DOINOW K1 Cordless Hot Wire Foam Cutter Kit User Manual
- June 2, 2024
- DOINOW
Table of Contents
DOINOW K1 Cordless Hot Wire Foam Cutter Kit
Scan the QR code for more language instructions.
Thank you for purchasing Our Kl Cordless Hot Wire Foam Cutter. Please read the Safety Instructions and User Manual thoroughly before using this product.
PRODUCT OVERVIEW
- Heating tube
- LED light
- On/Off switch
- Type-C charging port
- Charging indicator
- Heating wire
- Charging cable (Type-C)
- Bow blade
- Needle blade
- U blade
Safety
Carefully read all the safety regulations and instructions.
Failure to observe the following warnings and instructions may result in
electric shock, fire, and/or serious injury.
All safety regulations and instructions should be kept for future use.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- WARNING: This tool must be placed on its stand when not in use.
- The appliance is only to be used with the power supply unit provided with the appliance.
- This appliance contains batteries that are non-replaceable.
WARNING: For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance. The type of detachable supply unit is: M26EU050100
Safety regulations
- People who are unfamiliar with the hot cutting pen or do not understand these instructions are not allowed to operate the equipment.
- Children shall not use the hot cutting pen, Children over eight years old and persons with physical, sensory, or mental defects or lack of experience and knowledge can use this equipment if they are supervised by the person responsible for their safety or have received guidance from guardians on the use of the equipment and have learned about possible dangers. Otherwise, there is a risk of misuse and personal injury.
- Ensure children are supervised so they do not play with the equipment.
- Children are not allowed to clean and maintain the equipment without supervision.
- Check the hot cutting pen before each use, Stop use the equipment immediately if any signs of damage are found.
- Do not attempt to disassemble the hot cutting pen,disassembly may increase the risk of burns,decrease the safety of the product ,or affect the performance of the product.
- Do not leave the hot cutting pen left unattended after it is turned on. Do not touch the blade to avoid risk of burns.
- Do not worry, It is normal to produce smoke during the use of products.
- Put the product in a safe place after use to prevent it from falling from a high place.Strictly prevent children from putting the product in their mouth or playing with it.
- After use, safely store the hot cutting pen that has been turned off, and allow it to cool completely before packing it away. Avoid harm caused by the hot blade.
- This equipment is not waterproof, not resistant to falling, and it is strictly forbidden to beat it or hit other hard objects with the heating component.
- Ensure that the workplace is well ventilated. Gas and steam produced during work are likely to harm health.
- Wear safety goggles, heat resistant gloves and face mask when operate the equipment.
- In order to ensure the continuous use of this precision product,after 30 minutes of continuous,it is recommended to shut it down and stop for 60 seconds before continuing use.
Special Safety Instructions for Battery and Charger
- For the purpose of recharging the battery, only use the detachable supply unit(M26EU050100) provided with this appliance.
- If under extreme conditions any electrolyte should escape from the battery, it’s essential to avoid contact with skin. If electrolyte does come into contact with your skin, rinse it off with water. In the event of electrolyte contact with your eyes, it’s essential to consult a doctor.
- Before the use of the charger, read the instruction manual for it carefully.
- During the charge process, the current used should correspond to the current of the battery charger.
- Never let moisture, rain or splashed water reaches the charging location.
- The ambient temperature must not exceed 40oC. Never expose the device to direct insulation.
- If the electrical cable is damaged, the wire may only be replaced by the supplier or by his repair workshop. Have repairs carried out only by an authorized specialist only.
- Always keep the surface of the charger free from dust and dirt.
- Do not throw batteries into water or fire, risk of explosion!
- Never discharge the battery completely and recharge occasionally if not used for a prolonged period.
- After the equipment is fully charged, please cut off the power supply in time to prevent equipment damage or more serious disasters caused by accidents such as lightning strikes.
Technical data
- Model YC22-V4RG
- Lithium battery capacity 2000mAh
- Charging time 3-4 hours
- Maximum tempera- 550°ture C
| Input | 100-240v~,50-60HZ |
|---|---|
| Output | 5V, lA |
| Needle hot knife size | 100mm |
| Bow hot blade size | 100mm |
| U-hot blade size | 40X20X40mm |
Heating wire
diameter size
|
Operation
Installing the heating wire (Fig2)
Find the heating wire head on the heating wire reel ( 6) , wind it 4-5 times
in the cutting bow head and tighten it, and wind the other side in the same
way; The opening state of the cutting bow is slightly tightened during
winding. The opening length of the wound-cutting bow is about 80-l00mm.
Installing the hot blade (Fig 1/Fig3)
Warning! Switch off the tool before installing.
There are four type of hot blades (8/9/10) in the accessories,
Choose a suitable blade according to you need , Install it on the Heating tube(!) and ensure installed properly.
Operation the equipment (Fig 1)
Before cutting, it is recommended to draw a graph with a marker as required.
Push the switch button (3) to the ON position, the front LED Light (2) is
on,Then the working attachment begins to preheating , Wait for 10-15 seconds
to complete the preheating of the heating head and can be ready for cutting.
When replacing other heating heads, turn the switch to off position and wait
for cooling before replacing.
After it cools down, please wipe the heating needle with a damp sponge to avoid blackening and hardening caused by adhesion Of oxides
Recharge (Fig 1)
During operation, if the front LED light (2) flashes continuously, it
indicates that the battery is exhausted and you should recharge it in time.
Use a USB type-C charging cable(7} to connect the power adapter and charging
port(4} to recharge the product. If the charging indicator(5) is on in red, it
indicates that recharging is in progress; if the charging indicator (5) is on
in green, it indicates that recharging is completed.
Troubleshooting and maintenance
| Problems | Causes | Solutions |
|---|---|---|
| Blade does not heating | Heating head does not installed properly | Turn off |
switch and Reinstall the heating head
The LED light flashes| The battery is low| Recharge immediately
Unable to recharge normally| Incompatible power adapter| Use a SV power
adapter
- Attention! Please turn off the hot cutting pen before maintenance and cleaning.
- Keep the hot cutting pen clean and tidy to ensure good, safe operation.
- Do not throw the hot cutting pen, charger and battery into domestic garbage!
Warranty
The product passed rigorous and comprehensive product inspection, We are confident of the quality of our products and offer outstanding guarantees for professional users of the products.
We offer One Year Limited Warranty from date of purchasing provided that:
- Proof of purchase
- Fair wear and tear
- Have not repaired by unauthorized persons
- Has not been misused Defective products will be repaired or replaced, free of charge or at our discretion, If sent together with proof of purchase to our authorized distributors.
This Warranty does not cover:
- Faults caused by accidental damage
- Failure to use according to manufacturers’ instructions Defects caused by maintenance or renovation without our authorization
- Calibration and care are not covered by warranty
Note
- To the extent permitted by law, we shall not be liable under this Warranty for indirect or consequential loss resulting from faults in this product.
- Repair or replacement under this Warranty does not affect the expiry date of the Warranty.
- This warranty is limited to purchased customers and is not permitted to transfer this warranty.
- This Warranty may not be varied without our authorization.
You can enjoy a 12 months limited warranty but it can be up to 24 months if
you register as a member through the product registration.
Please contact us support@doinowtools.com to
activate your priority.
If you encounter any question or confusion about the product,please feel free
to contact us: support@doinowtools.com
Shenzhen AIMO Technology Co.,Ltd
E-mail: support@doinowtools.com
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>