Secury360 Installers Box User Guide

S360 BOX
QUICK START GUIDE
INTEGRATIONS &API

Package contents

• 1x S360 BOX
• 1x DC power supply
• 1x Screws & plug set
• 1x Quick start guide

Important before usage

When booting the device for the first time, it is essential to connect the device to the internet and to don’t reboot or unplug the device for a timeframe of 15 minutes, so that all latest updates can be downloaded.
If this procedure is not followed, software problems can occur.
After updates are downloaded, the box can be plugged/unplugged or rebooted as desired.

Mounting the device

It is possible to wall mount, rackmount or place the S360 Box on a flat stable surface.
To mount the S360 Box on a wall, please use the included M4 screws and drill a hole 50mm deep.
Use the included wall anchors to screw the S360 Box to the wall, taking care not to overtighten the screws which could damage the S360 Box housing.

Connecting the device
Plug in the internet access cable, the camera network access cable and DC power supply.
Network connection
Verify if a dynamic IP address for the internet port is obtained automatically by a local DHCP server. When there is no DHCP server available, manually set an IP address.
More information on how to do this can be found on the Partner Portal.

Using the device

When turning on the device, the power LED on the front of the device should be red.
The status LED will turn orange when the device starts booting.
When the status LED starts blinking red and the IP addresses occur on the screen, the device is booted and ready for action.
Log in to your S360 Partner portal to register the device.
The serial number needed to register the device is located on the side of the S360 Box and on the outside label of the shipping box.
Once the device is configurated in the Partner Portal and the camera’s (with the correct settings) are connected, the status LED turns green.

How do I login to my S360BOX?

Verify that your computer is connected to the same network (INTERNET& CAMERA) as the S360 BOX and that the S360 BOX is running, then follow the steps below:
STEP 1: Open your web browser and enter the serial number of the S360 BOX into the address bar (not in google). Use http:// in the url: http://SERIALNUMBER STEP2: You shouldbe taken to the S360 login page. Use the same credentials as you dowhen you login toour Partner Portal
If your login is successful, you will be redirected to the S360 BOX web interface, where you can:

• verify cameras (connections& recent detections)
• change complete network configuration (INTERNET&CAMERA)
• test outputs
• reboot the device

Check your firewall and port configuration rules

Our S360 BOX allows communication from an on-premises server to our cloud using supported protocols. The following table can be used as a guideline when configurating firewall rules for the underlying servers where our S360 BOX is hosted:

PROTOCOL| PORT|
---|---|---
MQTT| 8883 (tcp)| Outgoing
AMQP| 5671 (tcp)| Outgoing
HTTP| 80 (tcp)| Incoming/Outgoing
H-11-PS| 443 (tcp)| Incoming/Outgoing
CUSTOM| 3262 (tcp)| Incoming/Outgoing
CUSTOM| 36022 (tcp)| Incoming/Outgoing
SSH| 22 (tcp)| Incoming/Outgoing
(NOT needed by default. Only when debugging issues within local network)
NTP| 123 (tcp)| Outgoing

Activate S360BOX through an alarm panel

Attach the alarm panel’s alarm input to S360 BOX output 1 COM and NO (Alarm Output 1).
Attach the alarm panel’s output to the S360 BOX input 1 (Zone 1 Input).
You can configure different zones.

Activate S360BOX through a weekly schedule part 1
Attach one of the box outputs to the input.
If you have multiple zones, you need to link one output to one input per zone.
In the example below, output 3 is linked to input 1.
Then configure the same connection in our Partner Portal.
You can then setup your weekly schedule.

Activate S360BOX through a weekly schedule part 2
Also go to the Partner Portal and go to tab ‘S360 boxes’.
Then click on the ‘…’ under ‘Actions’ and select ‘Zones, inputs& outputs’.
Then click on ‘Next’ and add ‘SO1’ under Output 3 to configurate the connection in the Partner Portal.

