after unplugging.
• Keep water and liquids away from electrical parts.
• Do not attempt to fix electrical faults if unqualified to do so!

USER SAFETY PRECAUTIONS

BEFORE USE

• When you first assemble your treadmill make sure to check your running belt before use! This is part of the maintenance and instructions on how to perform this can be found on pg. 24.
• Assemble the treadmill according to the instruction manual.
• Consult your doctor before beginning any exercise program.
• Read instructions.
• Read warning labels.
• Read emergency stop procedures.
• Maximum user weight is 150kg/ 23.6 St.
• Inspect unit. If damaged, DO NOT USE.
• Ensure every bolt and screw is securely tightened.
• Place your feet on the side frames when starting or stopping the treadmill.

DURING USE

• DO NOT use for stretching and DO NOT attach straps or other devices.
• DO NOT allow children aged 12 or younger to be on or near the machine.
• Stop exercising if you feel faint, dizzy, or encounter pain.
• Use the handrails for support and to maintain balance.
• Change speed in small increments for safety.
• Keep all clothing and accessories clear of moving parts.
• Wait until the running belt comes to a complete stop before getting off.
• DO NOT jump onto a moving running belt.

EXERCISE SAFETY PRECAUTIONS

• Wear sports clothes and gym shoes.
• Check your shoes regularly and see if there is any dust or hard particles attached which may cause unnecessary damage.
• DO NOT use with bare feet.
• This model should only be used at home, DO NOT be used for commercial purposes.

FACILITY SAFETY PRECAUTIONS

• Connect the treadmill to a properly earthed outlet only.
• DO NOT operate electrically powered treadmills in damp locations.
• Clip the safety key to your clothing.
• Use caution when getting on or off the treadmill.
• Keep the running belt clean and dry at all times.
• After each use, wait until the treadmill comes to a complete stop and is level. Then, switch it off and unplug it. Next, remove the emergency safety key from the treadmill.
• Check the treadmill for worn or loose components before each use. DO NOT use until worn or damaged parts are replaced.
• Maintain regularly. Refer to the Preventive Maintenance chapter.
• DO NOT use the treadmill if: (1) the cable is damaged; (2) the treadmill is not working adequately or (3) the treadmill has been dropped or damaged.
• DO NOT place the cable near heated surfaces or sharp edges.
• DO NOT use the treadmill outdoors.
• DO NOT use the treadmill with 2 or more people running at the same time.
• Read the instruction manual completely before using the treadmill.
• Ensure all users wear appropriate footwear on JLL® equipment.
• Set up and operate the treadmill on a level surface. DO NOT operate in small restricted areas or on plush carpets.
• As far as possible provide the following clearances: 0.5 m at each side and 2 m at the back. Be sure your treadmill is clear of walls, equipment, and other hard surfaces.
• DO NOT modify the treadmill in any way. Any modifications will void the warranty.
• All the data displayed by the monitor is for reference purposes only.

SAFETY KEY
The safety key works as an emergency stop. In the event of falling off the treadmill, the safety key will be pulled out and the power will be switched off at once. Be sure the string is free of knots and has enough slack for you to work comfortably with the safety key in place. Before using the treadmill, clip the safety key to your clothing.

1. Confirm that the safety key is in place at the bottom of the console. The treadmill will not start without the key in its place.
2. Check the safety clip does not fall off in an emergency. Carefully step backward until the key pulls out of the console. If the safety clip falls off your clothing, clip the key again to your clothing and repeat this step until the safety clip is properly attached to your clothes.
3. Ensure the safety clip is secured to your clothing at all times during use.
4. After use, remove the safety key from the treadmill.
5. Store the safety clip on the item holder located on the left or right side of the monitor.

WARNING STICKERS
Warning stickers indicate a potentially hazardous situation that, if not avoided, could result in death or serious injury. Carefully read the following caution and warning labels before using the unit.

• WARNING
  • Do not leave the treadmill before ensuring the machine has been locked tightly and properly. Keep children away from the folded machine.
  • Please do not fold the treadmill if the lock does not work properly. If this problem occurs, please contact our customer service department.

WARNING
Press the lock with your foot to unfold the treadmill. Ensure there are no children nearby.

