beko BHCP65422BBH Cooker Hood User Manual

Cooker hood
User Manual
Hota

BHCP65422BBH
185.7312. 04/R.SA/ 6.06. 2023
7702388633

BHCP65422BBH Cooker Hood

Please read this user manual first!
Dear Customer,
Thank you for purchasing t1is Beko product. We hope that you ge the best results from your product which has been manufactured with high quality and state-of-the-art technology.
Therefore, please read this entire user manual and all ather accompanying documents carefully before using the product and keep it as a reference for future use. If you handover the product to someone else, give the user manual as well. Follow all warnings and information in the usev manual.
Remember that this user manual is also applicable for several cther madels. Differences between moce s will be identified in (he manual.
Explanation of symbols
Throughout this user manual the following symbols ave used:

| Important information or useful hints about usage.
---|---
| Warning of hazardous situations with regard to life and property.
| Warning of electric shock.
| Warning of risk of fire
****| Warning of het surfaces

Arcelik A.S.
Karaagas caddesi No:2-6
34445 Sitlice/Istanbul/TURKEY
Made in TURKEY

Important instructions and warnings for safety and environment

This section contains safety instructions that will help protect from risk of personal injury or property damage.
Failure to follow these instructions shall void any warranly.
General safety

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of  xperience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Risk of Toxicating! While the appliance is operating, air in the entire house is sucked. If adequate ventilation is not provided, waste and toxic gasses which are released as a result of burning will be drawn back into the house through chimney draught.
• Do not operate the appliance together with sources that may emit toxic gasses and create air draught (wood, gas, oil, and coal stoves, water heaters, kettles, etc.).
• Always have the authorized persons check the adequacy of ventilation and chimney draught in your building.
• The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervised or instruction concerning use of the appliance by a responsible person for their safely.
• Young children should be supervised to ensure that they do not play with the appliance.Cleaning and user maintenance procedures should not be performed by the children unless they are under supervision.
• Always have the installation and repair procedures performed by Authorised Service Agent. Manufacturer shall not be held responsible for damages arising from proccdures carried out by unauthorised persons.
• Do not operate the appliance if it is defective or has any visible damage.
• Make sure that the appliance is switched off after every use.
• If the product is handed over to someone else for personal use or second-hand use purposes, the user manual, product labels and other relevant documents and parts should be also given.
• Appliance must be installed by a qualified person in accordance with the regulations in force. Otherwise, the warranty shall become void.

Electrical safety

• To get your product ready for use, firstly you must have installation place and electric wiring prepared. Later, you may call Authorised Service nearest to you.
• If it has a failure, the product should not be operated without being repaired by the Authorised Service Agent.
• There is the risk of electric shock!
• Never connect the hood before installation is completed.
• Never touch the plug with wet hands! Do not unplug by pulling from the cable; always hold by the plug to unplug.
• Product must be disconnected from the mains during installation, maintenance, cleaning and repair procedures.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
• If your product has been produced with plug, do not cut the plug to connect to electrical supply during installation. Otherwise, the warranty becomes void and the safety risks may happen for users.
• Never connect power cable near to the hobs. If melted down, cable may lead to fire.
• Any work on electrical equipment and systems may only be carried out by authorised and qualified persons.
• Incase of any damage, switch off the product and disconnect it from the mains. To do this, turn off the fuse at home.
• Make sure that fuse current is compatible with the product.
• Never wash down the product with water! There is the risk of electric shock!

Product safety

• The height between the lower surface of the hood and upper surface of the hob  should not be less than 650 mm.
• Never touch the hood’s lamp after they operated for a long time. Hot lamps may burn your hands.
• Never operate the product without oil filter. Never remove filters when the product is in use.
• Avoid big flames beneath the product. Otherwise, particles on oil filter may flame up and cause fire.
• Turn on the hobs after placing pans or pots on. Otherwise, rising temperature may deform certain parts of your product.
• Turn off the hobs before taking away pans or pots.
• Avoid inflammable materials under the hood.
• Do nol expose the product lo open flames beneath it. It can cause oils accumulated in the filter to catch fire. Do not operate the product without filter.
• Never leave the cooker unattended when frying foods, the oil may flame up and boiled oil may cause fire. Thus, be careful about cloths and curtains.
• If the hood is not periodically and properly cleaned, this may cause burning risk on your hood.
• For refreshing the kitchen’s air from cooking smells and steams, please turn on your hood for 15 minutes more after cooking or frying has ended.
• There shall be adequate ventilation of the room when the range hocd is used at the same time as appliances burning gas or other fuels. (Not applicable to appliances that only discharge the air back into the room)
• In the environment where the hood is being used, the exhaust of fuel oil or gas devices such as room heater must be absolutely insulated or device must be hermcetical type.
• If there is a fuel ail or gas device in the environment, the room must be ventilated sufficiently.
• When a non-electrically operated device is concurrently used in the environment together with the hood, the negative pressure in the room must be maximum 0.04 mbar to avoid the hood’s returning other device’s exhaust into the room.
• Never connect the hood to the chimneys used for heaters, waste gas or with rising flames. Observe authorities’ regulations on the draining of output air.
• When connecting to the chimney, use 120-mm diameter pipes. Pipe connection must be as short as possible with fewer bends.
• Do not hang easily flammable and combustible materials on hood handles.
• Our company shall never be responsible for the problems arising from the use against the warnings above.
• There is a risk of fire if cleaning Is not carried out in accordance with the instructions.
• There should be no open fire under the hood. (example: flambé)
• Caution: Accessible parts may become hot when used with a cooking appliance.
• You are recommended to clean your filter once a month in normal use.