I/OConfiguration
On this screen, you see a list of all available output& input actions. The alarm outputs linked to a partition are fixed and not changeable.
You can configure the remaining outputs by selecting an output action for every remaining output.
Inputs 1-3 are reserved for arming/disarming partitions, inputs 4-6 are reserved for error input (eg sabotage detection from camera)

Error output

You can connect one of our outputs to your alarm panel as a self-check. Whenever the S360 BOX is in”error” state, this output will be triggered.

By default ‘output 2’ will be used, but another output can also be configured by the installer.

More info on the output/input configuration can be found in our Partner Portal FAQ.

Warnings and notices

• Use of controls or adjustments or performance of procedures other than those specified here, may result in hazardous radiation exposure.
• Do not attempt to service or repair this product –> return it to Secury360 for service.
• Do not permit anyone other than Secury360 to service, repair or adjust this product.
• Do not attempt to open or modify this device except as described in this document.
• Do not operate this device if it is damaged or if the covers/seals are missing or damaged.
• Warranty void if the device is opened or if the covers and/or seals are missing.
• For product support, contact [email protected]

AWG)
Output| conductor size 0,2 – 2,5 mm2 (24 -12 AWG) 2A@30VDC / 0.5A@125VAC
Power| Nominal 12 V DC +/- 20%, maximum power 12W, maximum current 1A

S360 Box
Integrations &API

Integrating Secury360with other software

Secury360 now offers the possibility to integrate its revolutionary artificial intelligence with
third party software. At this moment we’ve made it possible to communicate with the
following software and video management systems.

Integration with SIA

Through SIA-DC-09 Secury360 can send an event to the receiver.

checking the boxes as shown in the figure Below

Integration with immix

Through immix, an email is sent to the control room in case of detection. This email contains details of the alarm (place, time, camera) and a link to the video fragment of detection.

If feedback of the control room is wanted:

Alarm trigger based on:

detection

Integration with Genetec

necessary to make a specific user group for Secury360)

Integration with NetworkOptix

HDD installation
Open the bottom lid of the S360 box by loosening 2 screws on the bottom of the S360 box.
Place your HDD between the brackets on the inside of the lid. Then attach the HDD to the lid using the 4 M3x8 screws.
When opening the lid, a SATA cable is visible, connect the cable to your HDD.
Close the lid of the S360 box by fastening the 2 screws on the bottom of the box.
Configuration in Secury360’s Partner Portal
Important: A local connection is required to do the first setup.
Log in to the Secury360 Partner Portal through your web browser: https://partner.secury-360.app/
Go to the tab ‘S360 boxes’ (Clients>Name>S360 boxes)
Add your S360 box by entering the Serial Number.
Go to ‘Actions’ and click on ‘Settings’
Enable Network Optix VMS by checking the box, then click ‘Save’.
The button ‘Mount HD’ appears, click on it, then click ‘Save’.
The Network Optix software is now running on your S360 box.
Go to https://nxvms.com/download/ and download the Network Optix Client software compatible with your system.
When opening the Network Optix client software, a new server will be detected named after the serial number of your S360 box. You will be asked to register a login name and a password.
Important: To start recording video, a Network Optix license key is necessary.
Visit https://www.networkoptix.com/nx-witness/request-nx-witness-pricing to obtain a license.

Bookmark detections of Secury360 in NetworkOptix

Configurating the Partner Portal

Configurating Network Optix
In Network Optix it is necessary to add a Rule in order for the detection to appear as a bookmark.

1. Right click on ‘Notifications’ and select ‘Event Rules…”
2. Clickon’+Add’
3. Make aralias shown below:

Enable digest authentication for the user:

1. Do one of the following:
   – Right-click on an existing Local User and select User Settings.
   – Right-click Users and select New User.

2. If creating a new user, select Local and enter the desired information.

3. Click on the 3 vertical dots and select Allow digest authentication for this user.

4. Click OK.

NOTE : When using authentication, it is mandatory to use lowercase credentials. We aim to support uppercase credentials in the future.

Contact information
[email protected]
+32(0)11362646
Or go to:www.secury-360.com

References

• 360官网 -360安全中心 - 360安全软件 - 360智能硬件 - 360智能家居 - 360企业服务
• Secury360
• nxvms.com/download/
• Request Nx Witness Pricing - Network Optix

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>