sunhans SH24Go10W WIFI Signal Amplifier Installation Guide
- June 10, 2024
- sunhans
Table of Contents
sunhans SH24Go10W WIFI Signal Amplifier
Part List
Please check the part list before the installation: SH24Go 10W
- SH24Go 10W
- DC injector
- 24V DC adapter
- Quick Installation Guide
NOTE
All connected cables need to be customized, because the application scenarios
of different customers are different, so the required cable type and lengths
are also different.
If find any missing or damaged, please contact your
Hardware Installation Diagra
Step 1 Connect DC injector to AP
Step 2 Connect DC injector to SH24Go10W
Step 3 Connect DC injector to power adapter
Step 4 Power on the AP and SH24Go10W
When the SH24Go10W is Powered on, the power indicator on the DC injector will be steady Green .
Technical Specifications
Operating range : 2400 ~2500 MHz
Channel width: 20Mhz&40 Mhz Supported
standards: IEEE 802 . 11 b/g/n
Operation mode: Bi- directional, half- duplex, time division duplex
Connector type: N-K female
Output power: 1 0dBm
Input power: -30~26d Bm
Transmit gain: 22 d B
Receiver gain: ≤20d B
Noise figure: ≤ 3 . 5 d B typical
Frequency response: ± 1dB over operating range
Power adapter: 24V/2A DC, 100~240V
Operating temperature: – 25 °C to + 55 °C
Operating humidity: Up to 75% relative humidity
Material: Cast aluminum
LED light: Power status / activity status LED
Booster weight: 470g
Booster size: 15.2 x 7.3 x 2 .6cm
CAUTION :
-
Do not open the aluminum box without permission
To prevent potential damage to the environment or to human health, please separate these -
products from other kinds of waste and recycle them properly. Thus, you help foster the sustainable reusing of material resources . Home users can contact the establishment where they purchased the product or the corresponding local authorities to get information about how and where to take this waste for an ecologically safe recycling process . Major consumers can contact their provider and check the conditions of the purchase contract. Neither this product nor its electric accessories must be thrown away with other commercial waste. Must the can be used only in the system which it has obtained authorization （FCC ID：2AYN6-SH24GO10W）.
-
external antenna, covering a wide range of signals
-
RTL811CU chip,
-
20m/40m bandwidth coexistence
-
support IEEE802. 11 b/g/n
-
USB 2.0 interface
- Users need to follow the driver file of this product If it is a win1 0 system, the driver may not be required
- When the driver is installed normally, the computer will have a wireless network cardic on prompt ·
- The user can scan and connect the hotspot of the router with the wireless configuration tool of the Windows system, and then the product can be used normally
Notice
This device complies with Part 1 5 of the FCC Rules .
Operation is subject to the following two conditions: ( 1 ) this device may
not cause harmful interference, and ( 2 ) this device must accept any
interference received, including interference that may cause undesired
operation . Changes or modifications not expressly approved by the party
responsible for compliance could void the user’ s authority to operate the
equipment 。
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 1 5 of the FCC Rules .
These limits are designed to provide reasonable protection against harmful
interference in a residential installation . This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications . However, there is no guarantee that interference will not
occur in a particular installation . If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver .
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected .
— Consult the dealer or an experienced radio/ TV technician for help. Note:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>