Intended use
This product is designed for domestic use. Commercial use is not admissible.
The manufacturer shall not be liable for any damage caused by improper use or handling.
Children’s safety

• Keep children away from the product when it is operating and do not allow them to play with the product.
• Packaging materials are dangerous to children. Keep the packaging materials in a place where children cannot reach and sort and discard them in accordance with the waste disposal directives.
• Electrical products are dangerous to children. Keep children away from the product when it is operating and do not allow them to play with the product.

Disposing of the old product
Compliance with the WEEE Directive and Disposing of the Waste Product:
This product complies with EU WEEE Directive (2012/19/EU). This product bears a class fication symbol for waste electrical and electronic equigment (WEEE)
This product has been manufactured with high quality parts and materials which can be reusec anc are suitable for recycling Do not dispose of the waste p-oduct with normal domestic and cther wastes at the end of its service life. Take it to the collection center for the recycliag of electrical and electronic equiprrent. Please consult ycur local authorities to learn about these collection centers.
Compliance with RoHS Directive:
The product you have purchased camalies with EU RoHS D rective (201 1/65/EU). It does not contain harmful and oohibited materials specif ed in the Directive.
Package information
Packaging materia s of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material co lection points designated by the local authcritics.

General information

Overview

1. Hood body
2. Control aane
3. Aluminum fiter lock
4. Wande
5. Aluminum fiter
6. Lemp

Scope of delivery

Accessories supplied can vary depending on the appliance nodel.
Not every accessery cescribed in the user manual may exist on your appliance

1.  User manual

2. Wall connector
   

3. Air directing component

4. Chimney connection adapter

5. Valves to prevent reverse air flow

Technical specifications

External dimensions (height/width/depth)| min.735 mm max. 1141 mm/598 mm/502 mm
---|---
Voltage/frequency| 220-240 V ; 50 Hz
Control| 3 level
Suction power| 460 m3/h
Total power consumption| max. 200 W
Air outlet pipe diameter| 120-150 mm
LAMP
Lamp type| Led
Lamp power consumption| 2 W
Max. power of a potential replacement lamp| max.2 x 4 W.Led /max.2 x 28 W.Halogen
Voltage/frequency of lamp| 230 V∼; 50/60 Hz
Type of lamp cap| GU10
Diameter/length of lamp| 50 mm /55 mm

Technical specifications may be changed without prior notice to improve the quality of the product.
Figures in this manual are schematic and may not exactly match the product.
Values stated on the markings of the product or in other printed documents supplied with the product are obtained under laboratory conditions as per relevant standards.
Depending on operational and environmental conditions of the product, these values may vary.

Installation

Refer to the nearest Authorised Service Agent for installation of the product. Make sure that the elect‘ic installations are in place sefore calling the Authorised Service Agent to have the procuct ready for operation. If not. call a qualified electrician and fitter to have the required arrangements made.
Preparation of locat on and eleczrical installation for the product is under customer’s responsibility.
The product must be installed ir accordance with all local electrical regulations.
Prior to installation, visually check if the product has any defects on it. If so, do not “ave it installed. Damaged products cause risks for your safety.
Warning: Failure to install the screws or fixing device in accordance with the instructions may result in electrical nazards.
Installation
There should be a minimum clearance of 650 mm between the top surface of the hob and the bottom surface of the hood.
The air to be extracted via the hced skould not be connected to a chimney that is used by other appliances that use gas or other fuels. (It does not apply to devices that only blow the air back into the room)
The regulations on air exhaust should be fcllowed.
Electrical connection
Manufactured with 2-track power cable, this device must be connected to the mains by an electrical switch with at least 3mm clearance between bipolar contact leads
Have the electrical connections done by a qualified electrician.
Install your appliance so that you can reach the power connection (plug, outlet) easily after installation.
Installing the hood
Measurements are in mm.
The following provides necessary information to prepare the location for hood installation.
The heed must be installed above the central axis of the cooking aopliance. There should be 4 minimum clearance of 650 mm between the top surface of the hob and the bottam surface of the hacd. Please apply the ‘ollowing steps for the hood’s installation.