• It is strictly forbidden to touch any moving parts of the treadmill.
• The plug of this treadmill must be earthed. Do not use this treadmill if the plug is not earthed.
• Please remove the security lock after finishing the assembly.
• Remove the safety key when not in use and store it out of reach of children.
• Using your foot, firmly push against the cylinder to release the folding mechanism.
• Keep small children and pets a safe distance from the treadmill when in use.

Assembly

PREPARING SITE

To find the ideal location to set up this treadmill, ensure that:

• The area is well-illuminated and well-ventilated.
• The surface is level.
• There is enough space to access the unit and emergency dismount. If it is possible, keep the following clearances: 0.5 m at each side and 2 m at the back.
• The treadmill is placed in an environment with a relative humidity range of 30-50%. Please ensure the temperature is kept constant. Do not use it in a moist or damp environment as this may impact the integrity and performance of the machine.

DIAGRAM

CONTENT LISTING

See diagram (left) and content listing (below) for treadmill box contents. See the Customer Service chapter for contact information if any parts are missing.

MAIN BOX

TOOLS PACK

T550 ASSEMBLY

• The treadmill has been assembled and tested at the factory, so you shouldn’t have any problems putting all the parts together. Components are designed to fit together, and only basic tools are required for the assembly process. Inside the box, you will find a Tools Pack (Hex Allen Key, Screwdriver, Washers, and Bolts). See the previous page.

To assemble your JLL T550 please follow these easy steps:

1. Start by attaching the incline lock to the right side of the base using a single small screw.
2. Connect the sensor wire in the right vertical arm at the bottom.
3. Attach both the right and left vertical arms to the base using four Allen head bolts on each side.
4. Connect the sensor wire in the right vertical arm to the wire in the monitor.
5. Slot the monitor onto the vertical arms.
6. Attach the device stand to the monitor using two bolts.
7. Lastly, attach the handrails to either side of the vertical frame arms using two Allen head bolts. These will also secure the monitor to the frame. Then add the bottle holder to the frame.

NOTE:
The fuse you have received with your treadmill is a spare part and is not needed during assembly.

WARNING: HEAVY EQUIPMENT

• It is recommended that at least two people lift, move, and assemble the treadmill.
• Use safe lifting methods.

FOLDING & UNFOLDING THE TREADMILL

• To fold: Hold the end of the running deck by the side frames/rails and lift it until the machine gets to an upright position and you hear a click from the hydraulic cylinder.
• To unfold: Press the hydraulic cylinder with your foot. Push the running deck down, holding it by the side frames. The running deck will go down slowly thanks to the hydraulic system.

SETUP OPTIONS
Use the following instructions to set up the unit settings.

1. Insert the safety key into the corresponding socket.
2. Without anyone on the treadmill, plug in the power cable.
3. Switch on the treadmill. The power switch is under the front end of the machine. The LED display will light up and all the figures in the window will go to ZERO (0).
4. Press the START button and the treadmill will start at 0.3 km/h.
5. Press the + and – buttons to increase or decrease the speed.
6. Press the + and – button to increase or decrease the incline.
7. Press the STOP button twice to stop the machine and clear the data.

To connect your audio via Bluetooth, search for JLLFITNESS on your audio device and select it. Your audio device should now be connected. To control your audio you must do this through your device.

MONITOR CONFIGURATION

Time Display Range

|

00:00 – 99:59

|

Speed Range

| 0.3 – 20 km/h (0.18 – 12.4

mph)

---|---|---|---

Distance Range

| 00.00 – 99.99 km|

Incline Range

| 20 levels

Heart-Rate Display Range

| 50.00 – 99.99 ppm|

Programs

| 30
Calorie Display Range| 0 – 999 Kcal| Max. User Weight| 150 kg, 23.6 st or 330 lb.

When holding the handrail under the console or whilst you are wearing the chest strap a flashing dot will appear on the Pulse signal section on the display and the Distance reading will change and display your Heart Rate (T/min).

TESTING THE TREADMILL OPERATION

Use the following instructions to test the full speed of the treadmill and to check the belt for proper operation.

JLL® recommends that the treadmill is unplugged or the On/Off power (I/O) is switched off (O) when not in use.

