SEALEY SA400 Digital Tyre Inflator With Clip On Connector Instruction Manual

SEALEY SA400 Digital Tyre Inflator With Clip On Connector

Product Information

Specifications

• Product: Digital Tyre Inflator with Clip-On Connector
• Model No: SA400
• Manufacturer: Sealey
• Issue: 2 (3)
• Date: 28/07/23
• Warranty: 12 months from purchase date

Safety Instructions

• Disconnect the gauge from the air supply before servicing or performing any maintenance.
• Maintain the gauge in good condition and keep it clean for best performance.
• Replace or repair damaged parts with recommended parts only.
• Locate the gauge in a suitable work area with adequate lighting.
• Avoid directing the gauge outlet at yourself or others.
• Do not carry the gauge by the hose or yank it from the air supply.
• Operate the gauge only for its intended purpose.
• Avoid operating the gauge when tired or under the influence.
• Do not use the gauge if parts are missing or damaged.

Operation

1. Read and follow all safety instructions.
2. Refer to the instruction manual for detailed guidance.
3. Wear eye protection during operation.
4. Ensure the gauge is connected securely to the tyre valve.
5. Turn on the inflator and set the desired pressure level.
6. Monitor the pressure display and stop when the desired pressure is reached.
7. Turn off the inflator and disconnect it from the tyre valve.

Maintenance

• Dispose of the product in compliance with WEEE regulations.
• Recycle unwanted materials and dispose of fluids properly.
• Register your purchase for warranty claims.

Environment Protection
Recycle unwanted materials instead of disposing of them as waste. Drain any fluids into approved containers and dispose of the product and fluids according to local regulations.

Note on Warranty
No liability is accepted for incorrect use of this product. Proof of purchase is required for any warranty claim.

Frequently Asked Questions (FAQ)

• Q: How do I set the desired pressure level on the digital tyre inflator?
  A: To set the desired pressure level, use the control buttons on the inflator to increase or decrease the pressure reading on the display until it reaches the desired level.

• Q: Can I use this inflator for other tasks besides inflating tyres?
  A: No, it is recommended to use the inflator only for its intended purpose of inflating tyres to avoid damage or injury.

• Q: How often should I maintain the digital tyre inflator?
  A: Regular maintenance is essential for optimal performance. It is recommended to follow the maintenance instructions provided in the user manual and seek professional servicing when needed.

DIGITAL TYRE INFLATOR WITH CLIP-ON CONNECTOR

• MODEL NO: SA400
  Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

• IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

• Disconnect the gauge from the air supply before servicing or performing any maintenance.
• Maintain the gauge in good condition (use an authorised service agent), and keep the gauge clean for best and safest performance.
• Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
• Locate gauge in a suitable work area, keep area clean and tidy and free from unrelated materials and ensure there is adequate lighting.
• Keep children and unauthorised persons away from the work area.
• DO NOT direct gauge outlet at yourself or at other persons or animals.
• DO NOT carry by the hose, or yank the hose from the air supply.
• DO NOT use the gauge for a task which it is not designed to perform.
• DO NOT operate the gauge when you are tired or under the influence of alcohol, drugs or intoxicating medication.
• DO NOT operate gauge if parts are missing or the gauge is damaged, as this may cause failure and/or personal injury.

INTRODUCTION

Die-cast body and digital type gauge with rubber protector. Displayed in psi, bar, kpa and kg/cm². Fitted with 500mm rubber hose and single clip-on connector. Supplied with 2 x AAA batteries.

SPECIFICATION

• Model no …………………………………………………………… SA400
• Max. air supply …………………………………………………… 150psi
• Pressure units ……………………………. psi, bar, kpa and kg/cm²
• Range ………………………………………………. 0-10bar(0-150psi)
• Inlet size …………………………………………………………..1/4”BSP
• Battery ………………………………………………2 x AAA (supplied)

OPERATION

1. The air supply must be clean and dry, use a suitable filter/water trap.
2. The supply pressure must be to specification (see above).
3. Max. available pressure can not exceed the supply pressure.
4. TURN ON
5. Press On/Off button.
6. Press again to scroll through units.
7. Press light On/Off button to turn light off (if not required).
8. ATTACH ADAPTOR TO VALVE
9. Push down clip and place the connector onto the tyre valve.
10. The connector will now be locked in place.
11. TO INFLATE
12. Momentarily depress the operation lever fully, then release to
13. display tyre pressure.
14. Fully depress lever for an appropriate period. Avoid over inflation, release lever frequently to check the pressure.
15. TO DEFLATE
16. Depress deflate button (until air can be heard escaping) for an appropriate period. Fully depress lever momentarily then release to display new pressure.
    IMPORTANT – ALWAYS FULLY DEPRESS LEVER MOMENTARILY BEFORE READING TYRE PRESSURE.

MAINTENANCE

1. PERIODIC CHECKS AND MAINTENANCE
   For long service and accuracy, the following actions should be carried out at the recommended intervals:

2. WEEKLY – CHECK OPERATION
   The gauge should be checked weekly for correct operation. Look for smooth lever operation and fast, smooth gauge movements. Check for leaks from tyre connector seals, and for chafing or wear of the flexible hoses. Any problems should be immediately rectified.

3. QUARTERLY – CHECK CALIBRATION
   We recommend the accuracy of the gauge be checked against a calibrated ‘master’ gauge every 3 months, or at shorter intervals depending on operator’s own quality procedures.

4. BATTERY CHANGE
   When display will not illuminate renew battery. Undo clip door, remove batteries and replace, observing polarity.

WEEE REGULATIONS

• Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

• BATTERY REMOVAL
  Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.

• ENVIRONMENT PROTECTION
  Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

• Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

• Important: No Liability is accepted for incorrect use of this product.

Warranty

Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 sales@sealey.co.uk www.sealey.co.uk
© Jack Sealey Limited

Documents / Resources

| SEALEY SA400 Digital Tyre Inflator With Clip On Connector [pdf] Instruction Manual
SA400, SA400 Digital Tyre Inflator With Clip On Connector, Digital Tyre Inflator With Clip On Connector, Tyre Inflator With Clip On Connector, Inflator With Clip On Connector, Clip On Connector, Connector
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>