BRAYER BR4851 Fan Heater Instruction Manual

: June 4, 2024
: BRAYER

Table of Contents

BRAYER BR4851 Fan Heater
DESCRIPTION
SAFETY MEASURES AND OPERATION RECOMMENDATIONS
BEFORE THE FIRST USE
CLEANING AND MAINTENANCE
TECHNICAL SPECIFICATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BRAYER BR4851 Fan Heater

A fan heater is intended for use as an additional heating unit, for heating of small amenity room or its certain area.

DESCRIPTION

Base
Air grid
Control panel
Body
Power switch «I/0»
Control panel (3)
On/off button
Timer on/off button
Operation mode icons row
Operating mode selection button
Temperature/timer operation time digital symbols
Body oscillation on the button
Remote control (17)
On/off button
Operating mode selection button
Timer on/off button
Body oscillation on button
Temperature setting buttons
Remote control
Battery holder

ATTENTION!

Portable fan heaters are intended for use as additional heating units, for heating small amenity rooms or a certain area. They are not intended for use as main heating units.
For additional protection, it is reasonable to install a residual current device (RCD) with a nominal operating current not exceeding 30 mA. To install an RCD, contact an electrical technician.

SAFETY MEASURES AND OPERATION RECOMMENDATIONS

Read the operation manual carefully before using the fan heater; after reading, keep it for future reference.

Use the unit for its intended purpose only, as it is stated in this manual.
Mishandling the unit can lead to its breakage and cause harm to the user or damage to the user’s property, which is not covered by the warranty.
ATTENTION!
A lithium battery is used in the remote control. To avoid danger, do not allow children to play with the battery. If your child has swallowed a battery, immediately see a doctor.
Make sure that the operating voltage of the unit indicated on the label corresponds to your home mains voltage.
The power cord of the fan heater is three-wire with a ground cord, and the power plug has a ground contact. Always connect the power plug to the socket with reliable grounding contact. In case of any inner short circuit, grounding reduces the risk of electric shock, because the current will pass through the ground wire.
To avoid fire, do not use adapters for connecting the unit to the mains.
To avoid mains overloading, do not switch on several electrical appliances with high power consumption at the same time.
If you use an extension cord, make sure that the wire section of the extension cord and the wire section of the power cord of the fan heater match.
Place the fan heater vertically on a flat dry moistureand heat-resistant surface, do not place it horizontally and do not turn it over.
Do not place the fan heater on soft surfaces, such as carpets with high pile, sofas or beds.
The distance between the front grid of the fan heater and the furniture should be at least 1,0 m.
Do not use the fan heater in a limited space, for example, in built-in cabinets or wall niches.
Do not use the power cord as a carrying handle for the fan heater.
Do not wind the power cord around the fan heater body.
Provide that the power cord does not contact with hot surfaces and sharp furniture edges.
Protect the unit from impacts, falling, vibrations and other mechanical stress.
Avoid blocking the air inlet grid of the fan heater with foreign objects, do not cover the unit during the operation.
Do not use the unit in places where inflammable liquids are used or aerosols are sprayed, do not use the unit in the places where such liquids are stored.
Do not use the unit near heating appliances, heat sources or open flame.
Do not use the unit outdoors, in bathrooms or in places with high humidity.
Do not use the unit in proximity to the kitchen sink, near swimming pools or other containers filled with water.
If the unit is dropped into water, unplug it immediately, and only then you can take the unit out of water. Apply to the authorized service center for testing or repairing the unit.
Do not touch the unit body, the power cord and the power plug with wet hands.
It is not recommended to use the unit during lightning storms.
Do not block and do not insert any foreign objects into the air outlets.
During the operation the fan heater grid becomes very hot, do not touch it to avoid getting burns.
Avoid getting burns by hot air.
Never leave the unit connected to the mains unattended.
Unplug the unit after usage or before cleaning.
Switch the fan heater off and unplug the power cord plug from the mains socket.
When unplugging the unit, hold the power plug and carefully remove it from the mains socket, do not pull the power cord, as this can lead to its damage or cause a short circuit.
Do not immerse the unit into water or any other liquids.
If water droplets fall on the fan heater body, switch it off and disconnect the power plug from the mains before touching the unit, then wipe the fan heater body with a dry cloth.
For child safety reasons do not leave polyethylene bags used as packaging unattended.
ATTENTION!
Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!
The unit is not intended for usage by children.
Do not leave children unattended to prevent using the unit as a toy.
Do not allow children to touch the operating surface, the unit body, the power cord or the power plug during operation of the unit.
Be especially careful if children or disabled persons are near the operating unit.
During the unit operation and breaks between operation cycles, place the unit out of reach of children.
The unit is not intended for usage by physically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
From time to time check the power cord integrity.
If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.
If foreign smell or noise appear, stop using the unit immediately.
Do not repair the unit by yourself. Do not disassemble the unit by yourself, if any malfunction is detected, and after the unit was dropped, unplug it and apply to the service center.
To avoid damages, transport the unit in the original package.
Keep the unit in a dry cool place out of reach of children and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE UNIT FOR COMMERCIAL OR LABORATORY PURPOSES.

BEFORE THE FIRST USE

After the unit’s transportation or storage at negative temperature, unpack it and wait for at least 3 hours before using it.

Unpack the unit and remove all the packaging materials.
Keep the original package.
Read the safety measures and operating recommendations.
Check the delivery set.
Examine the unit for damages, in case of damage do not plug it into the mains.
Make sure that specified specifications of power supply voltage of the unit correspond to the specifications of your mains. When the unit is powered from the mains with 60 Hz frequency, it does not need any additional operations.
Wipe the fan heater body with a slightly damp cloth and then wipe it dry.

