Kira Home Brighton 16 Inch Modern 2-Ring LED Flush Mount Ceiling Light Installation Guide
- May 15, 2024
- Kira Home
Table of Contents
Kira Home Brighton 16 Inch Modern 2-Ring LED Flush Mount Ceiling Light
INSTALLATION
- Before beginning assembly, installation or operation of the product, make sure all parts are present.
- If any part is missing or damaged, do not attempt to assemble, install or operate the product Contact customer service for replacement parts. Loosen screws counterclockwise.
- Open the junction box. The junction box contains three wires: hot (black), neutral (white) and bare ground.
- Connect the two hot wires with wiring nuts one from the light switch cable and the other from the recessed housing). Repeat the step with the two neutral wires. Close the junction box to complete the wiring.
- Put the fixture plate across the screw of the lock, then rotate the fixture plate clockwise and lock it tightly with the screw lock. Use the switch to choose the desired Color Temperature.
- Before beginning assembly, installation or operation of the product, make sure all parts are present. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Contact customer service for replacement parts. Loosen screws counterclockwise.
- Securely mount the fixture plate to the junction box firmly.
- Place Dittuser and tighten the screws clockwise to complete the installation.
- Restore power to the electrical box. Turn the light switch on to activate the fixture.
SAFETY INSTRUCTION
Please read and understand all instructions before operating or installing the product. Failure to do so may lead to electric shock, fire or other injuries that could be hazardous or even fatal.
- Shut off the electricity to the wires that you are working on.
- Do NOT open, no user-serviceable parts inside. Any changes or modifications and applications not expressly approved by the manufacturer could void the user’s authority to operate the equipment and warranty.
WARNING
- RISK OF ELECTRIC SHOCK: Turn the power off before inspection, installation or removal. Properly ground electrical enclosure.
- RISK OF FIRE: Follow all NEC and local codes. Use only UL or IEC-approved wire for input/output connections. Minimum size 18 AWG (0.75 mm2).
- Do not install insulation within 3 inches (76 mm) of luminaire top.
- RISK OF INJURY, RISK OF DAMAGE: Luminaire may fall if the inner bezel is not secured properly to the outer bezel. Ensure that the whole loop is positioned and secured under the washer.
- LED retrofit kit installation requires knowledge of luminaire electrical systems. Do NOT attempt installation if not qualified. Contact a qualified electrician.
- Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings.
- Do NOT exceed the input rating of the luminaire.
- Do NOT make or alter any open holes in an enclosure of wiring or electrical components during installation.
- To prevent wiring damage or abrasion, do NOT expose wiring to edges of sheet metal or other sharp objects.
- This device is not intended for use with emergency exits.
- This retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction.
CAUTION
- RISK OF FIRE: THIS PRODUCT MUST BE INSTALLED BY THE APPLICABLE
- INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
- CONSULT A QUALIFIED ELECTRICIAN TO ENSURE THE CORRECT BRANCH CIRCUIT CONDUCTOR.
- THE LED LUMINAIRE MUST BE CONNECTED TO THE MAINS SUPPLY ACCORDING TO ITS RATINGS ON THE PRODUCT LABEL.
FCC STATEMENT
Connect the fixture to a 120 Volt, 60Hz power source only. Any other
connection voids the warranty.
This device complies with Part 15 of the FCC Rules. Operations are subject to
the following conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. This Class (A) RELD complies with the Canadian standard
ICES-003
NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device, under part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and if not installed
and used by the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct
the interference at his own expense.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>