ALPS ALPINE China Co Ltd KTX-TH01-EV Tesla Automatic Pop Up Door Handle Instruction Manual

ALPS ALPINE China Co Ltd KTX-TH01-EV Tesla Automatic Pop Up Door Handle

Product Information

Specifications

• Product Name: Tesla Automatic Pop-Up Door Handle
• Model Number: KTX-TH01-EV

Product Usage Instructions

Installation Steps for Tesla Model 3

1. Remove and install left and right front door accessories:

2. Remove the three screws shown in the picture.

3. Pry the lower right corner with a pry knife to remove the door trim panel.

4. Take out the rubber strip and rubber plug at the marking point and align the glass screw with the hole.

5. Remove the plug wire connected to the cover plate and remove the cover plate.

6. Take out the figure lamp from the trim plate and insert it back (very important).

7. Take out the rubber strip and rubber plug at the mark and unscrew the glass screws inside the two circles to take out the glass directly.

8. Remove all screws from the fastening trim plate.

9. Remove all the wires connected with the fixed plate and pull out the lower plate by hand while lifting the lower end of the fixed plate forcefully.

10. Take out the three screws shown in the picture above and remove the original handlebar.

11. Disassemble the signal on the original vehicle to the corresponding electric handle and fix it with the original vehicle screw.

12. Install the second-generation handle on the car and secure it with the original car screws.

13. Remove and install the left and right rear door accessories of Tesla:

14. Circuit Connection Description:

Frequently Asked Questions (FAQ)

• Q: Can I install this door handle on other car models?
  A: The Tesla Automatic Pop-Up Door Handle is specifically designed for Tesla Model 3. It is recommended to consult a professional before attempting installation on other car models.

• Q: Is professional help required for installation?
  A: While DIY installation is possible, it involves complex wiring and disassembly procedures. Professional help is recommended to ensure proper installation.

TESLA AUTOMATIC POP UP DOOR HANDLE

KTX-TH01-EV

Installation wiring diagram

esla Model 3 installation steps

1. model3 Remove and install left and right front door accessories

2. Remove the three screws in the picture above

3. Pry the lower right corner with a pry knife to remove the door trim panel

4. Take out the rubber strip and rubber plug at the marking point and align the glass screw with the hole

5. Remove the plug wire connected to the cover plate and remove the cover plate

6. Take out the figure lamp from the trim plate and insert it back (very important)

7. Take out the rubber strip and rubber plug at the mark and unscrew the glass screws inside the two circles to take out the glass directly

8. Remove all screws from the fastening trim plate

9. Remove all the wires connected with the fixed plate and pull out the lower plate by hand while lifting the lower end of the fixed plate forcefully

10. Take out the three screws in the picture above and remove the original handlebar

11. Disassemble the signal on the original vehicle to the corresponding electric handle and fix it with the original vehicle screw

12. Install the second generation handle on the car and secure it with the original car screws

13. model3 Remove and install the left and right rear door accessories of Tesla

14. Remove the three screws in the picture above

15. Pry the lower right corner with a pry knife to remove the door trim panel

16. Take out the rubber strip and rubber plug at the marking point and align the glass screw with the hole

17. Remove the plug wire connected to the cover plate and remove the cover plate

18. Take out the figure lamp from the trim plate and insert it back (very important)

19. Take out the rubber strip and rubber plug at the mark and unscrew the glass screws inside the two circles to take out the glass directly

20. Remove all screws from the fastening trim plate

21. Remove all the wires connected with the fixed plate and pull out the lower plate by hand while lifting the lower end of the fixed plate forcefully

22. Take out the three screws in the picture above and remove the original handlebar

23. Disassemble the signal on the original vehicle to the corresponding electric handle and fix it with the original vehicle screw

24. Install the second generation handlebars to the car Pair plug directly on the original car, with the original car screw fixed handle

25. Remove the upper edge panel of pillar B and thread the handle line from the bellows to the inside of the car with the string, the wire is hidden in the edge panel of the car

26. Circuit connection Description
    

27. Connect the cable to the battery in the front cover, find a hole on the left side and thread the cable to the co-pilot

28. Remove co-pilot’s A-pillar trim panel and plug the CAN cable directly into the blue socket

29. Remove the decorative plates on both sides of the saddle, and route the left front and rear door handle wire to the position of the copilot control box according to the figure above. The control box is hidden inside the decorative plate

30. Ground wire next to main driver’s foot. After connecting the handle, test the handle to restore the door trim panel when it works normally

Tesla Model Y installation steps

1. Remove and install accessories on the left and right front doors
2. Remove the three screws in the picture above
3. Pry the lower right corner with a pry knife to remove the door trim panel
4. Take out the rubber strip and rubber plug at the marking point and align the glass screw with the hole
5. Remove and remove the plug wire connected to the cover plate
6. The glass has a buckle. You need to hold the screwdriver at the same time to remove the glass
7. Remove the plug connected to the trim plate
8. Remove all screws from the mark and remove the trim plate
9. Take out the three screws in the picture above and remove the original handlebar
10. Disassemble the signal on the original vehicle to the corresponding electric handle and fix it with the original vehicle screw
11. Install the second generation handle on the car and secure it with the original car screws
12. Removal and installation of left and right rear door accessories
13. Remove the two screws in the figure above
14. Pry the lower right corner with a pry knife to remove the door trim panel
15. Take out the rubber strip and rubber plug at the marking point and align the glass screw with the hole
16. Remove the plug wire connected to the cover plate and remove the cover plate
17. Unplug all plugs, remove all marked screws and remove the trim plate
18. Take out the three screws in the picture above and remove the original handlebar
19. Disassemble the signal on the original vehicle to the corresponding electric handle and fix it with the original vehicle screw
20. Install the second generation handlebars to the car Pair plug directly on the original car, with the original car screw fixed handle
21. Remove the upper edge panel of pillar B and thread the handle line from the bellows to the inside of the car with the string, the wire is hidden in the edge panel of the car
22. Circuit connection Description
23. Connect the cable to the battery in the front cover, find a hole on the left side and thread the cable to the co-pilot
24. Remove co-pilot’s A-pillar trim panel and plug the CANcable directly into the blue socket
25. Remove the decorative plates on both sides of the saddle,and route the left front and rear door handle wire to theposition of the copilot control box according to the figureabove. The control box is hidden inside the decorativeplate
26. Ground wire next to main driver’s foot. After connecting the handle, test the handle to restore the door trim panel when it works normally

After connecting the handle, test the handle to restore the door trim panel when it works normally

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>