DYNOJET PC6-20007 Power Commander 6 Installation Guide
- June 4, 2024
- Dynojet
Table of Contents
DYNOJET PC6-20007 Power Commander 6
PARTS LIST
- 1 POWER COMMANDER 6
- 1 INSTALLATION GUIDE
- 1 USB CABLE
- 2 DYNOJET DECALS
- 2 POWER COMMANDER DECALS
- 2 VELCRO STRIPS
- 1 ALCOHOL SWAB
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map
(Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You
can switch on the fly between these two base maps when you hook up a switch to
the MAP inputs. You can use any open/close type switch. The polarity of the
wires is not important.
Shifter
(Input 1 or 2) Used for clutch-less full throttle upshifts. Insert the wires
from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of
the wires is not important. Set to Input 2 by default.
Speed
If your application has a speed sensor then you can tap into the signal
side of the sensor and run a wire into this input. This will allow you to
calculate gear position in the Control Center Software. Once gear position is
setup you can alter your map based on gear position and setup gear dependent
kill times when using a quickshifter. .
Analog
This input is for a 0-5v signal such as engine temp, boost, etc. Once this
input is established you can alter your fuel curve based on this input in the
Power Core software.
Launch
You can connect a wire to either Input 1 or Input 2 and then the other end
to a switch. This switch when engaged (continuity) will only allow the RPM to
be raised to a certain limit (set in the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 first remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tighten the screw. Make sure to reinstall the rubber
plug.
NOTE : If you tin the wires with solder it will make inserting them
easier.
INSTALLING THE POWER COMMANDER 6
-
Remove the seats.
-
Prop the fuel tank up.
-
Lay the PC6 in the tail section and route the PC6 harness towards the front of the bike.
-
Route the PC6 harness along the left hand side of the bike.
-
Attach the ground wire from the PC6 to the negative side of the battery.
-
Unplug the stock wiring harness from the lower injectors.
-
Plug the PC6 wiring harness in-line of the stock harness and injectors.
Do NOT connect the PC6 harness to the upper injectors. Make sure you are on the set of injectors that are below the fuel rail.
ORANGE – #1 cylinder
YELLOW – #2 cylinder
GREEN – #3 cylinder
BLUE – #4 cylinder -
Remove the right hand side fairing.
-
Remove the 3 bolts for the regulator/rectifier bracket. This allows access to the TPS connector.
-
Locate the stock Throttle Position Sensor connector. This is a GREY 3-pin connector with PINK/BLK – RED BLK/BRN colored wires.
-
Unplug the TPS connector and plug the PC6 connectors in-line of the TPS and stock wiring harness.
-
Secure the PC6 in the tail section using the supplied Velcro. Make sure to use the alcohol swab to clean both surfaces before attaching the Velcro.
-
Reinstall the regulator/rectifier bracket and fairing. Lower fuel tank and reinstall seats.
-
Affix the supplied CARB E.O. label to a conspicuous area. The best location is next to the original emissions label. Make sure to clean the surface before attaching
Optional Inputs :
Speed input – PINK wire on BLACK 3-pin connector of speed sensor
Temperature input – BLACK/BLUE of cylinder head temp sensor
12v source for Auto-tune – BROWN wire for tail light connector
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081 –800-992-4993 – DYNOJET.COM © 2007-2020 DYNOJET RESEARCH ALL RIGHTS RESERVED
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>