LTECH P5 DIM/CT/RGB/RGBW/RGBCW LED Controller Instructions
- May 15, 2024
- LTECH
Table of Contents
LTECH P5 DIM/CT/RGB/RGBW/RGBCW LED Controller
Specification
DIM/CT/RGB/RGBW/RGBCW LED Controller
- Small size and light weight. The housing is made from V0 flame retardant PC materials from SAMSUNG/COVESTRO.
- With soft-on and fade-in dimming function, enhancing your visual comfort.
- 2.4GHz wireless signal , no signal wire needed.
- 5 channels with constant voltage output.
- Control DIM, CT, RGB, RGBW, RGBCW light.
- Work with a MINI series RF 2.4GHz remote.
- Built-in 12 dynamic modes.
- One controller can be controlled by 10 remotes.
- Sync dynamic effects between controllers in the same group/zone.
Technical Specs
| Model | P5 |
|---|---|
| Input Signal | RF2.4GHz |
| Input Voltage | 12-24V ____ |
| Output Voltage | 12-24V |
| Load Current | 3A×5CH Max. 15A |
| Load Power | 180W@12V 360W@24V |
| Protection | Over Temperature Protection, Anti Reverse Connection Protection |
| Working Temp. | -25°C ~ 50°C |
| Dimension | L91×W37×H21(mm) |
| Package Size | L94×W39×H22(mm) |
| Weight(G.W.) | 46g |
Product Size
Unit: mm
Terminal Description
Pair the controller
Pair the controller using the button
Step 1
Short press the ID learning button on the controller and the load light
flashes . Please complete the following operations in 15s.
Step 2
Pair the controller with a MINI series remote:
Single-zone MINI remote: Long press the ON/OFF button until the
controller’s load light flashes fast.
Multi-zone MINI remote: Long press any zone button until the
controller’s load light flashes fast.
Step 3
The controller’s load light flashes fast then stops flashing, which means
pairing is successfully done.
Unpair the controller
Unpair the controller using the button
Long press the ID learning button on the controller for 10s. The load light
flashes 5 time, which means the paired controller have been removed from the
remote.
Pair/unpair the controller by powering it on
Step 1
Power off the controller.
Step 2
Pair the controller with a MINI series remote:
Single-zone MINI remote: After powering on the controller, long press the
ON/OFF button within 3s until the controller’s load light flashes fast.
Multi-zone MINI remote: After powering on the controller, long press any
zone button until the controller’s load light flashes fast.
Step 3
The controller’s load light flashes fast then stops flashing, which means
pairing is successfully done.
Unpair the controller by powering it on
Power on and off the controller for 10 consecutive times. The light flashes 5
times which means the paired controller have been removed from the remote.
Attentions
-
Product installation and commissioning should be done by a qualified professional.
-
LTECH products are and not lightning proof non-waterproof (special models excepted). Please avoid the sun and rain. When installed outdoors, please ensure they are mounted in a water proof enclosure or in an area equipped with lightning protection devices.
-
Good heat dissipation will extend the life the product. Please install the product in a environment with good ventilation.
-
When you install this product, please avoid being near a large area of metal objects or stacking them to prevent signal interference.
-
Please keep the product away from a intense magnetic field, a high pressure area or a place where lightning is easy to occur.
-
Please check whether the working voltage used complies with the parameter requirements of the product.
-
Before you power on the product, please make sure all the wiring is correct in case of incorrect connection that may cause a short circuit and damage the components, or trigger a accident.
-
If a fault occurs, please do not attempt to fix the product by yourself. If you have any question, please contact the supplier.
-
This manual is subject to changes without further notice. Product functions depend on the goods. Please feel free to contact our official distributors if you have any question.
Warranty Agreement
Warranty periods from the date of delivery : 5 years.
Free repair or replacement services for quality problems are provided within
warranty periods.
Warranty exclusions below:
- Beyond warranty periods.
- Any artificial damage caused by high voltage, overload, or improper operations.
- Products with severe physical damage.
- Damage caused by natural disasters and force majeure.
- Warranty labels and barcodes have been damaged.
- No any contract signed by LTECH.
- Repair or replacement provided is the only remedy for customers. LTECH is not liable for any incidental or consequential damage unless it is within the law.
- LTECH has the right to amend or adjust the terms of this warranty, and release in written form shall prevail.
Update Log
| Version | Updated Time | Update Content | Updated by |
|---|---|---|---|
| A0 | 20231227 | Original version | Yang Welling |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>