tp-link tapo Smart Temperature and Humidity Sensor User Guide

tp-link Tapo T310 Smart Temperature and Humidity Sensor

Meet Your Temperature and Humidity Sensor

Measure the temperature and humidity of the environment and send you instant notifications when the environment changes. It is suitable for green houses, bedrooms, nursery, incubators, and wine cellars.

**Before You Start

**

A Tapo Hub is required. Make sure your Tapo Hub is successfully added via the Tapo app.

Power Up Your Sensor

Remove the battery insulation tab to power up your sensor. The LED should blink.
Note: If the LED is not blinking, use a pin to press the Reset button for 5 seconds to reset your sensor and enter pairing mode.

Set Up Your Sensor

Open the Tapo app and tap the button. Select Sensors and then your model. Follow the app instructions to complete setup.

Test Your Sensor

Take your sensor to the preferred location.

Option 1 Single press the Reset button. Your hub should make a voice prompt.

Option 2 Blow on the sensor detector. The temperature and humidity displayed on the Tapo app should change.

Place Your Sensor

Option 1: Hang with the Lanyard

Option 2: Use Adhesive Magnets

• a. Stick the included adhesive magnets to the back panel.
• b. Magnetically attach the sensor to metallic surfaces.

Option 3: Use 3M Adhesives

• a. Stick the included 3M adhesives to the back panel.
• b. Stick the sensor to your preferred location.

How to replace the battery

1. Use a pin to press and remove the cover.
2. Replace the battery with a fresh cell.
3. Put the cover back.

Need some help?
Visit www.tapo.com/support/ for technical support, user guides, FAQs, warranty & more

Warning

• This product contains a coin / button cell battery. If the coin / button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
• Keep new and used batteries away from children.
• If the battery compartment does not close securely, stop using the product and keep it away from children.
• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
• Risk of explosion if the battery is replaced by an incorrect type.
• Do not ingest battery, Chemical Burn Hazard
• Avoid replacement of a battery with an incorrect type that can defeat a safeguard.
• Avoid disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
• Do not leave a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; Do not leave a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

Safety Information

• Keep the device away from water, fire, humidity or hot environments. Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Do not use the device where wireless devices are not allowed.
• Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
• TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU, and (EU) 2015/863.
• The original EU declaration of conformity may be found at https://www.tapo.com/en/support/ce/
• TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.
• The original UK declaration of conformity may be found at https://www.tapo.com/support/ukca/

For EU/UK Region:
Operating Frequency / Nominal Operating Frequency / Max Output Power:

• 863~865MHz / 863.35MHz / 25mW (e.r.p)
• 863~865MHz / 864.35MHz / 25mW (e.r.p)
• 868~868.6MHz / 868.35MHz / 25mW (e.r.p)

FCC STATEMENT

FCC compliance information statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

References

• Regulatory Compliance | Tapo
• UKCA | Tapo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>