USING THE FAN HEATER

Place the fan heater base (1) on a flat, dry and steady surface.
Do not place the fan heater on soft surfaces, such as carpets with high pile, sofas or beds.
The distance between the front grid of the fan heater and the furniture should be at least 1,0 m.
To avoid mains overloading, do not switch on several electrical appliances with high power consumption at the same time.

Remote control (17)

ATTENTION!
A lithium battery is used in the remote control. To avoid danger, do not allow children to play with the battery. If your child has swallowed a battery, immediately see a doctor.

Battery installation/replacement (pic. 1)

Press on the clamp and remove the battery holder
(18) from the remote
control (17) body, insert a CR2025 battery (not
supplied with the unit) into the holder, strictly
following the polarity.
Install the battery holder (18) into the remote control
(17).
Notes:
- replace the battery in time;
- do not recharge the lithium battery;
- remove the battery if you are not planning to use the unit for a long time;
- remove the used battery from the remote control (17) and dispose of it.

Switching the fan heater on

Insert the power plug into the main socket.
Switch the fan heater on by setting the power switch (5) to position «I», the room temperature will be displayed with the digital symbols (10) on the control panel (3).
Note: — the temperature digital indications (10) may be slightly different from the readings of another thermometer.
Switch the fan heater on by pressing the on/off button (6) on the control panel (3) or the button (12) on the remote control (17).
Select the operation mode by pressing the button (9) on the control panel (3) or the button(9) on the remote control (13).
The operation modes are displayed in the operation mode icons row (8) « » on the control panel (3).
- room ventilation mode;
- low power level for heating small rooms;
- the high power level for heating large rooms.
Note: — when you switch the unit on for the first time in the heating mode, some smoke or foreign odor may appear. It is normal and not covered by a warranty

Fan heater oscillation mode

Press the button (11) « » on the control panel (3) or the button (15) « » on the remote control (17) to switch the body oscillation mode on, the symbol « » will appear on the control panel (3). To switch the oscillation mode off, press the button (9) « » again, the symbol « » on the control panel (3) will go out.

Timer setting

Press the timer on/off button (7) « » on the control panel (3) or the button (14) « » on the remote control (13) and set the requited timer operation time.
Time setting range is up to 12 hours.
The timer operation time is indicated with the digital symbols (10) on the control panel (3).
To switch the timer off, consequently press the button (7,14) « » until the digital symbols (10) show the room temperature.

Room heating temperature setting

ATTENTION! You can set the room heating temperature only with the remote control (17).

Press the buttons (16) « » on the remote control (17) to set the required room heating temperature.
The temperature setting range is from 15 to 47 degrees, the temperature is displayed on the control panel (3) with digital symbols (10).
Switching the fan heater off
Switch the fan heater off by pressing the on/off button (6) « » on the control panel (3) or the button (12) « » on the remote control (17).
Note: — after pressing buttons (6,12), the heating element will switch off, but the fan will continue to operate for 30 seconds to cool the heating element.
After the fan stops, switch the power off by setting the switch (5) to the position «0».

AUTOMATIC EMERGENCY SWITCH-OFF FUNCTION IF THE OUTGOING AIR IS TOO HOT

If the outgoing air temperature exceeds the acceptable value, the automatic thermal switch will switch on, and the fan heater will be switched off.
Set the power switch (5) to the position «0» and unplug the unit, let the fan heater cool down for approximately 15-25 minutes (depending on the air temperature in the room) and only after that you can switch the unit on again.
Make sure that the front (2) and rear grids are not blocked with foreign objects.
Insert the power plug into the mains socket and switch the fan heater on.
If the fan heater does not switch on, it may be caused by another malfunction. In this case apply to a service center for repair of the fan heater.

PROTECTION FROM DROPPING

If the fan heater accidentally falls or tilts too much, the fall protection device will switch on and the fan the heater will be switched off.
Set the fan heater into a vertical position, and the unit will resume operation.
Note: — place the fan heater on a flat dry and steady surface to prevent it from dropping.

CLEANING AND MAINTENANCE

Before cleaning the fan heater set the power switch (5) to the position «0», and make sure that the power plug is not inserted into the mains socket.
Wipe the fan heater body (4) with a slightly damp cloth and then wipe it dry.
Do not use liquid detergents, abrasive cleaners and any solvents to clean the fan heater.
To avoid the risk of electric shock provides that no water or other liquid gets into the fan heater body.
To clean the air grids, use a vacuum cleaner with a corresponding attachment.

STORAGE

After cleaning put the fan heater away for storage in a dry cool place away from children and disabled persons.
Before using the fan heater next time, it is recommended to check the unit operability and integrity of the power cord isolation and the power cord plug.

DELIVERY SET

Fan heater — 1 pc.
Remote control — 1 pc.
Instruction manual — 1 pc

TECHNICAL SPECIFICATIONS

Power supply: 220-240 V, ~ 50/60 Hz
Rated input power: 1500 W
Heating area: 15 m²
Remote control: 3 V — «CR2025» battery (not included)

RECYCLING
To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after the expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, take the unit and the batteries to specialized stations for further recycling. The waste generated during the disposal of products is subject to mandatory collection and consequent disposal in the prescribed manner.

For further information about recycling of this product apply to a local municipal administration, a household waste disposal service or to the shop where you purchased this product. The manufacturer reserves the right to change the design, structure, and specifications not affecting the general operation principles of the unit, without prior notice.
The unit operating life is 3 years
The manufacturing date is specified in the serial number. In case of any malfunctions, it is necessary to apply promptly to the authorized service center.

https://tm.by
MHTepHeT-MarasnH TM.by