beko BFTK30100SS 72 Built In Trim Kit Instruction Manual

Table of Contents

beko-BFTK30100SS-72-Built-In-Trim-Kit-PRO

Specifications

Model: BFTK30100SS
Dimensions: 72″ Tall, 61.75″ Wide, 25.625″ Depth
Tools Required: Drill with Phillips Tip or Phillips Screwdriver, 1/8 Drill Bit
Installation: Requires 2 people

Step 1: Preparing the Fridge Units

Remove any plastic hole caps on top of the fridge units within 1 inch of the doors. Ensure the top of the fridge units is clean and dust-free.

Step 2: Installing the Beko Fridge Joining Kit

Install the Beko Joining Kit (Part #: 6161530100) as per the joining kit installation instructions before proceeding further.

Step 3: Installing L Angle Trim (C)

Dry fit the L Angle Trim (C) on top of the units with the outside facing towards you. The trim should be flush with the front of the fridge when the doors are open.

Step 4: Attaching L Angle Trim (C)

Peel the film from the Foam Tape on the bottom of L Angle Trim (C) and firmly press it onto the top of the fridge units to adhere them together.

Step 5: Installing Top Trim (B)

Dry fit the Top Trim (B) centered under the top of the cabinet opening. Mark hole placements with a writing utensil, then drill pilot holes using a 1/8 drill bit.

Step 6: Attaching Top Trim (B)

Step 7: Finalizing Installation

Push the paired fridge units into the center of the cabinet space for a complete installation.

FAQ

Q: Can I install the trim kit by myself?

A: No, it is recommended to have 2 people for certain steps during the installation process to ensure proper alignment and secure attachment.

Q: What are the dimensions required for installing this trim kit?

A: The opening must be at least 72″ tall, 61.75″ wide, and 25.625″ or greater in depth to accommodate both the fridges and the trim kit.

PARTS BAG 26137 Beko – 30” Fridge Trim Kit

PART Quantity Reference
- Screws 8 (2 extra) A
TOOLS REQUIRED: Drill with Phillips Tip, or Phillips Screwdriver, 1/8” Drill Bit
2 People Required for Assembly

PART Quantity Reference
- Top Trim 1 B
- L Angle Trim 1 C
NOTE: The Beko Joining Kit must be installed before the Trim Kit Installation
Ensure the location for your fridges has an opening that is 72” Tall, 61.75” Wide, and 25.625” or greater Depth to house fridges and trim kit.

beko-BFTK30100SS-72-Built-In-Trim-Kit-FIG-3

If present, remove any plastic hole caps on top of the fridge units within 1 inch of the doors. Make sure the top of the fridge units are clean and dust-free.
Beko Fridge Joining Kit, per fridge, joining kit installation instructions, must be installed before the next step.
- Joining Kit Part #: 6161530100
Open fridge doors. Dry fit L Angle Trim (C) on top of units. Make sure to have the outside of L Angle Trim (C) facing toward you. L Angle Trim (C) should be flush with the front of the fridge when doors are open.
After making sure L Angle Trim (C) fits, peel film from Foam Tape on the bottom of L Angle Trim (C), and apply to the top of fridge units. Press firmly to adhere L Angle Trim (C) to fridge units.
- NOTE: Have 2 people for steps 5 & 6
Dry fit Top Trim (B), centered, under the top of the cabinet opening. The front of the Trim should be flush with cabinetry, Not cabinet doors.
- Mark hole placement with a writing utensil. Remove Top Trim (B) then use a drill with 1/8” bit to pilot (6) holes into the cabinet.
Use (6) Screws (A) to attach Top Trim (B) to the cabinet.
Push paired fridge units into the center of the cabinet space.