Hotpoint AH12H15D3B PTAC Heat Pump Unit with Electric Heat Backup 20 Amps Instruction Manual
- May 15, 2024
- Hotpoint
Table of Contents
Hotpoint AH12H15D3B PTAC Heat Pump Unit with Electric Heat Backup 20 Amps
Specifications
- Model : AH12H15D3B
- Heater Watts : 3,500 / 2,897
- Heater BTU : 10,900 / 8,900
- Heater Amps : 15.3 / 13.7
- Min Circuit : 20 amps
- Recommended Protective Device: 20 amp time-delay fuse or breaker
- Heat Pump Watts : 1180 / 1120
- Heat Pump BTU : 13,400 / 13,100
- COP : 3.2
Product Usage Instructions
Wall Case Dimensions:
Make sure to measure and adhere to the following wall case dimensions for proper installation:
- A : 30 inches
- C : 70 inches
Wall Opening Dimensions:
Add 1/4 inch to both A and C dimensions for all cut-outs. The wall opening dimensions should be at least 16-1/4 inches in height and 42-1/4 inches in width.
Electrical Connection:
Ensure that the unit is connected to a 230/208-volt line with the appropriate amperage. Follow electrical codes and guidelines for safe installation.
Heater and Heat Pump Operation:
Refer to the provided specifications for the heater watts, BTU, and amps, as well as the heat pump watts, BTU, and COP values. Adjust settings as needed for desired heating or cooling.
FAQ
- Q: What is the recommended protective device for the AH12H15D3B unit?
- A : The recommended protective device is a 20 amp time-delay fuse or breaker to ensure safe operation.
DIMENSIONS AND INSTALLATION
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
ELECTRICAL WIRING
- All wiring, including installation of receptacle, must be made in accordance with local electrical codes and regulations.
- NOTE : Aluminum wiring may pose special problems – consult a qualified electrician.
GRILLE OPTIONS
- Stamped Aluminum Grille – RAG70
ELECTRICAL CONNECTION
- 230/208-volt units must be plugged into a receptacle. Installation must comply with local electrical codes and regulations.
- The power cord is permanently attached on all Hotpoint chassis.
AH12 ELECTRIC HEATER
WALL CASE DIMENSIONS
- RAB80 WALL SLEEVE
- Heavy-gauge galvanized steel, with insulation, for quick self-assembly.
- A – 42”, B – 13-3/4”, C – 16”
MAXIMUM CORD EXTENSION
- WALL OPENING DIMENSIONS
- Add 1/4” to A and C dimensions for all cut-outs.
- RAB80 16-1/4” Min. H x 42-1/4” Min. W
FEATURE AND BENEFITS
- 14,800 / 14,600 cooling BTU
- 10.6 EER
- 13,400 / 13.100 heating BTU
- 3.2 COP
- R32 Refrigerant – Environmental friendly, low GWP (Global
Warming Potential)
- 3-Speed Fan – Give guests control over their comfort with three fan speeds to choose from
- 4-Temperature Limiting Options – Easily select one of four temperature ranges for peak efficiency and total customer comfort
- Intuitive Display – Allow guests to easily customize their preferred settings and reduce maintenance calls with an easy-to-use control panel
- Power Cord (LCDI) Included – Hotpoint PTACs come with everything needed for a quick and easy installation
- Automatic Emergency Heat – Keep guests comfortable with a heating option that uses electric resistance heat in heat pump mode
- Freeze and Frost Protection – Automatic freeze and indoor frost control keep units operating in peak condition
- Auto Power Recovery – In case of power failures, units automatically resume their operation when power is restored, reducing maintenance calls
- Self Diagnostics – Quickly and easily identify service needs with a nine-point diagnostic code system
- Backed by an Industry Leader – With a long history of creating durable products at an affordable price, Hotpoint is your trusted PTAC brand
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>