1. Without anyone on the machine, plug the treadmill in. Ensure the power cable is not being pinched under the front of the treadmill.
2. Locate the On/Off (I/O) power switch under the front end of the treadmill. Switch it to the on position (I). The display will light up.
3. Press START and the treadmill will start at 0.3 km/h. Check if the monitor is working normally.
4. Observe the belt to see if it is running properly; it should be centered in the middle of the deck. If you have problems with the running belt operation, see Adjust Running Belt in the Preventive Maintenance chapter.
5. Press SPEED INCREASE and SPEED DECREASE to check whether they are working. Run the treadmill through its full speed range. First press the SPEED INCREASE button until the treadmill reaches its highest speed. Then press the SPEED DECREASE button until the treadmill is back to 0.3 km/h.
6. Press the STOP button and check if the machine stops the workout.

WARNING: FALLING HAZARD

When starting the unit:

• Stand on the side frames.
• Do not stand on a running belt.

SPECIFICATIONS

Display

| White LED Displays: Time, speed, distance, heart rate, and incline.
---|---
Programs| 30 running programs. See the Treadmill Program Guide included.
Entertainment| High Powered Speakers & Bluetooth wireless connection.
Storage| Foldable and built-in wheels.
Quick Buttons| Quick Speed: 4, 8 km/h.

Safety

| Emergency safety key, smooth start/stop function, safety handrail, and shock absorption system.
Speed| 0.3 – 20 km/h (0.18 – 12.4 mph)
Incline| 20 levels
Controller| Digital micro-computer controller
Motor| DC Motor (Direct Current Motor)
Horsepower| Continuous power: 2.5HP (1800W), Peak Power: 4.5HP (3350W)
Power Rating| 220 VAC 60 Hz
Working Temperature| 5° C – 40° C
Running Area| 156 cm (Length) x 51 cm (Width)
Maximum User Weight| 150kg, 23.6 St or 330 lb.
Packaging Dimensions| 199 cm (Length) x 77.3 cm (Width) x 36 cm (Height)
Net Weight| 88kg
Gross Weight| 106kg

Operation

Read all instructions, warnings, and safety procedures located in the Safety chapter before using the treadmill.

CONTROL SYMBOLS USED

SETUP

• PAUSE/STOP
  During the treadmill workout, press the STOP button once to stop the treadmill and keep the data recorded so far. If you press the STOP button again, all the digits on the display area will return to ZERO (0).

• INCLINE SETUP
  Before or during the treadmill workout, press the INCLINE UP or INCLINE DOWN buttons on the console.

• QUICK SPEED
  There are two quick speed keys (4km/h and 8km/h). Press START and then any of them to change the speed automatically.

• TOTAL DISTANCE
  With the treadmill in STANDBY mode and all data in the window displaying ZERO (0):

1. Press SET to show set data.
2. Press SET again and hold the button for 5 – 8 seconds to show the total distance. This cannot be reset to zero.

• EXIT SET-UP MODE
  Press the STOP button to exit the Setup options.

STARTING THE TREADMILL
Maximum user weight is up to 150 kg, 23.6 St, or 330 lb.

1. Switch on the treadmill.
2. Place each of your feet on the side frames located on each side of the running belt.
3. Clip the safety key onto your clothing and carefully test the safety key to ensure it will activate in case of an emergency. See Safety Key in the Safety chapter for proper testing of the safety key. Be sure the string is free of knots and has enough slack for you to run comfortably with the safety key in place.
4. Press the START button.
5. Hold the handrail while you step onto the running belt and begin walking.
6. Press the SPEED INCREASE or SPEED DECREASE buttons to change the treadmill speed at any time. The left display will show the current speed.
7. Press the STOP button at any time to stop the running belt.

If the safety key is removed during a workout, the drive motor power shuts off immediately, causing the belt to stop. When a workout is complete, the belt will slow down until it comes to a stop and a workout review will show on the display until you press the STOP button. The treadmill returns to STANDBY mode.

• STOPPING THE TREADMILL
  Press STOP once to pause the workout session. The treadmill will smoothly stop and the accumulated data will be displayed. Press STOP again to end the workout session.

