The Home Depot TQ10123DE-4 Ride On Excavator for Children User Manual

The Home Depot TQ10123DE-4 Ride On Excavator for Children

Product Information

Specifications

• Recommended Age: 3+
• Maximum Carrying Capacity: 25kg/55lbs
• Charging Protection Function

Product Parts

• Body Frame
• Steering Wheel
• Left Foot Pedal
• Right Foot Pedal

Installation Steps

1. Attach steering connector to the steering axle.
2. Insert wheels into the front and rear axles.
3. Connect the driving wheel to the motor slot.

Product Usage Instructions

Routine Maintenance

1. Clean the toy surface with a soft cloth.
2. Avoid prolonged sunlight exposure.
3. Regularly check and tighten loose product accessories.
4. Charge the battery when low and store properly when not in use.
5. Avoid heavy pressure and drops.

Warnings

1. Use with protective equipment.
2. Do not use in traffic areas.
3. Children should use under parental supervision.

FAQ

1. Q: What is the recommended age for this product?
   A: The recommended age is 3 and above.

2. Q: How should I maintain the product?
   A: Clean with a soft cloth, avoid sunlight exposure, tighten loose accessories, charge battery when low, and store properly.

Before You Start
Please read all instructions carefully and keep it for future reference.

Warnings
Attention! Use it with protective equipment.

• Not use it in the traffic.
• Children should use this product under the parental supervision.

General Warnings

• The product must be installed and used under the supervision of an adult.
• Read through each step carefully and follow the proper order.
• Remove all packaging, separate and count all parts and hardware.
• Please ensure that all parts are correctly installed, incorrect installation can lead to a danger.
• We recommend that, where possible, all items are assembled near the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.
• Ensure a secure surface during installation, and place the product always on a flat, steady and stable surface.
• Please use this product with caution.
• The use of this product requires superb skills to avoid accidents to the user or others due to a fall or collision.
• Please wear suitable protective equipment during use, e.g. protective helmet, gloves, knee pads, elbow pads etc.

Warning

• Prevent fire or electric shock
  1. Use only the charger and battery specified by the manufacturer, do not use other brands of chargers and batteries, otherwise they may cause fire and explosion.
  2. Do not use this charger and battery on other products, otherwise it will overheat and may cause fire and explosion.
  3. Do not change the wiring structure of the product without permission, otherwise it may cause fire and explosion, and may lead to permanent damage to the product.
  4. Do not use tools to connect the positive and negative terminals of the battery, otherwise it may cause fire and explosion.
  5. Always keep the battery dry, do not let it contact fresh or salt water.
  6. The battery will produce harmful gas and irritating smell when charging. Smoking is strictly prohibited near the charging battery, and any flame or spark is strictly prohibited to avoid accidents such as explosions.
  7. Must be in a well-ventilated, dry area to charge the vehicle.
• Do not open the battery and charger.
• Do not turn the battery upside down.
• The transformer or battery charger wires, plugs, shells and other components should be checked periodically for damage, and if damaged should be discontinued until repaired.
• It is normal for the battery to heat up during the charging process, but when the temperature is too high, you should promptly check whether the charging current is too large or whether the battery is short-circuited inside.
• Must use the plate to fix the battery. If the car is overturned, the battery may fall out and hurt children.
• If the product is collected or not used for a long time, it must be fully charged first, and charged once a month to ensure the lifespan of the battery.
• Charger and battery is not a toy, do not allow children to touch and play.

Routine Maintenance

1. Use a soft cloth to clean the dirt on the surface of the toy;
2. The product should avoid prolonged sunlight exposure;
3. Regularly check whether the product accessories are loose, if loose, please use a screwdriver to fix it tightly;
4. When the battery is low, please charge it in time. If it is not used for a long time, please take out the battery and store it;
5. Avoid heavy pressure and heavy drop of the product.

Warning

1. This product is suitable for children 3+;
2. This product may have potential sharp edges, tips or small parts before assembly and must be assembled by adults;
3. This product is strictly prohibited in nearby motor vehicles, streets, steps, slopes, hills, roads, alleys, swimming pools or other places with water;
4. This product shall be used under the custody of adults and shall wear shoes;
5. This product is only limited to one-person ride, with a maximum carrying capacity of 25kg/55lbs.

Warning

• This product has a charging protection function: when charging, all functions of the vehicle are not available!
• Charging must be done by adults! The charger and battery must not be touched by children!

