SEALEY LED100C 3w Cob Led Worklight With Clamp Instruction Manual

SEALEY LED100C 3w Cob Led Worklight With Clamp

Specifications

• Model No.: LED100C
• Batteries: 3 x AA (not included)
• LED type: 3 W COB
• Lumen output: 250 lm
• Operating time: 5 hrs

Product Usage Instructions

Safety

General Safety

• DO NOT shine directly into the eyes.
• DO NOT allow children to use the torch.
• DO NOT use if the battery or casing is damaged.
• DO NOT leave batteries in a discharged state; remove before storage.

Battery Safety

• DO NOT open batteries.
• Avoid crush, puncture, short contacts, or dispose of in fire or water.
• Replace with compatible batteries only.
• Recycle or dispose of used batteries following local regulations.

Introduction

This worklight features a 3W COB LED producing up to 250lm. Made from ABS plastic with a molded grip and soft finish. The clamp opens up to 3 inches, and the lamp can be separated for handheld use or mounted on a magnetic surface. It includes a 360-degree rotating ball joint for greater coverage and requires 3 x AA batteries (not included).

Operation

Removing Lamp from Clamp

To remove the lamp from the clamp mount, depress the small tab on the underside of the lamp mounting base and slide the lamp upwards and away from the tab.

Battery

To insert or replace batteries, twist and separate the light housing and light mounting base to expose the battery compartment. Insert new batteries according to the polarity markings and reassemble the unit.

On/Off Switch

To turn the light on, depress the button. Another press will turn it off. When separated from the clamp, the lamp can be mounted on a magnetic surface or used as a handheld torch.

FAQ

• Q: What type of batteries does the LED100C worklight use?
  • A : The LED100C worklight requires 3 x AA batteries (not included).
• Q: Can the lamp be used separately from the clamp?
  • A : Yes, the lamp can be separated and used as a handheld torch or mounted on any magnetic surface.
• Q: What is the operating time of the LED100C worklight?
  • A : The operating time is approximately 5 hours.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT : PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

GENERAL SAFETY

• DO NOT shine directly into your, another person’s or an animal’s eyes.
• DO NOT allow children to use the torch.
• DO NOT use the torch if you suspect that the battery or the torch casing is damaged.
• DO NOT leave batteries in a discharged state. Before storage remove batteries and dispose of in the correct manner.

BATTERY SAFETY

• WARNING! To reduce the risk of burns or fire:
• DO NOT attempt to open the batteries.
• DO NOT crush, puncture, short contacts or dispose of in fire or water.
• DO NOT expose to temperatures above 60°C (140°F).
• Replace only with the batteries designed for this product.
• Recycle or dispose of used batteries as stipulated by local regulations.
• If the electrolyte in the batteries gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with cool water and seek immediate medical attention.

INTRODUCTION

3W COB LED that produces up to 250lm. Made from tough ABS plastic with a molded grip and a soft finish. The clamp opens up to 3 inches. Lamp can be separated from the grip and used as a small hand-held torch or mounted to any magnetic surface. Features 360-degree rotating ball joint to allow for greater coverage. Requires 3 x AA batteries (not Included)

SPECIFICATION

• Model No.:……………………………………………. LED100C
• Batteries:……………………………….. 3 x AA (not included)
• LED type.: ………………………………………………3 W COB
• Lumen output : …………………………………………… 250 lm
• Operating time : ……………………………………………. 5 hrs

OPERATION

REMOVING LAMP FROM CLAMP

The lamp can be removed from the clamp mount by depressing the small tab on the underside of the lamp mounting base and sliding the lamp upwards and away from the tab.

BATTERY

To insert or replace batteries, twist and separate the light housing and light mounting base in opposite directions to expose the battery compartment.

Insert the new batteries according to the polarity markings in the base and reassemble the unit.

ON / OFF SWITCH

To turn the light on depress the button (fig.1). One further press of the button will turn the light off.

NOTE : When the lamp is separated from the clamp it can be mounted to any magnetic surface or used as a small hand-held torch.

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

WEEE REGULATIONS

Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

BATTERY REMOVAL

Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.

Note : It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important : No Liability is accepted for incorrect use of this product.
Warranty : The guarantee is 12 months from the purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

• 01284 757500
• 01284 703534
• sales@sealey.co.uk
•   www.sealey.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>