HealTech Electronics ESE-SW-BM1 Switchable Exhaust Servo Motor Eliminator User Manual
- June 15, 2024
- HEALTECH ELECTRONICS
Table of Contents
HealTech Electronics ESE-SW-BM1 Switchable Exhaust Servo Motor Eliminator
Product Information
Specifications
- Product Name: HealTech Electronics Switchable Exhaust Servo Eliminator module
- Model: ESE-SW-BM1
- Compatibility: BMW motorcycles with an exhaust valve and servo motor
Installation
Before installing this product, please make sure you have the correct part for your bike. Check the part number on the packaging and use the Product Advisor on our website to verify compatibility.Disclaimer: Do not attempt to install the product if you do not have basic mechanical skills. HealTech Electronics Ltd. and its distributors will not be liable for any loss or damage caused by improper installation. If you are unsure, please consult with your dealer. The Plug ‘n Go connector makes installation quick and easy, eliminating the need to alter the bike’s original wiring.
To install the ESE-SW module:
-
Locate the stock exhaust servo motor.
-
Unplug the connector of the servo motor.
-
Connect the ESE-SW module connectors in-line with the servo motor connector.
-
Secure the unit well with the supplied Velcro strips.
-
Use the supplied cable ties to fasten the wiring harness to a
solid part of the bike. -
Connect the 2-pole plug of the remote switch. Route the harness towards the front end of the bike and secure the remote switch with the supplied cable ties.
Note: You can change the supplied switch with any type of ON/OFF switch if desired.
Operation
Switch in OFF position: The LED color on the module is GREEN. This is the factory mode. The exhaust valve is controlled by the ECU normally. If there’s a problem with the exhaust valve or theservo motor, the dashboard will show the error as usual. Attention: Always have the switch in the OFF position on public roads. Otherwise, your bike’s noise emission level may beincreased, which might violate local emissionnorms/regulations. Switch in ON position: The LED color on the module is RED. Inthis mode, the exhaust valve is kept in the fully open position. If there’s a problem with the exhaust valve or the servo motor, thedashboard will NOT show the error (if a servo error was registeredpreviously, the FI light may stay ON for the next 3-5 rides). Note: You can toggle the switch to change operation mode even while riding.
Warranty
The unit is completely sealed and epoxy encapsulated, providing extreme protection for the internal parts from shocks, vibrations, and water. To ensure trouble-free operation from the start, all units have been extensively tested prior to shipment. Our dealers offer a 30-day money-back guarantee on HealTech products. You willreceive a full refund if the product does not fulfill your expectations (all parts must be returned in original condition).
FAQ
Q: Can I install this module on any BMW motorcycle?
A: No, this module is only compatible with BMW motorcycles that have an exhaust valve and servo motor. Please check compatibility before purchasing.
Q: Can I use a different switch instead of the supplied one?
A: Yes, you can change the supplied switch with any type of ON/OFF switch if desired.
Q: Can I change the operation mode while riding?
A: Yes, you can toggle the switch to change the operation mode even while riding.
Switchable exhaust servo motor eliminator module
Foreword
Congratulations on your purchase of a HealTech Electronics Switchable Exhaust Servo Eliminator module (ESE-SW). This unit will fit BMW motorcycles which have an exhaust valve and servo motor. The Plug ‘n Go connector makes installation quick and easy, eliminating the need to alter the bike’s original wiring. You have the option to control the exhaust valve operation with the switch supplied.
Installation
Before installing this product, please make sure you got the right part for
your bike. See the part number on the packaging and use the Product Advisor on
our website to check compatibility. These instructions are applicable to a
wide range of motorcycles and describe the main install steps needed for a
successful installation. You can find motorcycle specific Supplementary
Manuals on our website. Please visit:
www.healtech-electronics.com/ESE-SW
Disclaimer : Do not attempt to install the product if you don’t have
basic mechanical skills. HealTech Electronics Ltd. and its distributors shall
not be liable for any loss or damage caused by improper installation. If in
doubt, please consult with your dealer.
Follow these steps:
- Locate the stock exhaust servo motor.
- Unplug the connector of the servo motor.
- Connect the ESE-SW module connectors in-line with the servo motor connector.
- Secure the unit well with the supplied Velcro strips. Use the supplied cable ties to fasten the wiring harness to a solid part of the bike.
- Connect the 2-pole plug of the remote switch. Route the harness towards the front end of the bike and secure the remote switch with the supplied cable ties.
Note: If you wish, you may change the supplied switch per your liking (any type of ON/OFF switch can be used).
Operation
Switch in OFF position:
The LED color on the module is GREEN. This is the factory mode. The exhaust
valve is controlled by the ECU normally. If there’s a problem with the exhaust
valve or the servo motor, the dashboard will show the error as usual.
Attention: Always have the switch in the OFF position on public roads.
Otherwise, your bike’s noise emission level may be increased which might
violate local emission norms/regulations.
Switch in ON position:
The LED color on the module is RED. In this mode, the exhaust valve is kept in
the fully open position. If there’s a problem with the exhaust valve or the
servo motor, the dashboard will NOT show the error (if a servo error was
registered previously, the FI light may stay ON for the next 3-5 rides).
Note: You can toggle the switch to change operation mode even while
riding.
Warranty
The unit is completely sealed and epoxy encapsulated, which gives extreme protection for the internal parts from shocks, vibrations and water. To ensure trouble-free operation from the start, all units have been extensively tested prior to shipment. Our dealers are offering a 30-day money-back guarantee on HealTech products, thus you will get your money back if the product does not fulfill your expectations (all parts must be returned in original condition for full refund). Furthermore, the product is covered by our 2-year replacement warranty from the date of purchase.
Specifications
- Supply voltage: +5V to +16V
- Max. supply current at 12V: 130 mA
- Operating temp: -40°C to +80°C (-40°F to +176°F)
- Waterproof: IP68
- Size: 50 x 30 x 17mm (1.9 x 1.2 x 0.6 inches)
- Weight: 45g (1.58 oz)
ESE-SW-BM1 User Manual [rev. 001] | www.healtech-electronics.com/ESE- SW
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>