SEALEY MS0630 Motorcycle Dolly Rear Wheel Side Stand Type User Manual

SEALEY MS0630 Motorcycle Dolly Rear Wheel Side Stand Type

Specifications

Model No: MS0630

Capacity: Max. Dolly Load: 300kg / Max.

Motorcycle Weight : 500kg

Loading Track Dimensions (L x W x H): 550 x 250 x 120mm

Overall Dimensions (L x W x H): 1300 x 650 x 120mm

Product Usage Instructions

Safety Precautions

• Maintain the dolly in good condition by using an authorized service agent.
• Replace or repair damaged parts with genuine parts only.
• Locate the dolly in a suitable work area with adequate lighting.
• Ensure the floor is level and strong enough to support the dolly and motorcycle.
• Avoid using the dolly on unstable surfaces like tarmacadam.
• Keep the dolly clean for optimal performance.
• Do not exceed the maximum motorcycle weight limit of 500kg.
• Secure the motorcycle to the dolly with appropriate straps.
• Pull the motorcycle rather than push to reduce the risk of tipping over.
• Maintain correct balance and footing, avoid overreaching.
• Avoid using the dolly for tasks it is not designed for.
• Do not use a damaged dolly, when tired, under the influence, or by untrained persons.
• Avoid modifications to the dolly.
• Clean all parts before storing in a safe area.

Introduction

The motorcycle dolly is designed to hold a single motorcycle with a side stand, weighing up to 500kg. It allows easy maneuvering in workshops or garages. The front wheel remains on the ground for steering, and the pivoting feature accommodates various side stand designs.

Assembly

Refer to the attached parts list for assembly instructions.

FAQ

• Q: What is the maximum weight capacity for the Sealey Motorcycle Dolly?
  • A : The maximum weight capacity is 500kg for the motorcycle.
• Q: Can I use the dolly on tarmacadam surfaces?
  • A : It is not recommended to use the dolly on tarmacadam surfaces as they may be unstable.
• Q: How should I secure my motorcycle to the dolly?
  • A : Use appropriate straps to secure the motorcycle to the dolly before maneuvering.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.

IMPORTANT : PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE

Refer to Instruction Manual

SAFETY

• Maintain the dolly in good condition (use an authorized service agent).
• Replace or repair damaged parts. Use genuine parts only. Unauthorized parts may be dangerous and will invalidate the warranty.
• Locate the dolly in a suitable work area. Keep the area clean and tidy and free from unrelated materials, and ensure that there is adequate lighting.
• Ensure that the floor is level and strong enough (preferably concrete) to take the weight of the dolly and the motorcycle.
• DO NOT use the dolly on tarmacadam, as the surface may be unstable.
• Keep the dolly clean for the best and safest performance.
• The maximum motorcycle weight is 500kg. DO NOT exceed this rated capacity.
• Use appropriate straps to secure the motorcycle to the dolly when maneuvering.
• Pull rather than push the motorcycle when maneuvering on the dolly to reduce the risk of pushing the motorcycle off its side stand.
• Maintain correct balance and footing, DO NOT overreach. Ensure the floor is not slippery and wear non-slip shoes. Keep children and unauthorized persons away from the work area.
• DO NOT use the dolly for a task it is not designed to perform.
• DO NOT use the dolly if it is damaged.
• DO NOT use the dolly when you are tired or under the influence of alcohol, drugs or intoxicating medication.
• DO NOT allow untrained persons to use the dolly.
• DO NOT make any modifications to the dolly.
• Before storing in a safe area, ensure that all parts are clean and free of grease and oil.
• WARNING!: The warnings, cautions, and instructions in this manual cannot cover all possible conditions and situations that may occur.
• It must be understood that common sense and caution are factors that cannot be built into this product but must be applied by the operator.

INTRODUCTION

The motorcycle dolly holds a single motorcycle with a side stand, weighing up to 500kg with weight being dispersed between front and back wheels. Easy to maneuver around the workshop or garage. The front wheel stays in contact with the ground allowing the motorcycle to be steered into the desired position. The pivoting feature allows flexibility in side stand designs. The side stand holder can be adjusted to cater to the majority of motorbikes.

SPECIFICATION

Model/ No MS0630

• Capacity: Max. Dolly Load: 300kg/ Max. Motorcycle
• Weight : 500kg.
• Loading Track Dimensions (L x W x H): 550 x 250 x 120mm
• Overall Dimensions (L x W x H): 1300 x 650 x 120mm

ASSEMBLY

Also, refer to the attached parts list.

Description

1. Platform For Arm
2. Hx Hd Set Screw M10 x 15mm Zinc
3. Arm
4. Socket Cap Bolt M10 X 35mm
5. Steel Nut M10 Zinc
6. Swivel Castor
7. Platform
8. Swivel Castor (c/w Brake)
9. Flat Washer M10 Zinc
10. Nyloc Nut M10 Zinc

Remove with care all contents from the outer packaging, and check parts against the attached parts list.

• Place Platform For Arm (1) on the ground and attach 2 x Swivel Castors with c/w Brake (8), Socket Cap bolt (4), Flat Washers (9), and Nyloc Nut (10). See Fig. 1. for illustration.
•  Attach Swivel Castors (6) using Flat Washers (9), and Socket Cap bolts (4). Fasten using Nyloc Nut (10).
• Take Platform (1) and attach wheel (6b) using Flat Washers (9), and Socket Cap bolt (4). Fasten Nyloc nut (10) to Arm (3).
• Place Platform (7) on the ground, and line up Arm (3) with Platform (7). Insert the two Hx Hd Set Screw (2) into the two holes on Arm (3).

Tighten using Steel Nuts (5). The support arm can move in relationship to main part and can be adjusted to the position/design of side stand before bolt is tightened fully.

OPERATION

WARNING! Ensure that you read, understand and apply the safety instructions before use.
WARNING! DO NOT overload the dolly.

LOADING

• Position the dolly in a suitable area, checking that the surface on which the dolly will be used is solid and flat.
• Apply the brakes to the two swivel castors (8).
• Push the motorcycle onto the dolly, positioning the rear wheel centrally on the main part and support with the side stand on the support arm. Adjust as required and fix in position by tightening set screw (2). The front wheel remains on the ground.
• Secure the motorcycle using suitable straps.
• Release the braked castors (8) to allow the dolly to be maneuvered.

UNLOADING

• Apply the brakes to the two castors (8).
• Holding the handlebars lift the side stand and remove the motorcycle from the dolly.
• Store the dolly in a safe, dry, childproof location with the brakes on.

MAINTENANCE

• Before use, check the frame assembly and platform for cracks and damage.
• Regularly check that all fasteners are tight.
• Periodically lubricate the castors.

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts
without prior notice.

• IMPORTANT: No Liability is accepted for incorrect use of this product.
• WARRANTY: Guarantee is 12 months from purchase date, proof of which is required for any claim

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

• 01284 757500
• sales@sealey.co.uk
• www.sealey.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>