OLDE MIDWAY PRO12 Hot Dog Roller Instruction Manual
- May 15, 2024
- OLDE MIDWAY
Table of Contents
OLDE MIDWAY PRO12 Hot Dog Roller
Product Information
Specifications
- Model: PRO12, PRO18, PRO24, PRO30
- Temperature: Varies per model
- Power: 700W, 900W, 1200W, 1400W
- Electric Voltage: 110V
- Rollers: 5, 7, 9, 11
Product Usage Instructions
Assembly Instructions
Inspect Components: Before use, check all parts for damage or missing
pieces.
Attaching Glass Cover:
- Locate and remove screws on the inner sides of the roller base.
- Position the back glass mount onto the roller base and reinsert screws.
- Insert small side glass panels into mounts on each side.
- Place the large curved glass shield into the back mounts.
- Attach stainless steel trim plate over the edge of the top glass.
Operating Instructions
Preparing for Use:
- Apply vegetable oil onto the roller surface before the first use.
- Turn Power Switch ON and wait for the indicator light to glow.
Adjusting Temperature:
Adjust the FRONT and BACK temperature controllers based on the model to
control rollers.
Cooking Hot Dogs:
- Place hot dogs between the rollers using tongs.
- Avoid touching hot rollers.
Cooking Time:
- Cooking time may vary based on temperature and hot dog thickness.
- After approximately 15 minutes, hot dogs should be ready.
Cleaning & Maintenance:
- Clean the hot dog roller after each use.
FAQ
-
Q: Can I leave the hot dog roller unattended while in use?
A: It is recommended to supervise the hot dog roller during operation to prevent accidents. -
Q: How do I know when the hot dogs are cooked?
A: Hot dogs are typically ready after approximately 15 minutes of cooking, but cooking times may vary.
SAFETY WARNING
Misuse of this machine may result in serious injury or death.
READ ALL INSTRUCTIONS BEFORE USING YOUR HOT DOG ROLLER. RETAIN THIS MANUAL FOR FUTURE REFERENCE.
- This hot dog roller is not a toy. Please keep away from children. This machine should not be operated by anyone under the age of 18.
- Do not use machine for anything other than its intended purpose. This machine should never be modified.
- Make sure machine is plugged into a grounded outlet with appropriate electrical supply. Always make sure the wall outlet being used is properly grounded.
- Take proper safety precautions when using this machine.
- Do not touch moving parts. Keep body, hair, jewelry, clothing, etc. away from machine when in use.
- Use only 3-prong grounded extension cords that meet or exceed the electrical rating.
- Always switch POWER OFF on machine before unplugging from outlet.
- Always use controls to operate. Allow hot parts to cool down before moving or cleaning.
- Always place machine on a secure, level, and stable surface.
- This is a freestanding machine and should not be placed in a built-in or recessed area.
- To avoid any risk of electrical shock, do not immerse cord or plug in water.
- Do not place on top of cloth or fabric materials.
- DO NOT CLEAN WITH DETERGENT OR ABRASIVE CLEANERS. DO NOT IMMERSE IN WATER.
SPECIFICATIONS
| Model | Temperature | Power | Electric Voltage | Rollers |
|---|---|---|---|---|
| PRO12 | 0-500 ° F | 700 Watt | 110V | 5 |
| PRO18 | 0-500 ° F | 900 Watt | 110V | 7 |
| PRO24 | 0-500 ° F | 1200 Watt | 110V | 9 |
| PRO30 | 0-500 ° F | 1400 Watt | 110V | 11 |
PARTS & WIRING DIAGRAM
ASSEMBLY INSTRUCTIONS
INSPECT ALL COMPONENTS BEFORE USE. DO NOT ATTEMPT TO USE THE HOTDOG ROLLER MACHINE IF ANY PARTS ARE DAMAGED OR MISSING.
ATTACHING GLASS COVER
Skip to Operating Instructions if Hot Dog Roller DOES NOT have a glass cover.
-
STEP 1:
Locate and remove the pair of screws on the inner left and right sides of the roller base and set aside. -
STEP 2:
Position the back glass mount onto the roller base. Reinsert the screws removed in STEP 1 and hand-tighten, as it may need to be adjusted. Repeat for the remaining 3 mounts. -
STEP 3:
Insert one of the small side glass panels into both the front and back mounts on one side of the machine with the curved side of the glass facing the back (away from the controls). If needed, adjust mounts by sliding forward or backward until the glass is snug; tighten to secure. Repeat for the other side. -
STEP 4:
Place the large curved glass shield into the back mounts pushing gently all the way down into the channel. Check to make sure the edges of the top and side glass pieces are flush. -
STEP 5:
Place the stainless steel trim plate over the edge of the top glass, aligning the holes with the glass. -
STEP 6:
Insert a bolt through the trim plate and glass, then secure with nut. DO NOT OVERTIGHTEN, as this may crack the glass.
OPERATING INSTRUCTIONS
STEP 1:
Before the first use, apply a small amount of vegetable oil onto the surface
of the rollers. Press the Power Switch ON. The indicator light will glow when
the machine has power and will turn off when the temperature has been reached.
NOTE: The machine will become hot very quickly.
STEP 2:
Adjust the temperature controllers, FRONT and BACK. We recommend lower
temperatures until you understand the cooking times.
- PRO12 (5 rollers) FRONT dial controls front 3 rollers – BACK dial controls the rear 2
- PRO18 (7 rollers) FRONT dial controls front 4 rollers – BACK dial controls the rear 3
- PRO24 (9 rollers) FRONT dial controls front 5 rollers – BACK dial controls the rear 4
- PRO30 (11 rollers) FRONT dial controls front 6 rollers – BACK dial controls the rear 5
STEP 3:
ATTENTION: Rollers are HOT – DO NOT TOUCH! Place hot dogs between the
rollers using tongs or other utensil. Do not use your hands.
STEP 4:
After approximately 15 minutes the hot dogs should be ready to eat. Cook times
may vary depending on cooking temperature, thickness of the hot dogs, and
starting temperature (frozen hot dogs may take longer).
STEP 5:
Remove the hot dogs using tongs or other utensil. Do not use your hands.
STEP 6:
Press the Power Switch OFF.
STEP 7:
Unplug from wall outlet. Allow to cool completely before touching or cleaning.
CLEANING & MAINTENANCE
It is recommended that the hot dog roller be cleaned after each use.
- Make sure the machine is turned OFF and it is unplugged.
- Allow the machine to cool completely.
- Do not immerse the cord, plug or any part of the machine in water or other liquid.
- Wipe down rollers and removable drip tray with a damp soft cloth. Do not submerge machine in water or spray water into the machine.
- NEVER USE STEEL WOOL TO CLEAN THE MACHINE, THIS WILL SCRATCH THE SURFACES. Do not use abrasive cleaning agents or chemicals on any part of the machine.
- A food safe glass cleaner can be used to clean the glass.
- After cleaning, dry with a soft cloth. Make sure the unit is completely dry before using again or storing.
Olde Midway features a full line of concession equipment and accessories.
OldeMidway.com