better bathrooms Thermo Toilet Bidet User Manual

better bathrooms Thermo Toilet Bidet

TROUBLESHOOTING

USER MANUAL

Thermo Toilet Bidet

• ✓ Dual Nozzle Sprayer
• ✓ Hot and Cold Water Inlets
• ✓ Adjustable Water Temperature
• ✓ Eco- friendly Design
• ✓ Quick Installation Design
• ✓ Hot and Cold Water Inlets
• ✓ Adjustable Water Temperature
• ✓ Eco- friendly Design
• ✓ Quick Installation Design

PRODUCT INTRODUCTION

ACCESSORIES

ASSEMBLY DIAGRAM

INSTALLATION

1. Step 1 – Turn Off Water Supply and Empty the Toilet Tank
   Turn off the toilet tank water supply. Flush toilet and hold down the handle to completely empty the toilet tank.

2. Step 2 – Remove the Toilet seat
   Lift the hinge tabs and use a flathead screwdriver to unscrew the toilet seat bolts while holding the nuts on the underside of the bolts in place.

3. Step 3 – Mount Your Bidet on the Toilet
   Place the bidet attachment on the toilet. Rotate the adjustment plates accordingly to line up properly with the holes on the toilet bowl.

4. Step 4- Reattach Your Toilet Seat
   Reattach the toilet seat on top of the bidet attachment and secure it using the original toilet seat hardware.

5. Step 5 – Connect the Hot and Cold Water Hose to the Bidet Water Inlets
   Connect the cold water braided metal hose to the cold water bidet inlet. Connect the 3/8″ end of the hot water PU hose to the hot water bidet inlet.
   NOTE: If you do not need hot water temporarily, please seal the hot water inlet with the Water Inlet Cap.

6. Step 6 – Install the Cold Water T-adapter to the Toilet Tank and Connect the Braided Metal Hose
   Disconnect the water supply hose from the toilet tank.
   Insert the black cone washer at the top of the cold water T-adapter. Connect the top of the cold water
   T-adapter to the toilet tank and the bottom of the T-adapter to the toilet tank water supply hose. Connect the braided metal bidet hose to the cold water T-adapter.

7. Step 7 – Turn off the Sink Hot Water Supply
   Turn off the sink hot water supply (located underneath or near the sink) to stop the flow of water.

8. Step 8 – Install the Hot Water T-adapter to the Hot Water Sink Valve
   Disconnect the sink hot water supply hose from the sink valve.
   Insert the black rubber washer at the bottom of the hot water T-adapter. Connect the bottom of the hot water T-adapter to the hot water sink valve and the top of the T-adapter to the sink hot water supply hose.

9. Step 9 – Connect the Hot Water PU Hose to the Hot Water T-adapter
   Evaluate the right length of PU hose you need, and cut off the spare. Connect the 8mm end of the PU hose to the 8mm barb of the hot water T-adapter.

10. Step 10 – Turn on the Toilet Tank Water Supply and Sink Hot Water Supply
    Turn on the water supply, make sure there are no leaks. Now. you are ready to use the bidet for the first time.

PREPARATION BEFORE INSTALLATION

• Install Batteries Before Install the Bidet Attachment
  The bidet attachment requires 2 AA 1.5 volt batteries to activate the temperature display function. (Not included in the package) Rotate the ‘Function Control Knob’. make sure the temperature is displayed.

• NOTE: This product does not have heating function. it just displays the temperature. It’s safe. (36·C=97’F. 38’C=100″F. 40’C=704’F)

FUNCTION OPERATION

1. Warm Water Preset
   Rotate the ‘Function Control Knob’ clockwise from ‘OFF’ to ‘WATER PRESET’, the mix water is flowing out while the water temperature displays. When the temperature display keeps stable and reaches your desired, rt is ready for your rear wash or frontal feminine wash.

Adjust Water Temperature

• While the the ‘Function Control Knob’ set to ‘WATER PRESET’, the mix water is flowing out, you can rotate slowly the ‘Water Temperature Control Knob’ to adjust the temperature displayed you desired.
• When the water temperature reaches your desired temperature, it Is ready for your rear wash or frontal feminine wash.

NOTE

1. You don’t need to adjust it every time, it defaults at your last setting.
2. In order to get a better wash experience, please perform ‘Warm Water Preset· before wash, that Is, empty the cold water from the hose at first.
3. While adjust water temperature, the temperature display does not change, what Is the problem?
   • The hot water is not connected or the valve doesn’t turn on.
   • There is a problem with the hot water supply.

Rear Wash

• Rotate the ‘Function Control Knob’ clockwise from ‘OFF’ to ‘WATER PRESET’, then to ‘Rear Wash’ (90-180 degrees). Please rotate slowly, the water pressure can be controlled.

Feminine Wash

• Rotate the ‘Function Control Knob’ anticlockwise from ‘OFF’ to ‘Feminine
• Wash’. Please rotate slowly, the water pressure can be controlled.
• NOTE: If you need warm water, please perform ‘Warm Water Preset’ first.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>