• EMERGENCY DISMOUNT
  If you experience pain, feel faint, or need to stop your treadmill in an emergency, simply pull the safety key off the console. The running belt will then immediately stop.

• SAFETY KEY FUNCTION
  The safety key functions as the emergency stop. In an emergency, remove the safety key from the treadmill and the running belt will stop.

HEART-RATE SENSORS
Hold the sensor plates on the handrail ensuring that your hands are clean. A heart- rate reading will show on the display. Factors that interfere with pulse signal are:

• Hand lotions, oils, or body powder.
• Excessive dirt.
• Excessive movement.

NOTE:

• Heart rate is calculated by PPM (Pulsations per minute), not BPM (Beats per minute).
• The pulse reading is only for your reference and will not be 100% accurate.

HEART-RATE BAND

• This treadmill comes with a heart rate band to be attached around your torso with the sensor approx over your diaphragm.
• The band uses a CR2032 3v battery, to replace it simply unscrew the cap from the back of the band and replace it with a new battery. Please note: Batteries are not provided.
• The elastic strap is fully adjustable and can be detached. After every workout make sure the sensor on the back of the band is cleaned and free of contaminants such as lotions or sweat.
• Once the band has been attached and the treadmill is powered on the two will automatically sync. This means you can monitor your heart rate without having to hold onto the handrail.

DATA READOUTS
As you exercise, the treadmill keeps track of the following data:

• Time: The total time you have been working out or time remaining. Display time as hours: minutes.
• Speed: Your current speed, displayed in kilometers per hour (km/h).
• Distance: The total accumulated distance, in kilometers during your workout.
• Heart rate: Your current heart rate. Heart rate will appear when a pulse signal is detected. Use the sensor plates on the handrail to display your heart rate.
• Incline: Your current incline level, displayed in percentage (%).
• Calories: The total accumulated calories burned during your workout.

ENTERTAINMENT

BLUETOOTH AUDIO INSTRUCTIONS
Turn on the Bluetooth on your device and click or tap on SEARCH DEVICE.

1. Select JLLFITNESS and your device should now be connected to the treadmill.
2. Wait for the treadmill console to beep to confirm the pairing.
3. Open your favorite music player and use the audio controls from your device.

PROGRAMS

• Each program is made up of 10 sections of 200m. At each 200m interval, the speed/ incline may change. If the Stop button is pressed throughout any program this will stop the program and will not be resumed from its current stage. Once the tenth section has been completed the program will loop to start from section one again unless STOP is pressed.
• For more details about the treadmill programs, see the Treadmill Program Guide.

Maintenance

• Maintenance must be performed regularly. Performing maintenance actions can aid in providing safe and trouble-free operation of all JLL® equipment.
• JLL® is not responsible for performing regular inspection and maintenance actions for your machine. JLL® representatives are available to answer any questions that you may have at +44 (0)800 6123 988.

PREVENTIVE MAINTENANCE ACTIVITIES

Every JLL® treadmill that comes from the factory is already lubricated, however, you just need to follow simple steps to maintain it. Keeping the treadmill in a clean state will help to prolong its life. Perform regular preventive maintenance to ensure normal operation of the unit. Keep a log of all maintenance actions to assist in staying current with all preventive maintenance activities. JLL® is not responsible for performing regular inspections or maintenance.

PLEASE NOTE:
Factors such as where the item is stored and how often the machine is used will affect the length of time between the necessary maintenance. It is recommended to perform this maintenance every six weeks after the first 10 months. Details of how to perform the maintenance can also be found on our support center.

Read all instructions and warnings listed both in this chapter and in the Safety chapter. During maintenance, disconnect the power cable. Contact JLL® Customer Service at +44 (0)800 6123 988 for any maintenance or service concerns.

Requirements:

• Water
• Dry cloth
• Allen key
• Vacuum
• Lubrication oil

WARNING

1. Only use water to clean and dust. Do not use any cleaning products because they may damage the treadmill.
2. Be careful not to spill or get excessive moisture between the edge of the display panel and the console, as this might create an electrical hazard or cause failure of the electronics.
3. Direct spraying could cause damage to the electronics and may void the warranty.

