SEALEY MK65.V3 Masking Paper Dispenser Instruction Manual

SEALEY MK65.V3 Masking Paper Dispenser

Product Information

Specifications

• Model: MK65.V3
• Roll Size: Up to 450mm
• Usage: Floor standing or wall mounted
• Features: Automatically applies adhesive tape to edges of masking paper

Product Usage Instructions

Safety

• Ensure the dispenser is on a flat, level floor or securely wall-mounted.
• Check that all fittings are tight and secure.
• Handle the paper cutting blades with care as they are sharp.
• Use the dispenser only for its intended purpose.
• Avoid sitting or standing on the dispenser.

Introduction
The single roll dispenser accepts rolls up to 450mm and can be used either floor standing or wall mounted. It automatically applies adhesive tape to the edges of masking paper.

Contents
Refer to the provided figure for a detailed list of components included in the packaging.

Assembly

1. If the dispenser is free-standing, attach the rubber feet to the tubular frames.
2. If wall-mounted, fit the mounting brackets to the rear legs using the provided screws and nuts.
3. Attach the top handle to the top of the tubular frames.
4. Connect the tubular frames to the cross tube without fully tightening the screws yet.
5. Attach the cutting blade to the front legs of the tubular frames with springs.
6. Secure all screws and nuts.
7. Insert bolts through the front legs and secure with washers and nuts.
8. Add wing nuts, washers, hubs, and tape reels onto the bolts.
9. Fit paper washers, cutting blade spring, and paper holding spring to the paper bar.
10. Place the paper bar between the tubular frames and secure with knobs.

Frequently Asked Questions (FAQ)

• Q: Can I use rolls larger than 450mm with this dispenser?
  A: No, this dispenser is designed to accept rolls up to 450mm only. Using larger rolls may cause operational issues.

• Q: How do I replace the cutting blade?
  A: To replace the cutting blade, carefully unscrew and remove the existing blade, then attach the new blade following the assembly instructions provided in the manual.

MASKING PAPER DISPENSER 450MM ROLL MODEL NO: MK65.V3

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

• Ensure the dispenser is on a reasonably flat, level floor or wall mounted securely before loading.
• Ensure that all fittings are tight and secure.
• Be aware that the paper cutting blades are sharp, handle with care.
• DO NOT use the dispenser for any purpose other than that for which it is designed.
• DO NOT sit or stand on the dispenser.

INTRODUCTION

Single roll dispenser accepts rolls up to 450mm and can be used floor standing or wall mounted. Automatically applies adhesive tape to edges of masking paper.

CONTENTS

See fig.3 overleaf.

ASSEMBLY

NOTE: Numbers in brackets refer to item numbers in fig.3. fig.2 If dispenser is to be free standing fit the four rubber feet to the tubular frames (1).

1. If dispenser is to be free standing fit the four rubber feet to the tubular frames (1).
2. If the disnenser is to be bench or wall mounted fit the two mounting brackets (9) to the rear leas of the tubular  frames (1), using M16 screws (15), M6 washers (14) and M6 nuts (13). Fit two of the feet to the front legs of the tubular frames (1).
3. Attach the top handle (2) to the top of the tubular frames (1) using M8 screws (12) and M8 washers (11).
4. Attach the two tubular frames (1) to the cross tube (4) using M8 screws (12) and M8 washers (11). DO NOT fully tighten screws at this stage.
5. Fit cutting blade spring (10) to either end of the cutting blade (3), as shown in fig. 1.
6. Fit cutting blade (3) to upper holes in front legs of tubular frames (1) using M16 screws (15), M6 washers (14) and M6 nuts (13).
7. Tighten all screws/nuts.
8. Insert bolts (18) through front legs of tubular frames (1) and tighten in place using M6 washers (14) and M6 nuts (13).
9. Thread a wing nut (17) onto each bolt (18) with the wings towards the frame leg.
10. Slide washer (14) and hub (20) onto each bolt (18) and then fit tape reels (19) onto hubs (20) with open sides towards tubular
11. frame (1) legs.
12. Position tape reels (19) with washer (14) and wing nut (17).
13. Fit paper washers (6), cutting blade spring (10) and paper holding spring (5) to paper bar (8) as shown in fig.2.
14. Locate paper bar (8) between bars of tubular frames (1) and retain with knob (16).

OPERATION

1. Remove paper bar (8) from frame and remove washers (6), springs (5) and paper holding washers (6).
2. Slide paper bar (8) through centre of masking paper roll so that, when reinstalled in frame, paper will come from top of roll towards front of dispenser.
3. Replace washers (6), springs (5) and paper holding rings as shown in fig.2, at each end of roll.
4. If two narrow rolls are used fit one spring and washer per roll and use the two extra paper holding rings for the extra roll..
5. Refit paper bar, complete with paper roll, to frame assembly. Position roll in centre of bar and fix in place by tightening screws in paper holding rings (7).
6. Thread leading edge of paper between cutting blade spring (10) and guide edge of cutting blade (3), see fig.1.
7. Press masking tape rolls onto tape reels (19) so that tape leaves bottom of rolls towards the rear of the dispenser. Rolls may be positioned relative to the masking paper edges by adjusting wing nuts.

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on technical@sealey.co.uk or 01284 757505.

Important: No Liability is accepted for incorrect use of this product.

Warranty

Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 sales@sealey.co.uk
www.sealey.co.uk

© Jack Sealey Limited
Original Language Version
MK65.V3 Issue1 08/11/23

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>