CO-Z HS-E550BLK Airbrush Spray Booth User Manual

June 1, 2024
CO-Z

CO-Z HS-E550BLK Airbrush Spray Booth User Manual
CO-Z HS-E550BLK Airbrush Spray Booth

Safety Information

Warning

  • ONLY assemble and use this device in accordance with these instructions and for its intended purpose. DO NOT allow unsupervised use by children, by anyone who has not read these instructions, or by any person whose mental or physical condition precludes safe use.
  • ALWAYS keep your work area clean and well lit. Cluttered and dark areas invite accidents.
  • Make sure your worksite is well ventilated. For work in confined spaces, ALWAYS connect this device to the outdoors using the exhaust hose and wear proper breathing protection such as a respirator to prevent accidental inhalation of carcinogenic paint particles or other debris. If becoming nauseous or disoriented, stop work, turn off this device and any other electrical appliances for your work, and leave the area. Also don appropriate hand protection during assembly and eye protection during work.
  • ONLY place this device on even, stable, and nonslip surfaces. NEVER use this device in the presence of any flammable, explosive, or corrosive liquids, gases, or dust.
  • ONLY use this device with stable and compatible power sources. DO NOT modify the power plug or move this device by pulling on its power cord. In case of power loss during operation, unplug this device IMMEDIATELY until power is restored.
  • DO NOT allow any electrical components to become wet or operate this device with wet hands or in highly humid environments. If any electrical component becomes wet accidentally, disconnect this device from power and allow time for it to dry completely before further use.
  • DO NOT leave this device unattended while it is in operation.
  • ALWAYS disconnect this device from power before performing any inspection, cleaning, maintenance, or repair.
  • DO NOT operate this device if it is damaged or shows signs of malfunction. Repair or replace problematic components before further use. NEVER replace any parts with nonidentical ones

Specifications

Model HS-E550BLK
Power Adapter Input
Output 12V 5A DC
Rated Power 45.6 W
Max. Noise Level 53 dB
Optimal Operational Temp. Range 41–104°F
LED Lighting Max. Power
Max. Brightness 2340 lm
Exhaust System Number of Fans
Max. Power 36.2 W
Max. Air Flow 141 cfm
Max. Velocity 29.5 fps
Exhaust Hose Length Range 2.3–5.6 ft.
Turntable Diameter 7.5 in.
Base Board Internal Size 19.9×13 in.
Filter Composition
Total Size 15.7×7.3×1.1 in.
Dimensions Folded
Unfolded 21.7×18.8×14.1 in.
Net Weight 12.1 lb.

Product Diagram

Product Diagram

Package List

Package List

Item Name Qty.
A Main Body 1
B Exhaust Hose 1
C Nozzle 1
D Sleeve with Hose Clamp 1
E Right Light Tube (“R”) 1
F Top Light Tube 1
G Left Light Tube (“L”) 1
H Left Bottom Tube (“L”) 1
I Right Bottom Tube (“R”) 1
J Turntable 1
K Power Adapter 1
L Power Cord 1

Not Included but Helpful:

  • Phillips Screwdriver

Assembly

Wear hand protection during assembly to avoid accidental injury.

  1. Open the packing box and take out the nozzle (C), top light tube (F), and turntable (J) directly. Remove the main body (A) of this device from the box using its carrying handle and then disconnect the remaining packaging.

  2. Lay the main body horizontally on a firm, level, and nonslip surface, allowing its base board to face upward. Open this board and take the remaining items listed in Package List out of the booth.
    Assembly Instruction

  3. Lift the main body right side up as shown.
    Assembly Instruction

  4. Unfold the left and right boards. Insert the plugs of the left and right bottom tubes (H & I) into the sockets beside the filter’s lower corners, pressing until they are locked into place.
    Note: The two bottom tubes ARE different and should NOT be mixed up. The left tube is marked with an L and the right with an R.
    Assembly Instruction

  5. Flip up the dual top board. Connect the side boards to its back part by inserting their tabs into the slots as shown
    Assembly Instruction

  6. Fit the top light tube onto the left and right boards, ensuring its side tabs are well seated in the slots at the top of these side boards. Flip down the top board’s front part and secure it to the top light tube and side boards using their tabs and slots as shown.
    Assembly Instruction