Depending on where the treadmill is placed, you may experience dry air, causing a common experience of static electricity. You can notice that by walking across a carpet and then touching a metal object. On your treadmill, you may experience a shock due to the build-up of static electricity on your body and the discharge path of the treadmill. If you experience this type of situation, you may want to increase the humidity to a comfortable level through the use of a humidifier.

Check your machine regularly for rust. If rust starts to appear on the screws it means the item is not housed in the correct environment and will need to be moved to a more suitable room. Any rust will indicate there may be moisture in the air and as a result, this could impact the integrity and performance of your machine.

WARNING

1. Use only JLL® replacement parts.
2. Unplug the unit and let sit for 10 minutes before cleaning or performing maintenance.
3. Keep water and liquids away from electrical parts. The electrical age can remain in the unit after unplugging.
4. If you allow your machine to become rusty, this will affect your warranty.

TREADMILL CLEANING

• Keep the running belt free of dust and debris for smooth running and preventing injuries. Dust/debris may cause damage to the electric motor and other moving parts.
• After every workout use a neat, dry cloth for cleaning the treadmill and the handrail to prevent the machine from corrosion. Wipe away any sweat that may have dripped onto the running belt. Avoid scratching the display by using a soft cloth.
• Contaminants, such as hand lotions, oils, or body powder, may come off on the sensor plates. These can reduce sensitivity and interfere with the pulse signal. It is recommended that the user has clean hands when making contact with the sensor plates. Clean the handles using a cloth dampened with water.
• To clean the console unplug the machine and clean it with a dust-free cloth. For further cleaning, use a soft cloth or paper towel dampened with water. Do not use abrasive or chemical cleaning agents.
• When not using the product for an extended period the product should be disconnected from the power supply.

TREADMILL BALANCE
Place the treadmill on a level floor to avoid it being off-balance. If that is not possible, level the treadmill by adjusting the rubber feet located underneath the frames.

Check if the treadmill is balanced:

1. Stand on the machine with your feet on the side frames.
2. Put your weight on the right side first and then switch to the left side.
3. If you feel any vibrations whilst using the treadmill, adjust the rubber feet located at the base of the frame.

TREADMILL LUBRICATION
If the level of friction between the deck and the belt is high, it will damage the motor and electronics. The running board must be lubricated by a special lubrication oil after a period of usage. A well-lubricated treadmill will be smooth when running and will last longer.

Recommendation (these are just a guideline):

• Less than 3 hours per week of use: Lubricate it every 6 months.
• 3-6 hours per week: Lubricate it every 3 months.
• More than 6 hours per week: Lubricate it every month.

5 STEPS TO LUBRICATE YOUR TREADMILL

Recommendation:

1. Unplug the treadmill.
2. To get access to the deck lift the belt on the treadmill up with your fingers or with something flat and not sharp.
3. Look at the running board or touch it to check if it is oily or not. In case of dryness, use the lubrication oil provided and apply it on the running deck by spreading a straight line down the side of the deck. Ensure that the middle of the board is lubricated.
4. Repeat on the other side.
5. Turn on the machine and leave it running for around 2-3 minutes at 3-4 km/h. Walk on the treadmill to help spread the lubrication oil.

WARNING: EQUIPMENT HAZARD

To avoid serious injury or death:

• Replace worn or damaged components immediately and do not use them until the repair is completed.
• Unplug the unit when not in use or when performing regular maintenance.

ADJUSTING THE RUNNING BELT

• After some time, the user will feel there is a pause sensation whilst running. The running belt can become loose and stretch a bit over time causing a slipping sensation if it is not adjusted and tightened when needed.
• If the belt is too tight, this may cause damage to your motor and/or roller. A belt too loose or too tight can cause wear and tear to both the belt and the board.

HOW TO CHECK IF THE RUNNING BELT IS LOOSE
You can check this every time you use the treadmill by setting the speed to 2-3 km/h then walking on the machine and trying to stop the running belt with your feet while holding the handrail and pulling your body in the opposite direction. If the belt stops, it means that it is loose and needs to be tightened. Another way is checking if the gap between the running belt and the running board is smaller than 5-6 mm, which means that the running belt is loose.