1. Centering the cooking appliance, draw an axis line on the wall up to 950mm height. Later, draw two parallel lines at 90mm distance on both sides of the axis line reaching to the ceiling. Then, determine hole locations by drawing the lines Y-J-X2 and X1 that cut vertically the axis line, for which measurements are given in Figure 1.

2. Drill eight 8-mm holes on the points X, Y, X2, X1 and place plastic plugs supplied with the packaging. Check if chimney connectors correspond to those holes or not.
   

3. As shown in Figure 2, fix connectors (C) to the holes X1 and X2 via two fixing screws supplied with the accessories. Screw distance ring (D) on the Y hole as small- diameter side facing the wall.

4. Install the hood from the key hole on back plate onto the distance ring and pull downward to make sure that it is secured. Then, screw the body onto the wall from the holes J1 and J2 on the upper back of the body. To avoid the hood falling down accidentally for any reason, screw it also from the hole J3 shown in Figure 3.

5. AS shown in Figure 4, place the chimney outlet flange (E) to the rectangular outlet on the upper part of the hood; and screw the flange onto the bedy using 2.9-mm traced screws supplied with accessories.

6. For chimney connection usage:
   In chimney-connected position, absorbed air will go through oil filters to the outlet and then will reach to the chimney though connection pipes and finally expelled from the chimney.
   When using this connection position, 150mm to 7129 mm E comestor should be installed on the chimney outlet flange as snown in Figure 5.
   Chimney connection pipes must be mace of fireproof plastic material. When using flexible connection type, it should be considered that sharp corners and sudden contractions will have a negative impact on air suction
   Te hood must ever be connected to a chimney to wich another device was already connected.
   Connection pipe should not be larger than * 20-150 mm, otherwise, proper chimney connection will be prevented.

7. Internal circulation (Use with carbon filter)
   In the position of internal circulatior, the air absorbed fron the environment will go through oil filters and carbon filters, where the smell is eliminated, and pass through air directing component. Later, it is finally sent back to tne environment through the
   grates on chimrey.
   As shown in Figure 6, air directing component Is installed on H point.
   Place ear slots of carbon filters (L) to the ears on motor carrier (M) as shown in Figure 7 and turn anti-c ockwise to fix in place. Apply the same procedure for the motor carrier on the other side.
   Failure to clean and service oil filters periodically and failure to replace carbon filters at the end of service life (approximately 4 months) may have the risk of causing fire.

8. Installation of chimney
   To install upper chimney A, secure the upper corners of the chimney on the connection (C) as shown below and screw it onto the connector with 2.9-mm screws.Distance between the hole X1 and X?2 is determined duri1g the installation process depending on the usage length of the upper chimney.
   

To install lower chimney B, stretch the chimney by pulling slightly from both sides and secure it onto upper chimney’s slots as shown in the figure above
You may use the hood in two ways:
1-Chimney-connected use
Te steam is expelled via chimney pipe which is secured to the connection ring on the hood Diameter of chimney pipe should be equal to connection ring To allow the air easily going out of the racm in horizontal arrangements, the pipe should be slightly tilted upwards (aporoximately 10°).
If the carbor filter is installed on your hood, remove it when using the hood with the chimney
2- Use with no chimney connection
Aris filtered through carbon filter and returned to the room. Cardo filter is used when there is no chimney in the house or when it is impossigie to install a chiiney pipe

• Remove aluminum filters as shown below.
  

• To install carbon filter, center the filter over the plastic parts on bath sides of far body and secure the filter in tabs

• Tighten by turning it to right and left as shown in the figure.

• Re-install aluminum filters.

Future transportation

• Keep the product’s original carton and transport the product in it. Follow the instructions 01 the carton. If you do not have the original carton, pack the product in bubble w-ap or thick cardboard and tape it securely.

Do nat plate any objects onto the product and move it in upright position.
Check the general appearance of your product fo- any damaces that might have occurred during transportation.

