EarFun UBOOM X Portable Bluetooth Speaker User Manual

EarFun UBOOM X Portable Bluetooth Speaker

EarFun Audio App

• Download the EarFun Audio app for an enhanced experience.
• No forced registration. Easy to use.
• Multi-band EQ, speaker battery status.
• Firmware update, and more.

What’s in the Box

Product Diagram

1. 1 Power Button
2. Bluetooth button
3. Volume – button
4. Volume + button
5. 5 Play/Pause Button
6. Light Effect Button
7. Party Mode Button
8. Power LED Indicator
9. Video Mode LED Indicator
10. Party Mode LED Indicator
11. Battery Level LED Indicator
12. USB-C Charging Input Port
13. USB-C Charging Output Port
14. 3.5mm Audio Input Port

Charging

1. Clean the USB-C charging port before charging.
2. Fully charge the speaker before the first use.
3. Close the port cover to avoid water damage when charging is finished.

Connect the USB-C cable to the charging input port for speaker charging.

Note:

• The speaker is built in a 7.2V/8400mAh (60.48Wh) large battery, please use an adaptor with at least 5VDC/3A output capacity or above for charging, otherwise, it will not be able to charge the speaker.
• The speaker supports the maximum 20VDC/3A fast charging input, and the fast charging time is as low as 4 hours.
• Connect the USB-C cable to the charging output port of the speaker for other Bluetooth device charging.
• The charging output port provides the maximum 5VDC/2A (10W) output.

Bluetooth Pairing

• Step 1. Power on the Speaker, then press the Bluetooth button, and the speaker will enter into pairing mode.
• Step 2: Activate Bluetooth on your Bluetooth-enabled device and search for other Bluetooth devices.
• Step 3: Select “EarFun UBOOM X” from the list of Bluetooth devices shown (if a password is needed, type ‘0000’).

Connection with Two Speakers

True Wireless Stereo Connection with Two Speakers

• Step 1. Pair and connect speaker A to your Bluetooth device.
• Step 2. Power on speaker B, and then press and hold the party mode button of both speakers (A and B) for 2 seconds at least and the party mode indicators of both speakers flash blue, then both speakers will begin to be connected to the same Bluetooth device.
• Step 3. When the indicators stay blue, the two speakers are connected successfully in True Wireless Stereo. Speaker A will be the Left channel and Speaker B will be the Right channel.
  • Note: The speakers will automatically connect in true wireless stereo mode after finishing setting up the true wireless stereo connection.

Party Mode Connection with Two or More Speakers

• Step 1. Pair and connect a master speaker to your Bluetooth device
• Step 2. Power on the other speaker, and then press the party mode button for all speakers and party mode indicators of all speakers flash white, and then all speakers will begin to be connected to the party mode.
• Step 3. When the indicators stay white, the speakers are connected successfully in party mode. All speaker will play the same sound.

Note: The speakers will automatically connect in party mode after finishing setting up the party mode connection.

Functions

changing
Party mode button| Press and hold for 2s| True Wireless Stereo mode| Blue party mode LED flash/ON
Press x1| Party mode| White party mode LED flash/ON

Notes:

• Turning on the video mode can drop latency to about 150ms and improve the video experience, but it will shorten the connection distance.
• We suggest you turn off the video mode when you use the speaker for playing music.
• Video mode does not support the True Wireless Stereo mode and party mode.
• The normal mode provides a latency of about 250ms.
• Bluetooth technology can not fully eliminate the latency of Bluetooth audio.

Reset and Reconnecting

• If this speaker becomes disconnected or has another connecting problem, you can simultaneously press and hold the “Volume +” and “Volume -” buttons for 5 seconds at least to remove all paired devices from the speaker and remove the old pairing of the speaker in your Bluetooth device, then pair again.
• If this speaker crashes, you can try to press and hold the power button for 10 seconds at least to reboot.

Specifications

• Bluetooth version V5.3
• Bluetooth frequency 2.402GHz-2.480GHz
• Bluetooth profile A2DP, AVRCP, HFP
• Maximum working range 15m(without obstacle)
• Transducer 4-inch woofer x 2, 20mm tweeter x 2
• Output power 10W
• Battery capacity 7.2V, 8400mAh
• Playtime Up to 30 hours (varies by volume level and audio content)
• Charging time <6 hours (varies by the output capacity of the adaptor)
• USB charge input 20V–3A (maximum)
• USB charge output 5V–2A (maximum)
• Dimensions 400mm x 151mm x 217mm
• Weight 4076g

FCC

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Compliance

• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
• This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

CAUTION

• Risk of explosion if the battery is replaced by an incorrect type
• Disposal of a battery into fire or a hot event, or mechanically crushing or cutting of a battery, that can result in an explosion;
• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;
• A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.

BLUETOOTH

• The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Earfun Technology (HK) Limited is under license.
• Other trademarks and trade names are those of their respective owners.

EU Declaration of Conformity

• Earfun Technology (HK) Limited hereby declares that this equipment complies with the essential requirements and other relevant provisions of Directive 2014/53/EU and RoHS 2011/65/EU Directive.
• The declaration of conformity may be consulted in the support section of our Web site, accessible from www.myearfun.com.

UK Declaration of Conformity

• Hereby, [Earfun Technology (HK) Limited] declares that the radio equipment type [SP500] complies with UK Radio Equipment Regulations (Sl 2017/1206).
• The full text of the declaration of conformity is available at the following internet address: www.myearfun.com.

ISED Compliance Statements

This device contains licence-exempt transmitter(s)/receivers) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to thefollowing two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.

• FER/MODEL: SP500
• Input: 20V==3A
• FCC ID: 2AVIT-SP500
• Output: 5V=2A

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>