WAVEFORM WF-UAM UltraPole Universal Antenna Mount Installation Guide

WAVEFORM WF-UAM UltraPole Universal Antenna Mount

Base Kit

• A 1x J-Pole
• B 1x Footpad
• C 4x Bolts, Plastic Washers, and Flange Nuts*
• D 5x Expansion Bolts*
• E 5x Wood Screws and Anchors*
• F 1x Size-8/10mm Wrench
• G 4x Zip and Velcro Ties
  

Extension Kit

• A1x Extension Pole
• B2x Brace Arms
• C2x Bolts, Plastic Washers, and Flange Nut
• D 5x Expansion Bolts*
• E5x Wood Screws and Anchors*
• E 1x Size-8/10mm Wrench
• G1x Size-4mm Allen Wrench
  

Where to Install the Universal Antenna Mount

Here are some suggestions on where to install the Universal Antenna Mount:

1. Rooftop. When installing on a roof, make sure to properly seal any penetrations made by screws. Consider using pitch pads, roofing sealant/caulking/cement, or other weather proofing materials.
2. Wall / Siding / Fascia. Installing on the side of a building? Make sure the footpad(s) are secured against a sturdy material. Damaged, rotted, or weakened material may cause issues later on.
3. Pole / Railing. If your roof or siding isn’t suitable, the Universal Antenna Mount can be installed against a pole or railing. In such cases, hose-clamps or U-bolts are recommended.
4. And many more! Don’t let an instruction manual be the boss of you. You’re Leonardo da Vinci, and installing this mount is your Mona Lisa. It includes mounting equipment to enable its installation at a variety of locations! It’s called the Universal Antenna Mount for a reason.

Screw & Bolt Guide

To assemble the mount , use the Bolts, Plastic Washers, and Flange Nuts.
To install the mount against a surface , use the Wood Screws, Anchors, and Expansion Bolts.

• For hard materials (e.g. concrete, brick mortar):
  • Use the Wood Screws & Anchors.
  • The Anchors require a pre-drilled 10mm hole.
• For semi-soft materials (e.g. wood):
  • Use the Wood Screws.
• For soft materials, (e.g. plaster, drywall):
  • Use the Expansion Bolts.
  • The Expansion Bolts require a pre-drilled 12mm hole and PH2 Phillips-head screwdriver (not included).

Tip : Prior to drilling, place the footpad against the intended mounting surface and mark the location of each hole with a pencil or marker.

Assembling the Base Kit

Use the provided Size-8/10mm Wrench to assemble the Base kit. Follow the steps listed below:

1.  Install Footpad against a surface.
   

2. Install Footpad against a surface.
   

3. Install adjustment Bolt and adjust J-Pole
   

4.  (Optional) Install lock Bolt.
   

5.  Secure each Bolt with a Washer and Nut
   

Assembling the Extension Kit

Use the provided Size-8/10mm Wrench and Size-4mm Allen Wrench to assemble the Extension Kit. Follow
the steps listed below:

1. Insert Extension Pole into J-Pole. Install lock Bolt.
   

2. Secure Bolt with a Washer and Nut. Attach Brace Arms.
   

3. Adjust Brace Arms into position.
   

4. Install Footpads against a surface.
   

5. Tighten each Brace Arm Bolt into place.
   

Attaching an Antenna to the Universal Antenna Mount

These details depend on the antenna you’ve purchased. The steps below describe how to attach the L-Bracket and U-Bolt assembly included with many of our Waveform antennas.

1. Attach L-Bracket to the Antenna
   

2. Position Clamps and U-Bolts onto the Pole.
   

3.  Install L-Bracket onto Clamps and U-Bolts.
   

4. Secure assembly with Washers and Nuts.
   

Grounding the Universal Antenna Mount

Grounding an antenna mast is highly recommended. It’s required by the National Electric Code (NEC) and the mast’s metal frame makes it a prime target for lightning strikes. Follow the steps listed below:

1. Attach a Ground Wire to an In-line Surge Protector (as shown) or to the Antenna’s Grounding Port.
   

2. Attach the Ground Wire(s) to the Footpad’s Grounding Bolt. Secure the assembly with a Nut.
   

3. Attach the Ground Wire to an suitable Electrical Ground.
   

Grounding Tips

• The NEC recommends a 10 AWG or lower gauge (thicker) for grounding cables.
• In-Line Surge Protectors can protect your equipment & prevents lightning from entering your home through the cable.
• If you’re unsure about your grounding setup, reach out to an electrical contractor.
• Learn which Electrical Grounds are suitable and more at waveform.com/grounding

Customer Support

Run into any issues or have any suggestions? Call 1-800-761-3041, or email help@waveform.com to get connected with our dedicated Waveform Signal Specialists. We’d love to hear from you.
The Universal Antenna Mount is designed, sold, and supported by Waveform and our team of Signal Specialists. If you have any feedback on how we could make this mount or manual better, we’d love to hear from you.
We love hearing our customer’s experience with our products, so please reach out!

References

• Waveform - The Cell Signal Specialists
• How to Ground a Rooftop Signal Booster or DAS Antenna

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>