Healtech Electronics MM-T02 Service Light Reset Tool For Triumph Motorcycles User Manual
- June 1, 2024
- HEALTECH ELECTRONICS
Table of Contents
Healtech Electronics MM-T02 Service Light Reset Tool For Triumph
Motorcycles
Specifications
- Supply voltage: +8V to +24V Waterproof (IP68)
- Max. supply current at 12V: 60 mA
- Size: 59 x 35 x 17 mm (2.3 x 1.4 x 0.7 inches)
Product Usage Instructions
Compatibility Check
Before using the Maintenance Mate service light reset tool, ensure your
Triumph motorcycle is compatible with this tool. Check the part number on the
packaging and use the Product Advisor on the HealTech Electronics website to
verify compatibility.
Dashboard Display
When the ignition key is on and the distance to service is 800 km (500
miles) or less, the service symbol will be displayed for 3 seconds with the
remaining distance. At 0 km (0 miles), the service symbol will stay on until
the service is done. An overdue warning may appear if service is overdue.
Features
The Maintenance Mate offers touch control for setting intervals, a rugged
design encased in epoxy resin, and is water-resistant (IP68). It is cost-
effective, light, and small in size for easy handling.
Warranty
HealTech Electronics Ltd. provides a two-year warranty against defects
starting from the purchase date as indicated on the invoice.
Cleaning and Storage
Clean the unit with a wet sponge using water only. Avoid detergents or dry
cloth which may scratch the unit’s front face.
Operation
- If the speedometer indicates MPH, switch to Km/h.
- Locate diagnostic connector: MM-T02 (BLACK, 16-pole) or MM-T03(RED, 6-pole) under the rider’s seat.
- Connect the MM unit ensuring the engine stop switch is in position.
Foreword
- Before using this product please ensure the bike is compatible with this tool. See the part number on the packaging and use the Product Advisor on our website to check compatibility. For more information on this product, please visit: www.healtech-electronics.com/MM
- Congratulations on your purchase of a Maintenance Mate service light reset tool.
- Products from HealTech Electronics Ltd. are the most advanced aftermarket accessories and maintenance tools for motorcycles.
- The Maintenance Mate is compatible with a wide range of Triumph motorcycles (2010onwards, depending on model) that have a service interval indicator light (small wrench symbol) on the dashboard
- When the ignition key is switched on and the distance to service is 800 km (500 miles) or less, the service symbol will be displayed for 3 seconds and the dash will show the distance remaining.
- When the remaining distance is 0 km (0 miles), the service symbol will stay permanently on until the service has been carried out and the service interval & date has been set. If the service is overdue, the distance will be displayed as a negative number or you will see an OVERDUE warning with the wrench symbol (depending on the bike model).
- The Maintenance Mate will set the service interval & date on the bike without the need for a complex and expensive OBD tool. Faster, easier, and more efficient for busy workshops.
Features
Touch control
Set the next interval with ease using the touch pads. The touch-sensitive area
is marked with arrow signs pointing up and down on the face of the unit.
Built to last
- Rugged design, encased in epoxy resin.
- Only high-quality SMD components are used.
- Each unit is extensively tested before shipping.
- Oil and water resistant (IP68).
Cost effective option
- Save on service bills! The MM is an economical solution for bike owners who can do their own maintenance.
- Save on servicing time! No need for laptops or dedicated OBD tools. Faster turnaround and lower costs for workshops.
Light and small
The unit itself is hardly larger than the OEM diagnostic connector it connects
to.
Warranty
- HealTech Electronics Ltd. guarantees this product against defects in material and workmanship for a period of two (2) years.
- The warranty period starts from the date of the original purchase as shown on the invoice.
Specifications
- Supply voltage: +8V to +24V
- Max. supply current at 12V: 60 mA
- Operating temp: -40°C to +80°C (-40°F to +176°F)
- Waterproof (IP68)
- Size: 59 x 35 x 17 mm (2.3 x 1.4 x 0.7 inches)
- Reverse polarity and transient protection
Cleaning and storing the unit
Clean the unit with a wet sponge. Use water only, without any detergents. Do not clean with a dry cloth as it may scratch the front face.
Operation
- If the speedometer is set to MPH reading, change the indication in the dash menu from MPH to Km/h.
- Locate the diagnostic connector (usually it’s under the rider’s seat and has a removable cap): MM-T02: BLACK, 16-pole; MM-T03: RED, 6-pole.
- Connect the MM unit.
- Make sure the engine stop switch is in the RUN position, the ignition key is switched ON and the gearbox is in Neutral. Do NOT start the engine.
- Now a number (0-20) should appear on the display of the unit, depending on the last successful upload. Otherwise, check that the connectors are fully mated and there are no bent terminals.
- The service interval can be set between 0-20,000 km.
- Now set the desired service date as well, otherwise the OVERDUE message won’t disappear from the Service menu.
- After setting the service date, check in the service menu, whether both the service Interval and date are successfully set or not. If yes, you’re all set.
Displayed values and their meanings
Changing the value
- With the UP and DOWN arrow symbols select the desired value between 0 and 20,000 km.
- Tap and release one of the touch pads. The number changes when you release the pad.
- Holding the pad continuously will not alter the value.
Setting the service interval
- Touch and hold both the UP and DOWN arrow keys. After about 3 seconds the ‘UP’ sign will flash a few times on the display, indicating the upload was successful. Release the touch pads.
- If the upload fails, an ‘Er’ (Error) sign will appear. Check that this motorcycle has a service interval indicator. If so, repeat the steps described in Chapter 5 and try setting a lower service interval.
Note:
- If you perform the upload more than once, only the last uploaded interval will be set.
- If you attempt to set a value higher than valid for a particular motorcycle, the highest valid value will be set. Please refer to the bike’s Service Manual.
Setting the service date
As soon as you upload the service interval value, a ‘d1’ sign will appear and
a number right after. ‘d1’ stands for the year in the service date. Select the
desired value and hold both the UP and DOWN arrow keys for about 3 seconds. A
‘d2’ sign will appear, which stands for the month of the service date. Set it
the same way as the year. Now a ‘d3’ will appear, which is the day of the
service date. Set the desired value and hold both the UP and DOWN arrows for 3
seconds. The ‘UP’ sign will flash a few times on the display, indicating the
upload was successful
Verifying the stored service interval and service date
- Turn the ignition key off, wait at least 5 seconds then turn on again. Make sure the engine stop switch is in the RUN position and the gearbox is in Neutral.
- Scroll through the menu of the bike’s instrument panel to the SERVICE menu. There you find both the service distance and the service date.
- If the desired value is shown, disconnect the MM tool. Otherwise, repeat the process.
- If the speedometer was in MPH reading before the procedure, change the indication in the dash menu back from Km/h to MPH
www.healtech-electronics.com/MM
FAQ
Q: How do I know if my Triumph motorcycle is compatible with the Maintenance Mate?
A: Check the part number on the packaging and use the Product Advisor on HealTech Electronics website for compatibility verification.
Q: Can I clean the unit with detergents?
A: No, only clean with water using a wet sponge to avoid scratching the front face of the unit.
Q: What is the warranty period for the Maintenance Mate?
A: HealTech Electronics Ltd. offers a two-year warranty against defects starting from the purchase date indicated on the invoice.