Operating the hoad

Hood is equipped with a motor with various speed settings.
For a better performance, we advise you to use low speeds in no-mal conditions, and high speecs when smell and vapors ave intensified.
Operating the hood

1. Off butlon
2. Speed
3. Speed
4. Speeds
5. Lamp button

1. Press on relevant buston for the soeed you want to operate <1e hood
Never press on two butlos at the same time. If pressed, higher speed will be activated
Turning off the hood

1. Press on the Off sutton when the hood is operating ir acertain speed.

Operating the lamp

1. Press on the lamp button to operate the lamp.

Turning off the lamp

1. Press on the lamp button again to turn off the lamp.
   Off button do not curn off the lamp, it only stoos operation of the hood.

Maintenance and care

General information

Service life of the product will extend and frequert problems will decrease if the product is cleaned at regular intervals.
****Disconnect the product form mains supply before starting maintenance and cleaning works.
There is the risk of electric shock!

• Clean the product thoroughly afte- each use. In this way it will be possible to remove cocking residues more easily, thus avoiding these from burning the next time the appliance is used.
• No soecial cleaning agents are required for cleaning the product. Use warn water with washing liquid, a soft cloth or sponge to clean the product and wide it with a dry cloth.
• Do not use cleaning agents that contain acid or chloride to clean the stainless or inox surfaces and the handle. use a soft cloth with a liquid detergent (not abrasive) to wipe those parts clean, paying attention to sweep in one direction.

The surface might get damaged by some detergents or cleaning materials.
Do rot use aggressive detergents, cleaning powders/creams or any sharp objects during cleaning.
Do rot use steam cleaners for cleaning.
Aluminum filter
Ths filter captures oil particles in the air. You are recommended to clean yeur filter once a nenth in normal use. Please firstly remove aluminum filters for this orocess. Wash the filters in liquid-detergent water and install them after drying. Aluminum filters might change colour in time due to wash ng. his is normal and you don’t need to replace the filter.
You can also wash aluminu filters in dishwasher.
Removing aluminum filters

1. Push aluminum filter lock forwarc.
2. Slightly lower the filter and pull forth. Otherwise, you may bend the filter.
3. After wasting, reverse the steps above to re-install the aluminum filter.

Carbon filter (Use without chimney)
Carbon filter should never be washed.
It should be replaced once every 4 months in normal use. You may obtain carson filters from the Autrorised Service
Removing carbon filters

1. Remove aluminum filters

2. To rernove carbon filter, turn it to release from the tab.
   

3. Install the new carbon filter.

4. Re-inszall aluminum filters.

You may cause fire if you do not observe the rules regarding tre cleaning and replacing hood filters.
Replacing the lamp
  The hood lamp in this product can be changed by the user.
Before replacing the lamp, make sure Ai the product is disconrected from mains in order to avoid the risk of an electrical shack. If hot, let the lamp cool down.
Hot surfaces may cause ourns!
For the specifications of tye lamp, see Technical specifications, page 10. Oven lamps can be obtained from Authorised Service Agents.
Position of lamp might vary ‘rom the figure.
The lamp used in this appliance is not suitable for household room illumination. The intended purpose of this lamp is to assist the user to see foodstuffs.
Use only with self-shielded tungsten haloge1 lamps or self-shielded metal halide lamps.

1. Remove the lamp pressing it towarcs its seat in clockwise direction (1) and then remove turning it in counterclockwise direction (2).
   

2. Insert the new lamp turning it in c ockwise cirection.

3. A “click” w Il be heard when the lamp is securec in its place.

Troubleshooting

Product does not operate.

•  The mains fuse is defective or has tripped. >>> Check fuses in the fuse box. if necessary, replace or reset thern.
• Product is not plugged into the socket. >>» Check the plug connection.
• Speed button might not be set. >>> Press the required speed button.
• Power is cut. >>> Check if there is power. Check the fuses in the fuse box. if necessary,replace of reset the fuses.

Hood light does not work

• Hood lamp is defective. >>» Replace the hood lamp.
• Power is cut. >>> Check if there is power. Check the fuses in the fuse box. if necessary, replace or reset the fuses.

Consult the Authorised Service Agent or the dealer where you have purchased the product if you cannot remedy the trouble although you have implemented the instructions in this section. Never attempt to repair a defective product yourself.

Arcelik AS.
Karaagag Caddesi No:2 6 Sitllice, 34445, Turkey
Made in TURKEY
Imm porter in Russia: «BE<O LLC»
Address: Selskaya street, 49, Fedovovskoe village, Pershinskoe rural settlement, Kirzhach district, Vladimir region, Russian Federation 601021
The manufacture date is included in the serial number of a product specified on rating label, which is located on a product. namely: first two figures of serial number indicate the year of manufacture, and last two _ tne month. For example, “10- 10000 1-05» indicates that the product was produced in May, 2010.
You can ask for certification number from our Call Center 8-890-200-23-56
The manufacture reserves the right for making changes in modification, design and specification of an electric device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>