  7. Connect the right light tube (E) to the top light tube and right bottom tube using its plugs as described in Step 4. Install the left light tube (G) in the same fashion.
    Note: The two LED light tubes are NOT interchangeable. The left tube is marked with an L and the right with an R.
    Assembly Instruction

  8. Extend the exhaust hose (B) as needed. Attach the nozzle and sleeve (D) to the hose, screwing them into place.
    Assembly Instruction

  9. Place the sleeve over the vent and secure it using the attached hose clamp.
    Assembly Instruction

  10. Extend the exhaust hose as needed again and place the nozzle to an appropriate location (out of a window if using this device indoors)

  11. Set the turntable onto a convenient position on the base board, usually the center of the dual base for best results.
    Assembly Instruction

  12. Connect the power cord (L) to the power adapter (K) and then connect this adapter to the power inlet on this device. Being sure the light and fan knobs are turned completely counterclockwise, connect the power cord to a stable and compatible power source.
    Assembly Instruction

Operation

Make sure that everything has been correctly installed.

  1. Turn the light knob clockwise until hearing a click. The three LED lights should come on at their highest brightness level. To lower the brightness, continue turning the knob clockwise. To raise the brightness, turn the knob counterclockwise.

  2. Turn the fan knob clockwise until hearing a click. The exhaust fans should start working at their highest speed. To decrease the fan speed, continue turning the knob clockwise. To increase the speed, turn the knob counterclockwise.
    Operation Instruction

  3. Place your workpiece onto the turntable. Paint its external surface using your airbrush in one hand and rotate the turntable with the other hand.
    Operation Instruction

  4. When finished, stop your airbrush and the turntable. Continue running the device for at least 2 minutes to allow the exhaust system to fully discharge the remaining airborne particles.

  5. Turn both knobs completely counterclockwise to shut down the lights and fans. Then, disconnect the device from power.

Troubleshooting

Possible Problems Usual Solutions
LED Lights Not Working Check that the booth is properly plugged into a

working power source and its power adapter’s plug is firmly and fully inserted into its power inlet.
Confirm that the LED light tubes are securely connected.
Replace any problematic LED light tubes with new identical ones.
Ventilation Not Working| Check that the booth is properly plugged into a working power source and its power adapter’s plug is firmly and fully inserted into its power inlet.
Have a trained technician inspect the exhaust fans and other related internal components. Have any problematic parts repaired or replaced with new identical ones.
Inadequate Ventilation| Consider the booth’s location. For indoor use, ensure that its nozzle is placed out of a window.
Ensure that the filter, vent, nozzle, and exhaust hose are clean and unclogged. Remove any dirt or obstructions or replace the filter with a new identical one as needed.
Have a trained technician inspect the exhaust fans and other related internal components. Have any problematic parts repaired or replaced with new identical ones.
Excessive Noise or Vibration| Ensure that the booth is placed on a stable and level surface.
Have a trained technician inspect the exhaust fans and other related internal components for looseness, wear, and damage. Have any problematic parts retightened, lubricated, or replaced with new identical ones.

Maintenance

  • Turn off and unplug this device between uses and before undertaking any inspection, cleaning, maintenance, or repair.
  • After each use, remove the turntable, rinse away the remaining paint, and dry it completely with a soft cloth. Clean the boards, filter, and other external surfaces of this device with a soft damp cloth. Do not use harsh abrasives or caustic chemicals.
  • Periodically check the exhaust system of this device for any obstructions, clearing the vent, exhaust hose, nozzle, etc. using a dry brush or other similar tools as needed. Also inspect the other components for any wear, breakage, or malfunction between uses, repairing or replacing any problematic parts before further use. Only use identical parts and always fully replace any damaged electrical connections.
  • If this device is not to be used for an extended period of time, unplug, clean, and fully dry it before storing in a cool dry location inaccessible to children and away from direct light and rain.

Disposal

Electrical products should not be disposed of with household products. In the EU and UK, according to the European Directive 2012/19/EU for the disposal of electrical and electronic equipment and its implementation in national laws, used electrical products must be collected separately and disposed of at the collection points provided for this purpose. Locations in Australia, Canada, and the United States may have similar regulations. Contact your local authorities or dealer for disposal and recycling advice.

Contact Us

Thank you for choosing our products! If you have any questions or comments, contact us at
help@cs-supportpro.com and we’ll resolve your issue ASAP!

For a .pdf copy of the latest version of these instructions, use the appropriate app on your smartphone to scan the QR code to the right.
QR Code

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals