BASSBOSS AT212-MK3 Dual 12 2 Way Powered Loudspeaker User Manual

May 15, 2024
BASSBOSS

BASSBOSS logo AT212-MK3
Dual 12” 2-Way
Powered Loudspeaker
User Manual

Overview

The AT212-MK3 is a very high-output, self-powered, internally processed, bi- amplified, 2-way, broadrange loudspeaker. The cabinet is lightweight, the setup is easy and the output is smooth with a natural, musical character. The remarkable power and efficiency of the AT212-MK3 make it ideal for providers who want to deliver high sound pressure levels but prefer not to move heavy cabinets. Intended for use with a subwoofer system to complete a 3-way active full-range system, the AT212-MK3 has a tall, slim design that allows the HF horn to stand above crowds when the cabinet is stacked on subwoofers.
The light weight of the cabinet makes stacking by one person possible. The AT212-MK3 cabinets weigh only 99 lbs. The AT212-MK3 is a vented cabinet that features two high-efficiency 12” woofers.
The woofers feature 3.5” voice coils, Neodymium magnets, cast aluminum baskets and ultra-light cones. The compression driver also features a Neodymium motor structure with a 3” voice coil. It is mated to a 1.4” throat, cast aluminum horn. The horn is rotatable, providing 80 x 60 degree coverage for multiple applications including ground stack and horizontal or vertical flying.
The AT212-MK3 is the ultimate in plug and play, with universal voltage compatibility and no need for any outboard gear, other than a sound source. The built-in processing features presets that allow it to run in multiple configurations. Each preset offers advantages that suit specific applications and preferences.
Power is supplied by an amplifier that can deliver output peaks of 163V, to provide amazing dynamic resolution and impact. The fully integrated and comprehensive digital processing ensures smooth response and reliable operation thanks to meticulous filter alignments and five-stage limiters that protect the drivers from excessive excursion, thermal overload and clipping. The amplifier features a large heat sink and 2 temperature-controlled fans to ensure consistent operation, even under the most extreme conditions.
The cones are waterproofed to protect them from accidental exposure to moisture such as rain or spilled beverages. Weather resistant, IP65 rated power connectors, an internally sealed input section and waterproof-treated cones are provided to allow operation where rain might be encountered.
The cabinet is built from 18mm and 15mm Birch plywood. It features an 18mm baffle and 18mm top and bottom, with 15mm sides, port walls and braces, all assembled with dado joinery. The cabinet includes 4 steel bar-handles, 4 internally braced steel M10 fly points and a 35mm (1-3/8”) cast metal pole socket.
Although the AT212 cabinet is equipped with a 35mm steel pole socket, DO NOT use this speaker on a tripod or extension pole. This socket is to be used with a special, short section of pole to prevent it from moving once stacked on a subwoofer.
The MK3 features an all-new DSP. The comprehensive suite of processing includes multiple presets, each including multiple protection systems and limiters to prevent driver overload in as many ways as possible, including thermal, excursion and clipping. There are five levels of protection that actively prevent overheating of the voice coil, minimize long-term thermal compression and limit excursion. Because they operate in 5 different modes, the limiters are sophisticated enough to have a largely unnoticable effect on the transient response and allow the subwoofer to deliver peak output safely. Each preset has a specific high-pass filter frequency and alignment filters that ensure it’s output is always phase coherent with any BASSBOSS sub. No matter which preset you choose, your BASSBOSS ubs and tops will always play in harmony.
The full-range mode, Preset 1, provides response down to 50Hz (-3dB). Each successive preset filters the lows out at higher frequencies. As low-frequency demand is reduced, higher sound levels can be achieved, allowing the AT212-MK3 to be used above multiple subwoofers.
Not including Cardioid, there are up to 56 possible combinations when MK3 tops are used with MK3 subs, but don’t worry, all are compatible. You can’t choose a “wrong” preset, you simply choose the combination you like best.
The new DSP features an Ethernet interface. This can be used to control the cabinets from a computer or to load software or firmware updates. The ethernet connectivity, in conjunction with the new DSP board, will allow signal to be sent via Milan AVB. (Firmware updates will provide access to this feature.)
Within the software, multiple cabinets can be grouped together, allowing them to respond to commands simultaneously. This permits the levels of groups of loudspeakers to be adjusted together, and yet independently from the levels of other groups of loudspeakers. In addition to individual and grouped level controls, presets can be loaded and signal levels and temperatures can be monitored. Each cabinet includes a two-port switch, so multiple cabinets can be chained on the same data cable.
The MK3 DSP features storage capacity of up to 100 presets, eight of which can be accessed at the touch of a button with no need for a connected computer. The eight directly accessible presets are compatible with all the presets in the MK3 Top Boxes and are also compatible with previous generation tops and subs.

Quick Start Guide

  1. Ensure the cabinet is secure and stable.
  2. Connect signal via the XLR-F input.
  3. Connect the XLR-M connector to additional subs or tops.
  4. Connect the mains power and verify the “Ready” LED is lit.

BASSBOSS systems are easy to set up quickly. The best possible results are achieved consistently because of the integrated nature of the designs. All BASSBOSS loudspeakers are complete, integrated systems, featuring the cabinet, transducer, amplifier and a comprehensive suite of processing. Setup is particularly easy because the products integrate with each other.
Provided the cabinets are physically aligned, any BASSBOSS sub can be combined with any BASSBOSS top and their outputs will be phase-coherent. This means no cancellations and no gaps in the response at the crossover frequency, regardless of which preset is selected.
The on-board BASSBOSS processing allows for the following:
Any BASSBOSS powered subwoofer can be combined with any other BASSBOSS Powered subwoofer and their outputs will sum coherently. (i.e.: in phase with each other.)
Any BASSBOSS powered subwoofer or combination of BASSBOSS powered subwoofers can be combined with any BASSBOSS powered top and their outputs will sum coherently through the crossover region.
HOWEVER only one model of top should be used at a time. An assortment of different tops cannot be stacked together and still achieve coherence and clarity.
The following tops should be used individually, i.e. should NOT be arrayed:
AT312 (Co-axial point-source Main)
DiaMon (Co-axial point-source satellite)
SV9 (2-way monitor with Satellite mode)
The following tops can be used in arrays:
MFLA (Medium Format Line Array, up to 20 cabinets can be arrayed)
AT212 (Horizontally arrayable when necessary)
DV12 (Arrayable in PAIRS ONLY with the upper box of the pair inverted.)
Outboard Processing Warning
Third-party outboard processing (Drive Racks, etc.) are not recommended and are not necessary with BASSBOSS MK3 series powered loudspeakers. Outboard processing will not improve, and will very likely degrade the sound quality, reliability and output capacity. Using external processing inappropriately can cause driver damage that is not covered by warranty.
The internal processing can accomplish everything an external processor could accomplish, butwithout degrading the sound quality and without putting components at risk. Before considering  using an outboard processor, contact BASSBOSS customer service with your use-case scenario for assistance in setting up the internal processing to achieve your goals.
Setup Procedure
Once the the cabinet is in the desired location, signal cables should be connected via the XLR-F input.
It’s recommended to run balanced signal cables to minimize the chance of noise and ground-loop hum.
The incoming signal should be unprocessed because all the necessary processing is done in the builtin DSP.
The signal should be run directly from the outputs of a mixer or controller.
The XLR-M connector provides a full-range, unprocessed, pass-through connection to additional cabinets. This output can be connected to additional subs or tops. Up to 12 cabinets can be connected on a single output from a mixer or controller.
Connecting the mains power. The power connector is a Neutrik PowerCON TOP waterproof type. The power connector inserts with the silver tab rotated counter clockwise from vertical, at about the 10:00 position, and once inserted, rotates clockwise to the 12:00 position to lock in place. Once locked, this connector is waterproof.
This connector also serves as the power switch. To disconnect and remove the connector, pull back on the silver tab to unlock it and rotate it counter clockwise. Once rotated to the insertion angle, the connector can be removed.
When connecting and disconnecting, no force should need to be applied. If the connector doesn’t insert and rotate smoothly, either it’s in the wrong position or it’s damaged and should be replaced. Always use a grounded outlet. The supplied power cord includes a standard grounding NEMA 5-15 (Edison) 120-Volt US wall plug. In unfamiliar locations it’s recommended to verify the correct wiring of outlets before powering your system.
It’s highly recommended to connect all signal and power cords to the speakers before plugging the power cords into mains outlets. When your speaker is powered on, you’ll see all the indicator lights turn on and then show the system’s current status.
Although the AT212 cabinet is equipped with a 35mm steel pole socket, DO NOT use this speaker on a tripod or extension pole. This socket is to be used with a special, short section of pole to prevent it from moving once stacked on a subwoofer.
Operation & Controls
There are 2 controls on the amplifier.

  1. Input
    This knob adjusts the input level from -72dB to -0dB. To avoid distortion and clipping, make sure the input signal doesn’t exceed +22dB and the output doesn’t reach clipping before you achieve the desired sound level.
    While the amplifier has built-in limiters and safety features to protect itself and the speaker, it can’t protect the speaker from distorted incoming signals. The amplifier will simply amplify the clipped signal, which can do the same damage as clipping an amplifier. Since it’s essentially impossible for these amplifiers to clip, signal-level clipping is the most common cause of damage to these speakers. If you hear distortion, lower the input level right away.

  2. Preset Select
    Pressing the Preset Select button cycles through presets 1-8, and pressing it again after preset 8 returns to preset 1. Each preset includes all necessary low-pass and high-pass filters at the selected frequencies and all the necessary alignments to maintain phase coherence in the crossover range when used with other BASSBOSS powered speakers.
    Presets help you fine-tune the balance between the subwoofers and top speakers. More details on the different combinations are on page 7.

Indicator LEDs

Indicator LEDs – Left side, bottom to top:
Ready: Indicates that power is on and the system is ready to play.
Signal: Indicates the presence of input signal.
-12dB: Indicates there is 12dB of headroom remaining before reaching maximum output.
-6dB: Indicates there is 6dB of headroom remaining before reaching maximum output.
Limiting: Indicates one of the channels is reducing the incoming signal level to prevent overdrive.
Overheat: Indicates the amplifier is reducing output to prevent shut-down from overheating.
Protect: Indicates the amplifier is shut down due to a condition that could cause further damage.
The Protect LED also is engaged when the system has been muted via the software.
Comm Link: Indicates communication is active on the LAN connection(s).
Indicator LEDs, Right Side, Bottom to top:
Presets 1-8 – The illuminated LED indicates the corresponding preset is loaded.

How to Use the Presets

Setting the low-pass filter frequency on the subwoofer to match the top cabinet’s high-pass filter frequency and balancing their levels will achieve the smoothest sound across the frequency range.
There are no incompatible combinations.
Selecting high numbered presets on subs with low-numbered presets on tops will result in increased system output in the overlap range, which can be helpful in some situations but can also result in a “boomy” sound.
When the subwoofer levels are to be run higher than tops levels, (which is almost always) the effective crossover moves higher in frequency. If you intend to run your system “bass-heavy ” it’s recommended to run lower-numbered presets on the subs and higher-numbered presets on the tops to avoid an excessively “boomy” sound.
Selecting low-numbered presets on subs with high-numbered presets on tops may result in a lack of “punch” in certain combinations. This is most likely when not enough level is available from the subwoofer(s).
When not enough output is available from the sub(s), using a preset combination with overlap can help provide a little more bass level but it does limit the maximum level of the tops due to the added demand for low- frequencies from the tops.
It’s recommended that you try several, if not all, combinations when first setting up to determine which combination works best in each environment. You will likely choose different combinations for wood floors, concrete floors and outdoors.
Experiment with different combinations to dial in your preferred combination in different environments.BASSBOSS AT212-MK3 Dual 12 2 Way Powered
Loudspeaker - preferred combination Pre-Installed Onboard Presets
High-pass and low-pass filters with included phase compensation.
Preset 1: 45Hz high-pass filter
Recommended for use when no sub is available.
Peak output is restricted to prevent low frequencies damaging the loudspeaker.

  • Preset 1: 45Hz high-pass filter.
  • Preset 2: 55Hz high-pass filter
  • Preset 3: 65Hz high-pass filter
  • Preset 4: 75Hz high-pass filter
  • Preset 5: 85Hz high-pass filter
  • Preset 6: 95Hz high-pass filter
  • Preset 7: 105Hz high-pass filter
  • Preset 8: 115Hz high-pass filter

With their levels matched, when the low-pass filter frequency selected on the subwoofer is matched with the high-pass filter frequency selected on the Top cabinet, the smoothest frequency response should be achieved.
Additional presets are accessible through software. See “How to Use the Presets” section for more information. New presets will be available for download at bassboss.com/software as they are developed.
To be notified when new presets are released register your gear at: www.bassboss.com/support Instructions on linking to your computer for remote monitoring and control: www.bassboss.com/software
Information and setup tips about how to get the best and most out of your system: bassboss.com/edu
Power Distribution
Connect no more than one 5000W or two 2500W subwoofer amplifiers to a single 20A circuit. If you need to share circuits, don’t exceed two BASSBOSS single- driver subwoofers or one double-driver subwoofer, along with one or two top speakers, on the same circuit.
Although amplifiers for tops and subs may be specified to have the same “power ” capacity, in practice, amplifiers used for tops applications tend to draw significantly less current. Subwoofers draw far more current than tops due to the demands for bass level and the duration of the notes.
All MK3 amplifiers can operate on mains supply from 100 to 250VAC. To connect to voltages other than 120V, a different mains connector plug must be used. Contact your salesperson for information about purchasing cables for alternate voltages.
Pass-through Power connections can be used to power additional cabinets. With optional True 1 TOP cables, power can be linked between subs and tops. Do not connect equipment that will draw more than 15A on a single power outlet. Contact your salesperson for information about linking power cables.
Avoid powering all subwoofers on the same circuit. Instead, use separate circuits for each subwoofer and top speaker combo to help prevent overloading a single circuit and tripping a breaker.

Troubleshooting

If, after following the previous instructions for setup, you have no output from the loudspeaker:
Verify that the green Ready LED is lit. If NOT lit, check the following:

  1. Is the power cord plugged into a live outlet?
  2.  Is the Neutrik powerCON connector rotated into the locked position?

If the green Ready LED is lit, check the following:

  1. Is the red Protect LED illuminated? The unit may be in protect mode or set into mute via software.

  2. Is the signal cable connected to the input?

  3. Is the signal cable connected to an operating output at the other end?

  4. Is there signal flowing to the input? Check the integrity of the cable against a different cable.

  5. Is the volume knob turned all the way down or at a very low level?

  6. Is the signal flowing to the input full-range?
    Filters in the signal may remove the operating frequencies of the loudspeaker receiving them.

  7. If you’re connected via LAN, check the level and filter settings in the software.

Specifications

Acoustical

Loudspeaker Description: High-output 2-Way Broad-range Main
Frequency Response (±3 dB): 50 – 18,000 Hz
Max Sustained Output: 136 dB SPL, 1m
Maximum Measured Output: 142 dB SPL, 1m
Nominal Dispersion (°H x °V): 80 x 60 (Rotatable)

Electrical

Amplification: 3200 Watt Two-Channel Class D Amplifier; 2400W LF – 800W HF
Processing: Integrated comprehensive DSP including high-pass, low-pass,

parametric EQ, phase alignment and multi-band limiting
Electrical Connectors, Amplifier:| Neutrik Powercon True 1 TOP in and through
Electrical Connector, Mains:| NEMA 5-15 (Edison)
Voltage Operating Range:| 100-240V AC, 50-60Hz (Auto-sensing, auto switching universal supply)
Current Draw, Nominal:| 4.6A @ 120 volts, 2.3A @ 220V (Average with music program)
Display:| LEDs for Power on/ready, Signal, -12dB, -6dB, limiter active, Thermal, Protect and LAN link active. Eight LEDs indicating selected preset
Signal Input Connector:| XLR-F
Signal Output Connector:| XLR-M pass-through
LAN Connectors:| EtherCON RJ45 (x2) with 2-port Ethernet switch

Physical

Enclosure Type:| Self-powered, bi-amplified, 2-way broad-range. Direct radiating vented LF section, Horn-loaded HF section
---|---
Transducer, LF:| 2 x 12” diameter (300 mm) Neodymium motor woofer with 3.5” (88mm) voice coils
Transducer, HF:| 1 x 1.4” throat Neodymium motor compression driver with 3” (76mm) voice coil on cast aluminum 80 x 60 degree horn
Cabinet Construction:| CNC machined 18mm/15 mm multi-ply Birch plywood with internal bracing and damping 4 steel bar handles and a 35mm pole socket
Suspension Points:| 4 x internally braced M10 threaded mounting points
Dimensions (HxWxD):| 48” x 14.5” x 18” (122 cm x 36.4 cm x 45.4 cm)
Net Weight:| 99 lbs. (45 kg)
Shipping Weight:| 109 lbs. (50 kg)
Exterior Finish:| Rugged, weatherproof, black, textured, bonded high-pressure polyurea coating
Grille:| Perforated, powder coated steel

Optional

Shoulder Eye Bolts: Use when flying the cabinets vertically
Side-pull anchors: Use when flying the cabinets horizontally
Cover: Heavy-duty padded nylon transport cover with velcro closure
Loop-through PowerCON TOP: Power jumper for chaining power between adjacent

cabinets
Online Information:| bassboss.com/at212

Our proactive philosophy causes specifications to be subject to change whenever improvements are made.

Warranty

WARRANTY INFORMATION | Our fully-transferable warranty covers all BASSBOSS products.
STANDARD CABINET WARRANTY
BASSBOSS loudspeaker cabinet integrity, including all joinery, fasteners, handles and wood, is warranted against defects in materials and workmanship for a period of six (6) years from the date of purchase. This warranty does not cover items that are intended to wear and can be replaced if worn or damaged. Examples of items not covered by this warranty are cabinet feet, grilles and the finish or coating applied to the cabinet.
ENHANCED COMPONENT WARRANTY
BASSBOSS amplifiers and electronic components are covered against failures due to defects in materials and/or workmanship for a period of three (3) years from the date of purchase.
TRANSDUCER WARRANTY
Transducers are covered against failures due to defects in materials and/or workmanship for two (2) years from the date of purchase.
WARRANTY SUPPORT
Warranty support is a service, and part of that service includes helping you prevent failures and minimize repair and shipping costs. Please contact BASSBOSS immediately if you observe an issue.
Please do not ship products without obtaining a return authorization number (RMA) by contacting BASSBOSS at bassboss.com/support. If you need to ship your speaker for service, BASSBOSS technicians will provide assistance on shipping and packaging requirements specific to your service needs.
WARRANTY LIMITATIONS
During the warranty period, if your loudspeaker malfunctions or fails due to any defect in components or manufacturing, the failed parts will be repaired or replaced. This warranty does not extend to damage resulting from improper installation, misuse, neglect or abuse. Warranty coverage and eligibility will be determined upon inspection by BASSBOSS personnel. This warranty does not cover labor other than that authorized and performed by BASSBOSS personnel. Service will be performed upon the return of the failed unit, together with its original sales receipt or other proof of purchase, to BASSBOSS or an Authorized Service Facility. Purchaser is responsible for all costs of shipping and handling. Cosmetic damage is specifically excluded from this warranty. This warranty is rendered void if service, repairs and/or modifications are attempted or made by anyone not specifically authorized by BASSBOSS to perform said services. Please contact BASSBOSS or your local BASSBOSS dealer before attempting any repairs and before shipping parts in for service. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

Safety Information

Important information regarding safety and the use of your loudspeakers:
To prevent potentially dangerous exposure to high levels of acoustic pressure, never stand in the immediate vicinity of loudspeakers driven at a high level without hearing protection. Professional loudspeaker systems are capable of causing sound pressure levels detrimental to human health.
When a transducer capable of producing high sound levels is being used, it is necessary to wear ear plugs or protective earphones to prevent hearing damage.
Even seemingly non-critical sound levels (from approximately 95 dB SPL) can cause hearing damage if people are exposed to it over a long period. Anyone exposed to these levels should use appropriate hearing protection devices. System and venue owners and operators are encouraged to make hearing protection devices available to all customers and staff members.
In order to prevent accidents when setting up the loudspeakers or loudspeaker stands, make sure they are standing on a firm surface. Ensure that all additional hardware, fixings and fasteners used for installation or mobile deployment are of an appropriate size and load safety factor.
Only use included, factory installed, internally secured M10 fly points when supporting cabinets. (Not all models include these features.) Only use appropriately load-rated hardware. Never hang loudspeakers from handles. Never drill or screw into cabinets to attach lifting points.
Pay attention to the manufacturers’ instructions and to the relevant safety guidelines. Regularly check the loudspeaker housings and accessories for visible signs of wear and tear, and replace them when necessary. Regularly check all load bearing bolts in the mounting devices.
Caution: Loudspeakers produce a static magnetic field even if they are not connected or are not in use. Therefore make sure when erecting and transporting loudspeakers that they are nowhere near equipment and objects which may be impaired or damaged by an external magnetic field.
A distance of 3 feet (1m) should be maintained between loudspeakers and sensitive equipment such as CRT monitors or magnetic storage media.
Never attempt to carry out any operations, modifications or repairs that are not expressly described in this manual. Contact your dealer or BASSBOSS support if the product is not functioning properly. The audio system must comply with current local standards and regulations regarding electrical systems.
For installation purposes, BASSBOSS strongly recommends that this product be installed by a qualified, professional installer who can ensure correct installation and certify that it is installed in compliance with the regulations in force.

Important Notes

Shielded data cables must be used.
To minimize the occurrence of noise and interference, always use shielded signal cables. Avoid routing signal or data cables close to equipment that produces high-intensity electromagnetic fields such as transformers, power cables and loudspeaker wires.
Do not coil excess power cable. Do not coil or wrap power cables and signal or data cables together.
WARNING
This is a class A product. In a domestic environment, this product may cause radio interferences, in which case the user may be required to take corrective measures.
FCC Compliance Notice
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.
Manufacturer
True Lee Loudspeakers | BASSBOSS 2028 E Ben White Blvd. #240-8220 Austin TX 78741 We declare, under our sole responsibility, that to the best of our knowledge to which this declaration relates, our products are in conformity with the applicable requirements.
Product: AT212-MK3 Loudspeaker Intended use: Professional Audio LoudspeakerBASSBOSS AT212-MK3 Dual 12 2 Way Powered Loudspeaker -
fig

Need more assistance?
We’re here to help.
bassboss.com/support
bassboss.com

Documents / Resources

| BASSBOSS AT212-MK3 Dual 12 2 Way Powered Loudspeaker [pdf] User Manual
AT212-MK3 Dual 12 2 Way Powered Loudspeaker, AT212-MK3, Dual 12 2 Way Powered Loudspeaker, 2 Way Powered Loudspeaker, Way Powered Loudspeaker, Powered Loudspeaker, Loudspeaker
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals