CF Moto ZForce 950 Door And Rear Window Installation Guide
- June 1, 2024
- CF Moto
Table of Contents
3 STAR INDUSTRIES
CF Moto Z Force 950
Door and Rear Window
Your enclosure is made of heavy duty fabric that is water repellent and resistant to mildew, ultra-violet rays and abrasion.
Surface Preparation Instructions and Guidelines
Cleaning: To achieve a strong bond between Velcro adhesive and UTV
surface, you must clean the surface. Use a mixture of 50% alcohol and 50%
water to remove dirt, mud and dust from roll bars and plastic body components.
Let dry.
Repeat this process 3 times.
The adhesive hook should be applied at a temperature of 70 degrees or above.
Bond between UTV and adhesive hook is dependent upon the amount of adhesive to
surface contact development. Firm application pressure develops a better
adhesive contact and improves bond strength.
After application, the bond strength increases and approaches the ultimate
bond strength after 72 hours. Bond strength build up: 20 min equals 50% bond
strength, 1 hour equals 75% bond strength, one day equals 90% bond strength,
and 3 days equals 100% bond strength.
More tips for installation.
Two is better than one: We recommend a second person be involved for the
installation process. Getting the panel in the correct position takes some
pulling and tugging, we find the process runs smoother when there are two
people pulling.
Test adhesion: Use a small piece of Velcro, remove backing and adhere to
roll bars. Wait 20 minutes, Velcro should already be difficult to remove.
Still having trouble with adhesion: If Velcro is still not adhering to the
roll bars, use a piece of hook (rough side of Velcro) to “rough up” the
surface of your roll bar. We do not recommend this for the plastic body of
your UTV, it will scratch.
Unsure about Velcro placement: With-out removing the white backing, attach the
Velcro to your enclosure panel. Hold panel up to the UTV and note the area
that the Velcro should attach. You can use the double-sided straps with-out
Velcro to help hold up the panel while you remove the white backing and adhere
sticky Velcro. We will send extra Velcro that can be used to hold the
enclosure to the cab frame for easy notation of Velcro placement.
Attaching panel: Attach the panel top first, then work your way around
the panel pulling the tabs and sticking them to the corresponding adhesive
Velcro. The webbing (black trim) of the panel should align to the middle of
the roll bar.
Installing with Windshield and Hard Top.
If you have a windshield and or hard top on your UTV, you will need to remove
them before installing the door panels.
After the installation of your enclosure is complete you will then reinstall
the windshield and hard top.
If clamps for the windshield or hard top are interfering with the sewn-on
Velcro tabs or straps on your enclosure you can modify the tabs and straps
easily by cutting them to fit. Mark where the tabs need to be cut to
accommodate your windshield or hard tops clamps or bolts. Cut the tabs and
burn the edges with a lighter to prevent unraveling. Do not cut into the
binding (darker black trim around your door panel).
Installation Instructions
Step 1: Remove your 3SI UTV Cab Enclosure and Velcro kit from the
shipping box.
Step 2: Remove exsisting windshield and hard top.
Step 3: Clean all surfaces on which you will be placing the adhesive
Velcro according to the surface preparation instructions. Wait until the
surfaces are dry.
Step 4: Remove the backing from the adhesive hook strips and install as
indicated in the following adhesive hook table and pictures. Press firmly.
Step 5: Wait 72 hours! This step is very important to the life of your
Velcro. Waiting the full 72 hours will ensure that your Velcro and enclosure
will stay on in rain, sleet, snow or mud.
Step 6: After all adhesive Velcro strips are attached, begin attaching
each panel to the cab frame.
Step 7: After all panels are attached work your way around the UTV
remove, pull, and reattach each Velcro tab to achieve a tight fit. You may
need to do this a few times.
Step 8: When your enclosure is in the correct position the binding or
trim around the panels will rest in the center of the roll bar. If you have a
windshield the binding, will rest along the edge of your windshield.
Step 9: Re-install your windshield and hard top.
See enclosed Product Care sheet for instructions on how to properly care for
your 3SI UTV Enclosure.
REAR PANEL
PICTURES SHOWS THE SEWN ON TABS AND STRAPS THAT CORRESPOND TO THE
VELCRO CHART
ADHESIVE VELCRO CHART
BACK PANEL
Reference| Qty / Size| Placement
A| 2-13”| Attach horizontally to the center of the top rear roll bar, Velcro
facing the inside of the cab. (FIGURE 1)
B| 2-30”| Attach vertically to the rear rollbars. (FIGURE 2)
C| 2-12”| Attach to the outside of the back body. (FIGURE 2)
D| 1-15”| Attach to the center of the outside body. (FIGURE 2)
Figure 1: SHOWS POSTION OF VELCRO
STRIPS (A).
Figure 2: SHOWS POSITION OF VELCRO STRIPS
(B, C, AND D),
PICTURES SHOW THE SEWN-ON VELCRO TABS AND
STRAPS THAT CORRESPOND TO THE VECRO CHART. BOTH DOORS HAVE IDENTICAL TABS AND
STRAPS.
