sw-motech STP.01.590.10400-B Frame Pads Kit Installation Guide
- May 15, 2024
- SW-MOTECH
Table of Contents
sw-motech STP.01.590.10400-B Frame Pads Kit
Specifications
- Model Numbers: STP.01.590.10400/B, STP.01.590.80400/B, STP.00.590.10001/B
- Color: Black
- Material: High-quality plastic
Product Usage Instructions
Installation
- Ensure the area where the product will be installed is clean and dry.
- Refer to the ANBAUANLEITUNG for step-by-step installation instructions.
- Use the provided hardware and tools to securely attach the product.
Operation:
- Make sure the product is properly installed before use.
- Follow the user manual for guidelines on product operation.
- Do not exceed the recommended weight limit for the product.
Maintenance
- Regularly inspect the product for any signs of wear or damage.
- Clean the product with a damp cloth and mild detergent as needed.
- Do not use harsh chemicals or abrasive cleaners on the product.
Mounting Instruction
Mounting kit for frame slider HONDA CBF 600 S
- Mounting Instruction
- SW-MOTECH products should be installed by a qualified, experienced motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. SW Motech takes no responsibility for damages caused by improper installation.
- All screws, bolts, and nuts, including all replacement hardware provided by SW-MOTECH, should be tightened to the torque specified in the OEM maintenance manual for young motorcycles. If no torque specifications are provided in the ver maintenance manual. the following torques may be used:
PARTS AND TOOLS
Attention: First attach the frame slider on the left side, then on the right side. Never attach both frame sliders, or remove both engine bolts at the same time.
- Attach parts (2), (4), and (6) as shown in step 1. Do not fully tighten the screw (4).
- Adjust the mounting plate (2) according to the alignment of the motorcycle.
- Now tighten the screw (4). Pay attention to the manufacturer’s specified torque.
- Then attach the parts (1) and (3), as shown in step 2.
NOTE: Also refer to the mounting instructions of the frame slider set (*). Use on the right side screw (5).
INSTALLATION
Revision: 00 / Date: 10 – 2019
Crash pad set
Thank you for choosing this premium product from SW-MOTECH.
- Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our website. Installation and/or maintenance of this product requires good technical understanding! For your own safety, SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
- Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly.
- Nonconformance can lead to vehicle damage or even endanger the driver!
- These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
- This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance.
- Installed accessories can change the driving behavior and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled by the vehicle manufacturer’s specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with a medium-strength liquid thread locker. Torque specifications undefined by SW- MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also, make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.
- Packed by:
- Date of packaging:
PARTS LIST
Step No. Item No. / Description
Part/Anzahl/Quantity/ N.m
- Crash Pad; left / right: 2 /2
- Logo Insert: 2/2
- Lenshead Screw, self-tapping: 2/2: max. 1,2
All measurements in millimeters.
The second number indicates the total quantity of the part in the delivery.
No torque specifications: Use the torque defined by the vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
MOUNTING
- Step [1]: Attach the crash pads (1) on both sides to the adapter plates of your SW-MOTECH slider set for frame, as described in the mounting instructions of the slider set for frame.
- Step [2]: Place the logo inserts (2) on both sides into the crash pads …
- Step [3]: … and attach them with the screws (3).
Tighten the screws (3) CAREFULLY by hand (max. 1,2 N-m)!
SW-MOTECH GmbH & Co. KG
Errors and omissions excepted. Technical and design modifications are subject
to change.
FAQ
Frequently Asked Questions
Q: How do I know which model number I have?
A: The model number can be found on the product packaging or on a label attached to the product itself.
label attached to the product itself. Q: Can this product be used outdoors?
A: It is recommended to use this product indoors to prevent damage from exposure to outdoor elements.