ULTRALINK ULM202USB High Performance 2.4 GHz Digital Wireless System 2 Handheld Microphones User Guide

ULTRALINK ULM202USB High Performance 2.4 GHz Digital Wireless System 2

Handheld Microphones

Safety Instruction

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install by the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Use only attachments/accessories specified by the manufacturer.
10. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
11. Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection centre licensed for the recycling of waste electrical and electronic equipment (EEE).
12. The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office or your household waste collection service.
13. Do not install in a confined space, such as a bookcase or similar unit.
14. Do not place naked flame sources, such as lighted candles, on the apparatus.

WARNING

• As with all small batteries, the batteries used with this product should be kept away from small children who still put things in their mouths. If they are swallowed, promptly call your local poison control centre.
• Always purchase the correct size and grade of battery most suitable for the intended use.
• Replace all batteries of a set at the same time.
• Clean the battery contacts and also those of the device before battery installation.
• Ensure the batteries are installed correctly concerning polarity (+ and -).
• Always remove the battery if consumed or if the product is to be left unused for a long time.
• Replacement of a battery with an incorrect type that can defeat a safeguard! Replace only with the same or equivalent type!
• Risk of fire or explosion if the battery is replaced by an incorrect type.
• Disposal of a battery into a fire or a hot oven, or mechanically crushing or cutting off a battery, which can result in an explosion;
• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas, and A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
• Attention should be drawn to the environmental aspects of battery disposal.

ULM202USB/ULM200USB

Controls

ULM202USB/ULM200USB Controls

1. POWER/STATUS LED
2. ▼ VOLUME Button (Mute/volume down)
3. ▲ VOLUME Button (Power on/unmute/volume up)
4. USB connector
5. Wireless Link Status LED

ULM202USB/ULM200USB Getting Started

1. Connect the ULM200D wireless receiver to the “WIRELESS ONLY!” USB connector on wireless-enabled Behringer mixers, powered speakers or other compatible products, or to a USB port on a computer.

2. Press and hold the ▲ button on the ULM200M wireless microphone to connect wirelessly to the ULM200D receiver. The LED on the microphone will flash slowly during the connecting sequence and will light solid once connected.
   If the ULM200M wireless microphone cannot connect to a receiver, the microphone will automatically power down after 10 seconds.

3. Once connected, the ULM200M microphone will be set at a medium volume. Use the ▲ and ▼ buttons to adjust the volume

4. A long press of the ▼ button will put the ULM200M microphone into mute. The mute condition is indicated by the rapid flashing of the LED. If the user does not unmute within 60 seconds, the ULM200M microphone will power down to save battery life.

5. A short press of the ▲ button will unmute the ULM200M microphone. If the ULM200M microphone is unmuted more than 10 seconds after muting, it will return to the previous volume level, if unmuted after less than 10 seconds it will be set to the minimum volume level.

6. Unplug the ULM200D wireless receiver to power down. The ULM200M wireless microphone will power down for 10 seconds after the ULM200D wireless receiver is unplugged.

7. The LED in the ULM200M wireless microphone will indicate when the battery is low by regular brief flashes.

8. Should the ULM200M wireless microphone become unpaired with the ULM200D wireless receiver, the microphone can be repaired from the powered-down state by simultaneously pressing the ▲ and ▼ buttons and moving the microphone to within 10 cm (4 inches) of the ULM200D wireless receiver. The LED on the microphone will flash slowly during the pairing sequence and will light solid once connected. If the ULM200M wireless microphone cannot pair to the receiver it will automatically power down after 10 seconds.

Specifications

• RF output <20 dBm (100 mW)
• Operating range 120 m (Line of Sight)*
• Dynamic range 92 dB, A-weighted**
• Equivalent input noise -112 dBu
• Frequency Response 20 Hz – 20 kHz, ±1 dB** (Wireless Link)
• Sampling rate 48 kHz
• Resolution 24-bit
• Encoding 232 kbps SLAC
• (Slightly Lossy Audio Codec)
• Latency 14.5 ms
• RF frequency 2.4 GHz ISM band
• (2406 MHz – 2474 MHz), 18 channels
• USB current consumption 70 mA @ 5 VDC
• Battery type 2 x AA (LR6) Alkaline cells
• Battery life 30 hours
• Dimensions (W x D x H) 45.7 x 45.7 x 243.8 mm (1.8 x 1.8 x 9.6″)
• Weight ULM200USB 0.2 kg (0.4 lbs)ULM202USB 0.4 kg (0.9 lbs)

The achievable range will be dependent on nearby sources of RF interference and/or line-of-sight obstacles. Measured from analog input to analog output, unity gain operation without wireless compression.

LEGAL DISCLAIMER

Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. Music Tribe Global Brands Ltd.2023 All rights reserved.

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at community.musictribe.com/pages/support#warranty

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

Responsible Party Name: Music Tribe Commercial NV Inc.
Address: 122 E. 42nd St.1,
8th Floor NY, NY 10168, United States
Email Address: legal@musictribe.com
FCC ID: QWHULM200D01, QWHULM200M01
ULTRALINK ULM202USB/ULM200USB

This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Important information
Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

Hereby, Music Tribe declares that this product complies with Directive 2014/53/EU, Directive 2014/30/EU, Directive 2014/35/EU,
Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU,
Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Gammel Strand 44, DK-1202 København K, Denmark
UK Representative: Music Tribe Brands UK Ltd.
Address: 8th Floor, 20 Farringdon Street London EC4A 4AB, United Kingdom

References

• Music Tribe
• Music Tribe
• Music Tribe
• Music Tribe
• Music Tribe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>