Parrotuncle F6372110V 31 in Indoor White Flush Mount Ceiling Fan Instruction Manual

Parrotuncle F6372110V 31 in Indoor White Flush Mount Ceiling Fan

Product Specifications:

• Model: F6372BK&F6372110V
• Power Supply: 110-120V AC
• Power Consumption: 21W
• LED Power: 1*LED MAX.18W
• Quantity: 3PCS

Product Usage Instructions

Installation Precautions:
Before installation, ensure to turn off the power.

Installation Steps:

1. For Wood Ceilings :
   • Use self-tapping screws.
2. For Cement Ceilings :
   • Use expansion screws.
3. Connect the wires of the fan main unit and install it on the ceiling cover.
4. Attach the fan blade to the main unit (note the front and back of the fan blade).
5. Connect the wire for the LED light source to the LED light panel.
6. Fix the LED light panel to the connection panel.

Frequently Asked Questions (FAQ):

1. Q: What type of screws should be used for wood ceilings?
   A: Wood ceilings should use self-tapping screws for installation.

2. Q: How should the LED light panel be connected?
   A: First, fix the LED light panel to the connection panel, then connect the LED light source to the LED light panel.

F6372BK &F6372110V

Installation & Operating Instructions for the

Parrotuncle Owner’s Installation Manual

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

1. To reduce the risk of an electrical blow, electricity on the protective switch or the safety box went out before starting.
2. All wiring must correspond to the NASI/NFPA 70-1999 National Electric Code and local electrical regulations. The electrical installation must be carried out by a qualified and approved electrician.
3. The connection box and support construction must be assembled safely and 35 pounds (15.9 kilos) must be able to transport reliably. Use only output boxes listed with labeling “Accepted for fans with a weight of£ 35 (15.9 kilos) or less.”
4. The fan must be installed with a minimum distance of 2.1 m (7 feet) from the posterior edge of the wings to the floor.
5. Do not operate the reverse switch if the fan wings are moving. You have to turn off the fan and stop the wings before reverse the direction of the wing.
6. Do not place objects on the road to wings.
7. To avoid lesions or damage to the fan and other objects, be careful if you work on the fan or clean it.
8. Electrical diagrams only serve as a reference. The lighting rates that are not delivered with the fan must be listed and marked with the valve model that will be installed for use. The switches must be general use switches UL. Take into account the instructions for the appropriate installation included in the lighting rates and the switches.
9. After the electrical connections have been made, the size staircase must be turned up and carefully push to the plug box. The cables must be distributed in such a way that the ground connected driver and the device head are next to the socket. All fixing screws must be verified before installation and, if necessary, followed
   • WARNING: To reduce the risk of injury, knife supports (also known as flanges) cannot be folded during installation or after installation. Do not put any object on the path of wings.
   • WARNING: Remove rubber motor attacks at the bottom of the fan before mounting the wings or try the engine.
   • WARNING: To avoid the risk of a fire or an electrical blow, this fan should not be used with a semiconductor speed controller.
   • WARNING: To avoid a possible electric shock, tum off the current in the main security box before wiring. If you feel that you do not have enough knowled~e or experience in electrical wiring, communicate with a license electrician.
   • WARNING: Electrical diagrams only serve as a reference. The optional use of an lighting rate must be on the list and marked with this fan for use.
   • WARNING: To reduce the risk of fires, electrical discharges or injuries, assemble the device in a socket that with the inscription accepted for fans with a weight of£ 35) or less. It is marked and use the screws supplied with the plug.

TECHNICAL INFORMATION

REMOTE CONTROL(1 PCS)

Pls check whether above accessories are completed or not? Yes, and install.

Note: Turn off the power before installation
Wooden ceilings use self-tapping screws 

Connect the wires of the fan main unit and install it on the ceiling cover

Attach the fan blade to the main unit (note the front and back of the fan blade

Fix the LED light panel to the connection panel

After connecting the wire, then connect the LED light source to the LED light panel.

Effect after installation

Remote controller GENERAL INFORMATION

INSTALLING RECEIVER IN CEILING FAN

• A. Safety precautions:
  WARNING: HIGH VOLTAGE! Disconnect power by removing fuse or switching off circuit breaker. LIGHT

• Do not use with solid state fans. oUTPuT

• Electrical wire must meet all local and national electrical code requirements.

• B. Electrical rating: 110/120V 50/60Hz

• MAX. Motor watts : 40W

• MAX. Light watts : 20W

• Otherwise power can cause serious injury or death.

• Installing receiver in fan: (FlG. 2)

  • Remove power from the circuit.
  • Remove ceiling fan canopy from the mounting
  • Disconnect existing wiring between ceiling fan and ~ Supply in electrical junction box.
  • Make connections as follows, using the wire nuts (F IG.) supplied: {FlG. 1)

 OPERATING TRANSMITTER

• A. Install 2032 3 volt battery. (To prevent damage to transmitter, remove the battery if not used for a long time).
• B. Store the transmitter away from excessive heat or humidity.
• C. Operating the buttons on the panel of the transmitter.

Setting the codes on the receiver:

• The Learn Key must be pressed with in 5 seconds, after pressing the Power button.
• If not, please press the Power button to restart.
•  Keep pressing the button LEARN key in excess of 3 second it becomes a LEARN status.
• The receiver can remember the last codes status.
• The ceiling fan light flash two times. (FIG.4)

WARNING

• INGESTION HAZARD: This product contains a button cell or coin battery.
• DEATH or serious injury can occur if ingested.
• A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
• KEEP new and used batteries OUT OF REACH OF CHILDREN
• Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
• Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household t rash or incinerate.
• Even used batteries may cause severe injury or death.
• Call a local poison control center for treatment information.
• Compatible battery type is CR2032, 3 V
• Ensure the batteries are installed correctly with regard to polarity ( + and -).
• Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries
• Non-rechargeable batteries are not to be recharged. Exhausted batteries are to be removed from the product.
• Do not force discharge, recharge, disassemble, heat above (manufacturer’s specified temperature rating) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
• Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
• Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.
• WARNING INGESTION HAZARD : This product contains a button cell or coin battery

size of product

AFTER INSTALLATION WOBBLE”

• The fan blades have been adjusted in the factory to minimize any wobble
• NOTE:CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY ARE MOUNTED ON A RUBBER CROM MET. IF THE FAN WAS MOUNTED RIGIDLY TO THE CEILING, IT WOULD CAUSE EXCESS VIBRATION. MOVEMENT OF A FEW CENTIMENTERS IS QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEM
• TO REDUCE THE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURED THE MOUNTING BRACKET AND DOWNRODARE SECURE.

BALANCING A WOBBLING CEILING FAN:

1. Check that all blade and blade arm screws are secure.
2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. Measure this distance.Rotate the fan until the next blade is positioned for measurement. Repeat for each blade. The distance deviation should be equal within 1/8″(0.32cm).
3. lf the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in smoother operation.
   WARNING: TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE ARM WHILE INSTALLING, BALANCING THE BLADES, OR CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES. NOISE

When it is quiet(especially at night) you may hear occasional small noises. This is normal. Please allow hour “breaking-in” period, most noises associated with a new fan disappear during the time.

CARE AND CLEANING

1. Perlick clean Ing of your calling fan Is the only maintenance required. Use a soft brush or lint free cloth to avoid scratching the paint finish. Please make sure to turn  electricity power before you clean your fan
2. Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock.
3. Motor has permanently lubricated ball bearing. No need to oil

NOTE : MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU ATTEMPT ANY CLEANING OR REPAIRS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>