DAYTONA 80920 Cube Digital Speed and RPM Meter Instruction Manual
- June 1, 2024
- DAYTONA
Table of Contents
DAYTONA 80920 Cube Digital Speed and RPM Meter
Specifications:
- Product Name: Cube Digital Speed & RPM Meter
- Model Number: #80920
- E-Marked
- Power Supply: DC 8-18V (regular 12V)
Product Information
The DAYTONA ‘Cube’ display instrument is a high-quality digital speed and RPM meter designed for motorcycles. It features various functions such as digital speedometer, odometer, voltmeter, dual trip meter, and RPM meter. The product is E-marked and designed to provide accurate and reliable readings for your motorcycle.
Installation:
- Disconnect the ground wire from the vehicle’s battery before installation.
- Connect the Red wire to a wire that provides current when the main switch is turned on.
- Ensure proper wiring to prevent malfunction of the gauge.
- Refer to the assembly and installation manual for detailed instructions.
Usage Instructions
Proper installation and electric connection require technical expertise, special tools, and skilled craftsmanship. If unsure, seek assistance from a trained mechanic for safety.
Components:
- Gauge Unit
- Bracket
- Extension Wire Set
- Cap Screw
- Spring Washer
- Washer
- Resistor 1M ohm
- HEX wrench
- Setting switch
Wiring Recommendations:
Connect the yellow wire to the positive terminal/wire of the ignition coil. For Harley-Davidson motorcycles, connect the yellow wire to the red wire of the crank position sensor. Ensure correct RPM pulse detection for accurate readings.
Calibration:
To calibrate and test your ‘Cube’ display for correct speed and RPM values, follow the instructions provided in the manual.
FAQ
The speedometer does not work correctly.
Speed calibration must be completed before testing. Check if calibrated correctly and ensure correct wiring of the speed sensor wire.
How can I check if the speedometer is working or not?
Access the speed calibration settings, choose Auto-Calibration mode, and touch the speed sensor wire to the negative terminal of the battery. Verify if the display shows increasing numbers.
The speedometer stops working while riding the motorcycle.
Keep the meter cable away from high voltage components such as plug chords and ignition coils to avoid interference.
The Speedometer moves while engine is idling.
Check if the battery is drained and ensure proper connections to prevent erratic readings.
RPM is not displayed correctly.
Try changing the RPM pulse detection to one of the other methods. Connecting
to the primary terminal of the ignition coil is recommended.
･Add a 1 MΩ resistor to the RPM signal line.
OPTION
For the detailed information on optional parts, please kindly visit our website by scanning the QR code →
- Thank you for choosing a high-quality DAYTONA ‘Cube’ display instrument. With proper installation and connection, you will have long-lasting pleasure with this high-quality product when used as intended.
- When installing, please make sure that the speed indicator is located in the immediate view of the driver.
- Attach the housing securely to the enclosed bracket or mount with an at least equivalent holder permanently to the bike. Do not use longer screws to connect the holder to the housing, as longer screws can damage the instrument’s internal components. Attach the instrument in a way that no part obstructs or restricts the steering. Route the wiring in such a way, that the full steering angle works in both directions without hindrance and no cables are pinched or under tension when the steering moves. Protect the cabling, also in the long term, against chafing and damage during the constantly occurring steering movements. Read this assembly and installation manual before installing and operating the display instrument.
- Proper installation and electric connection requires technical expertise, special tools and skilled craftsmanship.
- If you are unsure about the installation, have it done, for your own safety, by a trained mechanic.
CAUTION
- Read all instructions before use.
- Needs to purchase the optional speed sensor if the vehicle does NOT come with an electrical speed sensor. Or use a converter (sold separately) that turns mechanical movement into electrical pulse, if the vehicle comes with a mechanical speedometer cable. (See the optional parts section in this manual.)
- Designed for a 12V system vehicle. ‘Cube’ gauges do NOT work with a 6V system or a battery-less system. ‘Cube’ gauges might not work normally when used together with other device that emits much noise.
- Use ‘Cube’ gauges for the intended purpose of use.
- ‘Cube’ gauges is for universal use, so it needs wiring for installation. Do the wiring referring to the vehicle owner’s manual. (If you are not sure about installation, consult an experienced dealer.)
- Do NOT disassemble ‘Cube’ gauges. It may be damaged and water may come in.
- Do NOT leave ‘Cube’ gauges in hight heat when not used for a long time.
- Do NOT hit, drop or give a shock on ‘Cube’ gauges. It may be damaged.
- Avoid contact with gasoline, brake fluid or other chemicals. It may be damaged.
- After installation, check to see if all the parts are correctly installed, and to see if all the screws are properly tightened.
- Inspect all installed parts after 100km driving. Periodical inspection is required every 500km(300mile).
- If anything unusual found while driving, pull over at a safe place to check.
PRODUCT FEATURES
- Digital speedometer and rpm-meter
- Odometer (NOT Resettable) : 0-99,999km (mile)
- Dual Trip Meter (Resettable) : 0.0-9,999.9km (mile)
- RPM Meter : 10,000 or 20,000rpm selectable
- Ability to connect to OEM speed sensor, if the vehicle is equipped with an electrical speed sensor.
- 50mm×50mm×25mm(1.97”×1.97”×0.98”)
- Voltmeter : DC8.0-18.0V
- KM/H or MPH selectable
- Power DC8-18V (regular 12V)
COMPONENTS
INSTALLATION
- Wrong wiring may cause malfunction of the gauge.
- Make sure to have correct wiring.
- Disconnect the ground wire from the negative post of vehicle’s battery before installation.
- The Red wire is to be connected to the wire that gives current when the main switch is turned on.
RPM pulse detection
Connect RPM pulse correctly. Wrong wiring causes malfunction of the gauge.
If the RPM is unstable, insert the included “⑦ Resistance 1M ohm” into the RPM
Pulse line.
ATTENTION!
Wiring alone will not make ‘Cube’ display correct speed or RPM values. To
calibrate and test your ‘Cube’ , please see the next page for instructions.
BUTTON OPERATION AND SETUP
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>