TAC TB-D11N Arrow Side Step Installation Guide

: June 2, 2024
: TAC

Table of Contents

TAC TB-D11N Arrow Side Step
Specifications
FAQ
Torque & Tools
Part List
Installation Instructions
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TAC TB-D11N Arrow Side Step

Specifications

Product: Arrow Side Step
Part Number: TB-D11N
Compatibility: Fits 2019-Up Dodge RAM 1500 Crew Cab (Exclude
2019-2024 RAM 1500 Classic Crew Cab)
Installation Time: 60-120 minutes
Cutting Not Required
Drilling Not Required

FAQ

Q: Is drilling required for installation?
A: No, drilling is not required for installing the Arrow Side Step.
Q: What tools are needed for installation?
A: Tools required include wrenches in sizes of 10mm, 13mm, 16mm, and 18mm, as well as Allen wrenches in sizes of 4mm, 5mm, 6mm, and 8mm.

Torque & Tools

Fastener Size| Tightening Torque (ft-lbs)| Wrench Required| Allen Wrench Required
---|---|---|---
6mm| 7-8.5| | 10mm| | 4mm
8mm| 18-20| 13mm| 5mm
10mm| 35-40| 16mm| 6mm
12mm| 60-70| 18mm| 8mm

BEFORE INSTALLATION

REMOVE CONTENTS FROM THE BOX.
VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
ASSISTANCE IS RECOMMENDED.

Part List

Front/Rear Lower Mounting Bracket x 4
Front/Rear Upper Mounting Bracket x 4
Center Mounting Bracket x 2
Center Support Bracket x 2

Installation Instructions

PLEASE NOTE THAT THE FOLLOWING PICTURES ARE BASED ON THE DRIVER-SIDE INSTALLATION

STEP 1

Start the installation under the Driver/Left side of the vehicle. Locate the front (3) factory studs along the inner side of the body panel, (Fig 1).

STEP 2

Select (1) Front/Rear Upper Mounting Bracket (#2). Attach the Mounting Bracket to the (3) factory studs with (3) 8mm x 24mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Fig 2). Do not tighten hardware.

STEP 3

Attach (1) Front/Rear Lower Mounting Bracket (#1) to the welded plate on the back of the Front Upper Bracket (#2) with (2) 8mm Hex Bolts, (4) 8mm x 16mm Flat Washer, and (2) 8mm Nylon Lock Nuts (Fig 3).

STEP 4

Move to the center location, (Fig 4). Select (1) Center Support Bracket (#4), attach the Support Bracket to the lower (2) factory studs with (2) 8mm x 24mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 5).

STEP 5

Select (1) Center Mounting Bracket (#3) and attach to the Support Bracket and upper threaded stud with (2) 8mm x 24mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 6). Do not tighten hardware.

STEP 6

Repeat Steps 2 & 3 to attach (1) Front/Rear Upper Mounting Bracket (#2) and (1) Front/Rear Lower Mounting Bracket (#1) to the rear mounting locations along the body panel, (Fig 7). Do not tighten hardware.

STEP 7

Select the Driver/Left Side Step. Insert (6) 6mm TBolts into the slots underneath the Side Step (Fig 8).
NOTE: The Driver/Left Side Step will have a Sticker “D” on the front.
IMPORTANT: Do not slide the Side Step front to back or damage to the finish may result.
Attach the Side Step to the (3) Mounting Brackets with (6) 6mm Flat Washers, (6) 6mm Lock Washers, and (6) 6mm Hex Nuts (Fig 9). Do not tighten hardware.

STEP 8

Level and adjust the Side Step as necessary and fully tighten all hardware.

STEP 9

Repeat Steps 1-8 to attach the Passenger/Right Side Step to the vehicle.

STEP 10

Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Attention

To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish.
Mild soap may be used also to clean the Side Steps.