Waterdrop WD-FF-01A Activated Carbon Fiber Faucet Replacement Filter Instruction Manual

Waterdrop WD-FF-01A Activated Carbon Fiber Faucet Replacement Filter

Product Specifications

• Manufacturer: Qingdao Ecopure Filter Co., Ltd.
• Technical Support: Tel: 1-888-352-3558 (US), Email: service@waterdropfilter.com
• Origin: China

Product Usage Instructions

Installation and Replacement Procedures

1. Turn the filter cover counterclockwise to remove it.
2. Insert the new filter into the filter base and remove the old filter.
3. Turn the filter cover clockwise to secure it.
4. Align the slot of the filter base with the slot of the mounting base.

Note: Before use, run cold water for 1 minute in the pure position to rinse the filter.

Frequently Asked Questions (FAQ)

Q: How often should I replace the filter?

• A: It is recommended to replace the filter every [specific time frame] or after [specific number of gallons] of water usage for optimal performance.

Q: Can I clean the filter instead of replacing it?

• A: No, the filter is not designed to be cleaned. It should be replaced according to the manufacturer’s recommendations for continued efficiency.

ACTIVATED CARBON FIBER FAUCET REPLACEMENT FILTER

• MODEL: WD-FF-01A
• Replacement for the following water filtration system.

Waterdrop

• Activated Carbon Fiber Faucet Filtration System
• Filter Life: optimal results for up to 3 months or 320 gallons, whichever comes first will vary based on water condition.
• Tested and Certified by NSF International in Model WD-FC-01/WD-FC-03 against NSF/ANSI Standard 42 for the reduction of the claims specified on the Performance Data Sheet, and to NSF/ANSI 372 (≤0.25% lead).

OPERATING SPECIFICATIONS

• Operating Temperature: 41-122 °F (5-50 °C)
• Operating Pressure: 15-100 psi (100-689 kPa)
• Rated Capacity: 320 gallons (1,200 liters)
• Flow Rate: 0.5 gpm (2 Ipm)

NOTE:

• Do not use water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

INSTALLATION AND REPLACEMENT PROCEDURES

1. Twist the Filter Base from the Mounting Base.
2. Twist the Filter Top Cover off and take out the old filter.
3. Insert the new filter into the Filter Base.
4. Twist the Filter Top Cover on.
5. Align the slot of the Filter Base with the slot of the Mounting Base.
6. Insert the Filter Base into the Mounting Base and rotate 90° upward.

NOTE: Before first use, run cold water for 1 minute in a “pure” position to flush the filter.

STORAGE AND MAINTENANCE

• Replace your filter every 3 months or 320 gallons to prevent bacteria and fungus growth in your filter supply lines, and storage tank.
• Keep your unused filters in a cool, dark, and dry place until you need them.

WARNINGS

• Do not use water above 122 °F / 50 °C.
• To reduce the risk of property damage due to water leakage, this filter MUST be installed under the operating specifications and instructions.
• This filter unit must be replaced regularly. alume to roll position or lady ratidamage caring oil issue are further, manufacturer

FREQUENTLY ASKED QUESTIONS

Why does water leak between the mounting base and the faucet?

The filter may not have been installed properly. Or the silicone washer may be damaged Re-install the filter. Wrap Teflon Tape around the joint of the mounting base and the faucet. If it doesn't work, replace the silicone washer.

Why does the filtered water run quite slowly?

The filter cartridge may be clogged. Replace the filter cartridge.

Why does the unfiltered water run quite slowly?

There may be dirt in the filter steel mesh. Clean the filter steel mesh.

Why does the water taste funny?

The filter cartridge is not installed appropriately, or it should be replaced. Please re-install it correctly. If there is still bad taste, please replace it.

PERFORMANCE DATA SHEET

• Manufacturer Technical Support
• Tel: 1-888-352-3558 (U.S.)
• E-mail:service@waterdropfilter.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>