CO-Z V20230110 1 Gallon Water Distiller User Manual

: May 15, 2024
: CO-Z

Table of Contents

Setup
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CO-Z V20230110 1 Gallon Water Distiller User Manual

CO-Z V20230110 1 Gallon Water Distiller User Manual

Safety Information

Warning!

ONLY use this distiller with stable and compatible power sources.
DO NOT let children or persons with impaired physical or mental capacities operate this device without strict supervision.
DO NOT use this device when its outer casing is wet as this may lead to short circuits, fire, or electrocution.
Be careful during use as this device produces VERY hot water vapor that can cause instant scalding. Always lift the lid to the side while avoiding the escaping steam. Do not lift the lid straight up.
DO NOT use this device if its power cables are damaged in any way. Repair or replace the damaged wiring before use.
DO NOT place the bottle into a cold environment after filling it with hot distilled water as this may cause it to crack or shatter.
Disconnect the power to this device before performing any maintenance.

Specifications

CO-Z V20230110 1 Gallon Water Distiller -
Specifications

Product Diagram

CO-Z V20230110 1 Gallon Water Distiller - Product
Diagram

Package List

CO-Z V20230110 1 Gallon Water Distiller - Package List

Distiller
The distiller works by heating water into vapor and subsequently cooling it down so that it condenses back into water without its previous impurities.
Collection Bottle
This bottle collects your distilled water.
Collection Cap
This cap collects the distilled water & directs it into the bottle.
Bottle Cap
This cap seals the bottle between uses.
Activated Charcoal Filter
This filter absorbs smaller impurities that are not eliminated through distillation.
Power Cord
This cord connects any grounded (3-pronged) outlet to power the distiller’s heating element.
Chamber Cleaning Powder
This powder is used to clean the distiller, specially designed not to damage its lining.
Instruction Manual
You’re reading this.
Silicone Tube
This tube can be used to connect the distiller to another receptacle besides the provided bottle.

Setup

Bottle Assembly
Affix the handle onto the water bottle by placing one of the metal bands on the bottom groove of the bottle. Next, secure the band by placing a bolt through it and the bottom of the handle. Hand tighten the bolt with a nut. Repeat this step for the second band, affixing it to the top groove of the bottle.
To put the bottle cap onto the bottle, place the cap such that its grooves are aligned with the grooves on the bottle and turn clockwise until it is tight.

CO-Z V20230110 1 Gallon Water Distiller - Bottle
Assembly

Distiller Assembly
The silicone seal prevents water from escaping the distiller. When placing or replacing it, ensure that the rounded side is facing up.

CO-Z V20230110 1 Gallon Water Distiller - Distiller
Assembly

Remove the outlet nozzle from the lid and insert the charcoal packet into it. Reattach and secure
it onto the distiller’s lid as shown. Check that the seal remains in place.

CO-Z V20230110 1 Gallon Water Distiller - Remove the outlet nozzle from the
lid and insert the charcoal packet into it

Align the collection cap with the distiller’s spout. Optionally, use the provided silicone tubing to directly connect the spout with the bottle or another receptacle.

CO-Z V20230110 1 Gallon Water Distiller - Align the collection cap with the
distiller's spout

Operation

Open the distiller. Add water up to the maximum water level line.
Replace the top of the distiller and make sure it is properly sealed.
Plug in the power cord.
Press Reset to begin distillation cycle.
Water will begin to pour out of the distiller after about 30 minutes. It will take roughly 4 hours for a full distillation cycle to complete. Wait 10 minutes between cycles before adding water to start a new batch.
Wait 15 minutes once the distillation cycle ends before removing the lid cover. Open the lid to the side to avoid any escaping steam. Do not open the lid straight up or leave your handwhere it might be scalded.

Maintenance

Disconnect the distiller from its power source and allow it to fully cool before undertaking any cleaning, maintenance, or repair.
Rinse and wipe the tank daily using clean water. Make sure it is dry when not in use. Calcium deposits and residue can accumulate on the stainless-steel lining. Monthly cleanings are recommended. To clean the tank:

Pour in hot water until all the residue is covered.
Add 1–4 teaspoons of the provided cleaning powder, depending on the amount of residue.
Wash the inside of the distiller’s cap with a soft cloth.
Rinse these components with clean water, but do not allow any electrical component to become wet.
If there is any remaining residue, repeat this process.

CO-Z V20230110 1 Gallon Water Distiller - Maintenance

Do not use corrosive agents or steel cleaning instruments as this may damage the stainless steel lining.
Cleaning the bottle should be done with warm soapy water. Never alternate between hot and cold water as this may damage the bottle.
The silicone seal should be removed and cleaned monthly. When placing it back onto the distiller’s cap, ensure that the rounded side of the ring is placed facing up.

Troubleshooting

CO-Z V20230110 1 Gallon Water Distiller -
Troubleshooting