CF MOTO Z FORCE 950
DOOR PANEL
ADHESIVE HOOK TABLE
DOOR KIT
| REFERENCE | QUANITY/SIZE | PLACEMENT |
|---|---|---|
| A | -39” | Attach horizontally to the top side roll bars. (FIGURE 1) |
| B | 2-19” | Attach to the front side roll bars on either side of the UTV |
extending the adhesive Velcro the length of the roll bar. (FIGURE 2)
C| N/A| Attach to the rear roll bars. (FIGURE 3)
D| N/A| Attach to the rear roll bars. (FIGURE 3
E| N/A| Attach to the lower portion of the rear roll bars. (FIGURE 3)
F| 2-15”| Attach horizontally to the outside of the UTV behind the top door
hinge. (FIGURE 4)
G| 2-15”| Attach vertically to the outside of the UTV. (FIGURE 5)
H| 2-21”| Attach to the outside body of the UTV you may need to cut this
strip so that it follows the curve of the UTV. (FIGURE 5)
I| 2-16”| Attach horizontally to the outside of the UTV. Floor area.
(FIGURE 5)
J| 2-6”| Attach to the inside of the UTVs wheel well. (FIGURE6)
K| 2-16”| Attach to the inside of the UTVs wheel well. (FIGURE6)
L| 2-32”| Attach to the inside of the UTVs wheel well. (FIGURE6)
M| 4-6”| Not pictured. Wrap adhesive strips around the arm bar.
Figure 1: SHOWS PLACEMENT OF VELCRO STRIPS (A)
Velcro straps on the doorwill wrap around the roll bar and attach to the same
adhesive strip A. 
Figure 2: SHOWS PLACEMENT OF VELCRO
STRIPS (B) 
Figure 3: YOU WILL FIND THE VELCRO FOR THESE
TABS ARE SEWN ON TO THE BACK PANEL. Figure 4:
SHOWS PLACEMENT VELCRO STRIPS (F)
Figure 5: SHOWS PLACEMENT OF VELCRO STRIPS (G, H AND I) STRIP H MAY NEED TO BE
TRIMMED IN ORDER TO FOLLOW THE CURVE OF THE UTV.
Figure 6: SHOWS PLACEMENT OF VELCRO STRIPS (J, K AND L) THE
ADHESIVE VECLRO WILL BE PLACED ON THE INSIDE OF THE UTV
WHEN INSTALLED CORRECTLY THE DOOR KIT WILL BE SQUARE AND TIGHT ON THE CAB
FRAME. YOUR DOOR KIT SHOULD RESEMBLE THE PHOTO BELOW.
3 STAR INDUSTRIES
Care Instructions
Heavy Duty Marine and Mil-Spec Military Fabric Cleaning
All 3SI UTV Enclosure Heavy Duty Marine and Military Camo fabrics are
guaranteed against excessive loss of color or strength under normal exposure
and use conditions. Periodic cleaning with a solution of 4 ounces of bleach
and 2 ounces of soap (NOT DETERGENTS) in one gallon of water is recommended to
minimize accumulations of dirt, bird droppings and other contaminants which
can support surface mildew and stain fabric.
Soft Vinyl Window Cleaning
3SI UTV Enclosure Vinyl Windows will remain clear and provide great visibility
under normal exposure conditions if properly cleaned. Periodic cleaning with a
solution of 1 ounce of soap in one gallon of water is all that is needed to
maintain good window cleanliness and visibility. Caution: DO NOT USE ANY
DETERGENTS, WINDOW CLEANERS, SOLVENTS or CHEMICALS OF ANY KIND TO CLEAN VINYL
WINDOWS AS THESE WILL CLOUD THE WINDOWS. ALSO, NEVER RUB WINDOWS WITH A DRY
CLOTH OR RAG.
Storage Recommendations
Before removing the 3SI UTV Enclosure from your vehicle for storage, clean the
Fabric and Vinyl Windows thoroughly as indicated above. Any dirt remaining on
the Enclosure may scratch Vinyl Windows while in storage. Once the Enclosure
has been cleaned it should be placed on a large flat surface. Lay the
Enclosure out so that Vinyl Windows are in a flat position. Fold the doors
over the rear panel first then fold the top and windshield on top of the doors
keeping the Vinyl Windows flat. Caution: FOLDING VINYL WINDOWS WILL CAUSE
PERMANENT CREASE DAMAGE AND WILL VOID ALL WARRANTIES. Once the Enclosure is
folded keeping all Vinyl Windows flat, begin rolling the Enclosure into an 8”
roll. Place the 8” roll into a box and store at normal room temperature. To
ensure long life of your enclosure it is best not to store in extreme
temperatures.
Hauling
The ONLY products manufactured by 3SI UTV that can be hauled while installed
are the hard windshields, full cab enclosures, and door/rear window combos
with top and windshield installed. However, the full cab enclosures and
door/rear window combos should be tied down before hauling. Speed should not
exceed 55 mph while hauling to prevent ripping and shredding of the material
and zippers. NEVER HAUL INSTALLED SOFT TOPS, WINDSHIELD TOP COMBOS, AND SUMMER
CABS. REMOVE BEFORE HAULING.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>