Designed Frama Studio Ovoid Sconce Instruction Manual

Designed Frama Studio Ovoid Sconce

Product Information

Specifications

• Input voltage: 220V-240V ~ 50Hz/60Hz
• Bulb type: G9, max 5W LED
• Item numbers: FR-2911

Product Usage Instructions

Pre-Installation Steps
Before starting the installation process, ensure to shut off power to the circuit. Seek advice from an authorized electrical contractor if needed.

Installation Steps

1. Unscrew the 2 set screws and remove the bracket from the frame using the allen key provided.
2. Feed the electrical wires through the rubber grommet and mark where to drill the holes in the wall.
3. Drill holes in the wall and fix the bracket using anchors and screws suitable for the wall type.
4. Locate and connect the live (brown), neutral (blue), and ground (green/yellow) wires from the wall output to their respective terminals on the fixture.
5. Push the wires and terminal connectors inside the metal frame and secure it over the bracket against the wall by gently tightening the set screws.
6. Insert a G9 LED bulb into the socket and carefully screw on the glass shade without overtightening it.

Final Steps
Once all parts are correctly installed, cautiously turn on the electrical power.

FAQ

• Q: Can I use a bulb with a wattage higher than 5W?
  A: No, it is recommended to use a G9 bulb with a maximum wattage of 5W to prevent damage to the fixture.

• Q: What should I do if the set screws do not protrude evenly?
  A: Ensure that the bracket is securely fixed to the wall before pushing the frame against it. Adjust as needed to achieve even protrusion of set screws.

Safety Instruction

The safety of this appliance can only be guaranteed if these instructions are observed during both installation and use. Please retain these safety instructions.

REMARKS

• When installing and whenever acting on the appliance, ensure that the power supply has been switched off!
• The appliance may in no way be modified or tampered with: any modification may compromise safety causing the appliance to become dangerous. FRAMA declines all responsibility for products that have been modified.
• Should the external trailing cable get damaged, it must be replaced by FRAMA or by qualified personnel to avoid any danger.
• The symbol shown on the device indicates that the product must be disposed of differently from standard urban waste.
• Use the appliance only with the power supply provided and at the rated voltage specified on the appliance.
• This appliance is for indoor use only.
• The appliance may not be used in humid or external environments.
• Never cover the appliance while it is turned on.

CLEANING INSTRUCTIONS

• To clean the appliance, please only use a soft cloth.
• Warning: do not use alcohol or other solvents.

Package Contents

In this box you will find:

• 1 Ovoid sconce frame with terminal connectors
• 1 mounting bracket with set screws
• 1 glass Ovoid shade

Supplementary tools:

• drill
• allen key
• 2 anchors and screws (depending on wall material)

IMPORTANT
Always shut off power to the circuit before starting installation work. In some countries, electrical installation work may only be carried out by an authorised electrical contractor.

Contact your local electricity authority for advice.

Installation Instructions

Please read the installation instructions in full before moving on to the installation itself!

1. Start by unscrewing the 2 set screws and remove the bracket from the frame.
2. Feed the electrical wires from the wall output through the rubber grommet and mark where to drill the holes.
3. Drill holes in the wall and fix the bracket to the wall using anchors and screws that are suitable for the wall type.
4. The final result should look like below.
5. Locate the live, neutral, and earth wires from the wall output, and insert them into their respective terminal (brown to brown, blue to blue and green/yellow to green/yellow).
6. Gently push the wires and terminal connectors inside the metal frame, and push the frame over the bracket against the wall.
7. Gently tighten the set screws. Both screws should protrude evenly. Do not overtighten the screws!
8. Place a suitable G9 LED bulb into the socket and gently screw on the glass shade. Screw on the glass shade with great care and do not overtighten it!

When all parts are installed correctly and properly, the electrical power can be turned back on.

TECHNICAL DATA

• Input voltage: 220V-240V ~ 50Hz/60Hz
• Bulb type: G9, max 5W LED
• Item numbers: FR-2911
• 2-year warranty.

Frama Head Office & Studio
Frama, Org. St. Pauls Apotek Fredericiagade 57 1310 Copenhagen Denmark.

Frama Amsterdam Lighting Studio
Amsterdam Studio Meeuwenlaan 126B 1021 JN Amsterdam Netherlands.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>