Product Parameters

• Product Name: Kids Ride On Excavator
• Product No.: TQ10123
• Suitable Age: 3+
• Maximum Weight: 25kg/55lbs
• Material: PP, ABS
• Product Size: 110×37×64cm/43.5″×15.5″×25″

Parts List

Accessories List

Installation Steps

Front wheel installation

1. ①Connect the Φ1020mm washer to the steering axle, and then insert it into the body frame. ②Insert the steering connector (mark facing downward) into the steering axle, and fix it with 416mm round head screw and 4*12mm washer.
2. Insert the Φ10*16mm washer into the front axle as shown, and then into the hole of the steering part.
3. Insert wheels and Φ 10*20mm washers into the front axle as shown.
4. Insert the pin into the front axle to fix the wheel as shown.

Rear wheel installation

1. Put the Φ10*20mm washer, wheel and wheel sleeve on the rear axle in turn, and then insert them into the rear of the car body as shown.
2. Insert the driving wheel into the rear axle, and snap it into the motor slot.
3. Insert the Φ10*20mm washer, and fix the wheel with the pin.
4. Install 4 decorative rings as shown.

Foot pedal installation

1. Pass the wire of right foot pedal through the body, and connect it to the power connector.
2. Snap the right foot pedal into the car body.
3. Turn the body over, ①Fix the bottom of the body and the pedal with 4*12mm flat head screws. ② Fix the side and the pedal, and install the left foot pedal according to steps 2 and 3.

Steering wheel installation

1. Press the end of the steering axle with your hand, and then insert the steering wheel as shown.
2. Lock the steering wheel with # 2 screw.

Anti-rollover piece installation

Insert the anti-rollover piece into the rear slot, and tighten it with 4*12mm round head screw.

Backrest installation

Insert the backrest into the slot as shown.

Digging arm installation

1. Insert the left & right arm linkages into the opposite hole of the arm body, and fix it with # 4 screw.
2. Align the slots of the bucket and left & right arm linkages, and then tighten.
3. Snap the arm manipulator 2 into the arm body slot as shown.
4. Snap the arm manipulator 1 into the arm body slot as shown, and fix it with # 5 screw.
5. Fix the arm linkage 3 to both ends of the arm and bucket with screws # 3 and # 1 as shown, and the arm assembly is completed.
6. Remove the bolt on the body, then insert the assembled digging arm into it as shown, and then fix it with the bolt, the whole installation is completed.

Function Introduction

Display introduction

• A. USB interface
• B. Microphone
• C. Early education function / V-
• D. Story function / Start button
• E. Music function / V+
• F. Mode switch button (Bluetooth/Music)
• G. Battery display
• H. Forward/Neutral/Reverse button

Note: D button function: start/stop; control music; automatic power off without operation for three minutes.

Steering wheel button

Press this button to make a  “beep” sound.

Accelerator pedal

When the H button is at “▲”, press the accelerator to drive the wheels forward; when the H button is at “▼”, press the accelerator, it will reverse; when the H button is at “○”, it is neutral.

Adjustable backrest

The backrest can be adjusted to first or second gears with the button.

1. When the backrest is pressed down and the button is in the first gear position, the drive function works normally.
2. When the backrest is lifted upward, the button is in the second gear position, the drive function is disabled, the seat can be rotated left and right 15-degree to dig.

Charging Method

1. Insert the plug of the charger into the charging hole, located at the end of the body as shown.
2. Plug the charger into the power outlet.

• When charging, the power switch must be turned off.
• It is recommended to charge for 4-6 hours before the first use, but do not exceed 10 hours.
• When the driving speed of the vehicle becomes significantly slower, it means that the battery power is insufficient, please charge it in time.
• Please charge for 8-12 hours after each good use, but do not exceed 20 hours.

Battery-Safety Warning

• Non-rechargeable batteries cannot be charged.
• Rechargeable batteries should only be charged under adult supervision.
• Rechargeable batteries should be removed from the toy before charging.
• Different types of batteries or old and new batteries should not be mixed.
• Batteries should be placed in the correct polarity.
• Exhausted batteries should be removed from the toy.
• Power terminals should not be short-circuited.
• Dry batteries are not provided for this product.

The following batteries or accumulators are contained in this electronic device

Information on the safe removal of the batteries or accumulators

• Warning: Make sure the battery is completely drained.
• Open the seat, unscrew the 4 screws, take out the cover and unplug the battery wires to remove the battery.
• Carefully remove the battery or accumulator.
• The battery or accumulator and the device can now be disposed of separately.

Return / Damage Claim Instructions

• DO NOT discard the box / original packaging.
  In case a return is required, the item must be returned in original box. Without this your return will not be accepted.

• Take a photo of the box markings.
  A photo of the markings (text) on the side of the box is required in case a part is needed for replacement. This helps our staff identify your product number to ensure you receive the correct parts.

• Take a photo of the damaged part (if applicable).
  A photo of the damage is always required to file a claim and get your replacement or refund processed quickly. Please make sure you have the box even if it is damaged.

• Send us an email with the images requested.
  Email us directly from marketplace where your item was purchased with the attached images and a description of your claim.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>