Kira Home RVL-CP5293-4 Myers 25 Inch 4-Light Modern Adjustable Foyer Chandelier Instruction Manual

: October 30, 2023
: Kira Home

Table of Contents

IMPORTANT SAFETY INSTRUCTIONS
INSTALLATION INSTRUCTIONS
PARTS DIAGRAM
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RVL-CP5293-4 Myers 25 Inch 4-Light Modern
Adjustable Foyer Chandelier
Instruction Manual

IMPORTANT SAFETY INSTRUCTIONS

To avoid injury or damage, mount only on a surface that is sturdy.
To avoid electric shock, make sure the electricity is turned oﬀ at the main circuit breaker panel. If you are replacing an existing ﬁxture, turn oﬀ the following in order: ﬁxture, wall switch, and main fuse or breaker box.
Note: Some types of fuses must be unscrewed to shut the power oﬀ.
If you are unclear as to how to proceed, please consult a licensed electrician.

UNPACK THE FIXTURE: Check the contents of the box. Box should contain all items on the parts diagram.

INSTALLATION INSTRUCTIONS

Secure Mounting Plate (A) to the junction box (not included) using Mounting Screws (B) provided. Ensure the attached Screw Collar Loop (E) is pointing down towards the ﬂoor.
Remove Threaded Ring (F) from Screw Collar Loop (E) by unscrewing it in a counter-clockwise direction. Set Threaded Ring (F) aside.
Place Canopy (D) against the ceiling with Screw Collar Loop (E) protruding through the hole in Canopy (D).
Adjust Screw Collar Loop (E) and the hex nut above it until 3/8″ of the threaded portion of Screw Collar Loop (E) is visible. Remove Canopy (D) and set it aside.
Secure Socket Assembly (K) to Center Rod (L). Secure Pendant Loop (I) to the top of Fixture Body (J) by screwing it in a clockwise direction. Pull through any necessary Wire (H).
Spread out the arms on Fixture Body (J) evenly to create the chandelier design.
Align holes on Top Ring (M) with the top holes on Fixture Body (J) and secure with Decorative Screws (Q).
Align holes on Bottom Ring (N) with the bottom holes on Fixture Body (J) and secure with Decorative Screws (Q).
Assemble one end of Chain (G) to Pendant Loop (I) by opening Quick Link (P) closing it around Pendant Loop (I).
With chain pliers, remove excess Chain (G) to achieve desired hanging length. Once Chain (G) is cut, use wire cutters to cut Wire (H) 10” beyond the length of Chain (G) to allow for easier wire connection.
Weave Wire (H) upwards through every 4-5 links in Chain (G).
Slide Threaded Ring (F) down Chain (G) and Wire (H) with the raised end (ﬂange) facing up towards the ceiling. Slide Canopy (D) down Chain (G) and Wire (H).
Note: Threaded Ring (F) and Canopy (D) will be used to secure the ﬁxture to ceiling at a later step.
Carefully lift the ﬁxture (with the help of a friend). Secure top of Chain (G) to Screw Collar Loop (E) with Quick Link (P).
Insert the end of Wire (H) through the hole in Screw Collar Loop (E) into the junction box.
Using the wire graph below, connect the appropriate wires from the ﬁxture to the corresponding wires in the electrical junction box (not included) and secure Wire Connectors (C). A. Connect the ground wire (bare copper or green) from your ﬁxture to the:
1) ground wire in the junction box, or
2) ground screw in the junction box
B. Connect the BLACK house wire to ﬁxture hot wire that corresponds to diagram (black, round & smooth, white/grey with tracer, brown/gold without tracer).
C. Connect the WHITE house wire to ﬁxture neutral wire that corresponds to diagram (white, ribbed/ridged, white/grey without tracer, brown/gold with tracer).
Place all Wires (H) and Wire Connectors (C) back into the junction box.
Slide Canopy (D) and Threaded Ring (F) up Chain (G) and Wire (H). Place Canopy (D) ﬂush against the ceiling and secure in place by screwing Threaded Ring (F) onto Screw Collar Loop (E) in clockwise direction.
Install bulbs (not included) into the sockets.