Azfenro A04969W3 22 In 3 Light Polished Gold LED Contemporary Vanity Light Bar Instruction Manual

Azfenro A04969W3 22 In 3 Light Polished Gold LED Contemporary Vanity

Light Bar

Product Information

Specifications

• Item Number: A04969W3
• Voltage: 120V
• Max Wattage: Type B, Max 40W per bulb

Product Usage Instructions

Warning:
To reduce the risk of fire, electric shock, or personal injury, please follow these instructions:

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

Mounting:
Follow these steps to mount the product:

4. Ensure that the mounting surface is clean, dry, flat, strong enough, and 1/4 larger than the canopy on all sides.
5. Correct any gaps between the mounting surface and canopy exceeding 3/16 as required.
6. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

Electrical Requirements:
Ensure the following electrical requirements are met:

7. Make sure the voltage you are using is 120V.
8. The maximum wattage is Type B, Max 40W per bulb.

Bulb Replacement:
Follow these steps to replace bulbs:

8. Turn off or unplug the lamp.
9. Wait until the lamp is cool, as bulbs get hot quickly.

**Safety Instructions

**

It must be understood that common sense, caution, and care must be used with any electrical products. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur.

Frequently Asked Questions (FAQ)

Q: What tools are required for assembly and installation?

A: The following tools are required (NOT INCLUDED):

• Ladder
• Philips Head or Flat Blade Screwdriver
• Electrical Tape
• Pliers
• Wire Cutter/Stripper

Q: What parts are included?

A: The following parts are included:

• (C) Green ground screw (1)
• (D) Mounting plate (1)
• (E) Backplate (1)
• (F) Knob nut (2)
• (G) Bracket (3)
• (H) Glass shade (3)
• (I) Washer (6)
• (J) Nut (6)

Q: What accessories are enclosed?

A: The following accessories are enclosed:

• (A) Mounting screw (2)
• (B) Plastic wire connector (3)
• (I) Washer (2) (spare part)
• (J) Nut (1) (spare part)

Q: How do I assemble and install the product?

A: Follow these steps:

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
2. Turn off power. Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
3. Secure mounting plate (D) to the outlet box with mounting screws (A).
4. Connect wires as shown in the wires connection chart. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Wires Connection Chart: Connect wires according to the below chart:

with copper conductor
Clear, Brown, Gold or Black with tracer| Insulated wire(other than green) with silver conductor

Note : When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

Item Number: A04969W3

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instructions carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

   • » Go to the main fuse, or circuit breaker, box in your home.
     Place the main power switch in the “OFF” position.

   • » Place the wall switch in the “OFF” position.

4. The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is Type B, with a max of 40W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT:

TOOLS REQUIRED
(NOT INCLUDED):

PARTS INCLUDING

• (C) Green ground screw (1)
• (D) Mounting plate (1)
• (E) Backplate (1)
• (F) Knob nut (2)
• (G) Bracket (3)
• (H) Glass shade (3)
• (I) Washer (6)
• (J) Nut (6)

ACCESSORIES ENCLOSED:

• (A) Mounting screw (2)
• (B) Plastic wire connector (3)
• (I) Washer (2) (spare part)
• (J) Nut (1) (spare part)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off the power. Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • » Go to the main fuse, or circuit breaker, box in your home.
     Place the main power switch in the “OFF” position.

   • » Place the wall switch in the “OFF” position.

3. Make assembly

• Step A1 »
  Unscrew knob nuts (F) from the back plate (E) and mounting plate (D), then set them aside for later installation.

• Step A2 »
  Carefully pass the supply wires from the outlet box through the mounting plate (D). Secure mounting plate (D) to the outlet box with mounting screws (A).

• Step A3 »
  Make wire connections. Connect wires as below wires connection shown below.

PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the below chart

Connect wires according to the below chart

• Note : When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

Step A4 »

• Align the holes in the back plate (E) with the pre-assembled mounting screws, then attach the back plate (E) to the mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.

NOTE: back plate (E) should be snug against the wall with knob nuts (F). If not, remove the back plate (E), and adjust the threaded length of pre- assembled mounting screws on the mounting plate (D):

• Unscrew the pre-assembled hex nuts.
• Screw the pre-assembled mounting screws in or out of the mounting plate (D).
• When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.

Step A5 »

1. Remove nuts (J) from brackets (G).
2. Align nuts (J) with the holes on brackets (G).
3. Screw nuts (J) into holes on brackets (G) with washers (I) to secure glass shades (H) as shown in the illustration.
4. Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

Check everything is installed properly, then you can turn on the light. Enjoy!

ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

CLEANING

1. To clean, wipe the fixture with a soft cloth.
2. Clean glass with a mild cleaner (such as mild and non-abrasive soap).
3. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>