TIGHTENING THE RUNNING BELT

1. Power off the treadmill.
2. Turn the two belt adjustment screws, located at the rear, clockwise to tighten the belt slightly by quarters.
3. Get back on the treadmill and check the belt (read description above). If it is still loose, re-adjust the belt screws by another quarter until you get the required tension on the belt.
4. Run the machine on its own for 1-2 minutes to see if the belt stays in the middle.
5. Do the final test. Leave the machine running for a couple of minutes at 6-8 km/h.
6. If the running belt stays in the center, you can use the treadmill straight away.

ADJUSTING THE BELT WHEN IT’S NOT CENTRED (BEAR LEFT OR RIGHT)
Usually between the frames and the running belt, there should be a gap of 5-6 mm on both sides. If that gap is different it means that the belt is eccentric. So you have to put it back to the right position by following these steps:

1. Power on and set the speed at 2-3 km/h and adjust the screw at the end of the treadmill slowly with the Allen key.
2. If the belt slants to the left, adjust the left bolt clockwise or adjust the right bolt counterclockwise. If the belt slants to the right, adjust oppositely.
3. While adjusting the belt, check if the gap of difference has disappeared, if it is still there, screw the bolt again. Repeat this procedure until the running belt is in the center. It does not need to be aligned perfectly, but ensure it is not scraping or rubbing on anything on the sides.
4. Set the speed at 6 km/h to check if the running belt is still in the same position. Once you check that, the treadmill is ready to use.

ADJUSTING THE MOTOR BELT
After some time, the user will feel there is a pause sensation whilst running. That may be due to a loose motor belt, so adjusting it would be necessary. First of all, you have to check if it is loose following the steps below.

HOW TO CHECK IF THE MOTOR BELT IS LOOSE

1. Unplug the treadmill.
2. Remove the motor cover by unscrewing the bolts on each side. You will see the motor located on the left-hand side of the treadmill.
3. An easy way of checking is by touching the motor belt to feel if it is slack. If you can wiggle the belt up and down, it means that the drive belt is loose.
4. You can check this every time you use the treadmill by setting the speed to 2-3 km/h then walking on the machine and trying to stop the running belt with your feet while holding the handrail and pulling your body in the opposite direction. If the motor stops, it means that it is loose and needs to be tightened.

TIGHTENING THE MOTOR BELT

1. Power off.
2. Locate the four bolts holding the motor.
3. Loosen those four bolts, but do not remove them.
4. Locate the long tensioning bolt that goes from the front edge of the treadmill to the front edge of the motor pallet.
5. Turn the Allen key clockwise to tighten the tensioning bolt just enough to stop it from slipping.
6. Check the tension on the motor belt.
7. Power on the machine and check if the motor belt is still loose (See previous section).

NOTE:
Do not tighten the motor belt too much as this could cause the motor shaft to snap.

Additional Information

CONTACT INFORMATION

• In case any issues arise, please do not hesitate to contact our Customer Service team at +44 (0)800 6123 988 or email us at CONTACT@JLLFITNESS.CO.UK
• You can also visit our support center at SUPPORT.JLLFITNESS.CO.UK for maintenance and assembly articles & videos.

DISCLAIMER

• You should consult your physician, doctor, or other healthcare professional before starting or taking part in any of our workout guides. It is your responsibility to evaluate your health before taking part in or performing any physical activity you may see associated with JLL Fitness Ltd.
• Always seek professional advice before changing your diet or starting any exercise program.
• JLL Fitness Ltd is not liable for any injuries or damages that may occur when assembling or using this treadmill.
• Users must be cautious when using the top speeds on this treadmill. Although the machine has a top speed of 18 km/h, for safety reasons, JLL Fitness Ltd does not recommend exceeding 16 km/h.
• By reading this you assume full responsibility for any injuries or changes to your physical well-being. You waive all rights and release JLL Fitness Ltd of blame for any injuries or damages to property that may occur whilst following our advice.
• This manual offers specific instructions on how to assemble and maintain your treadmill. Failure to follow these directions may result in your warranty being void.

WWW.JLLFITNESS.CO.UK.

Follow us on Facebook and Twitter @JLLFitness. © JLL Fitness Ltd. All Rights Reserved.

References

• Support Centre | JLL Fitness
• JLL Fitness®: Buy Gym & Fitness Equipent Online (Official)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>