GELE 8036 2 Handle Kitchen Sink Faucet with Side Sprayer Instruction Manual

: May 15, 2024
: GELE

Table of Contents

8036 2 Handle Kitchen Sink Faucet with Side Sprayer
Product Specifications:
Product Usage Instructions:
Installation:
Care and Cleaning:

8036 2 Handle Kitchen Sink Faucet with Side Sprayer

“`html

Product Specifications:

Product Name: GELE Faucet
Installation Type: Two Handle Faucet
Tools Required: Adjustable wrench, Phillips screwdriver, Hex
wrench, Pipe tape, Silicone sealant/Putty

Product Usage Instructions:

Installation:

Shut off water supply and remove the old faucet.
Clean the sink/countertop surface for the new faucet
installation.
Apply plumber’s putty or suitable sealant to the bottom edge of
the undercover.
Align and press the undercover into place.
Insert the faucet through the sink.
Screw the nut onto the shank, leaving a small gap between the
ring and the sink.
Tighten fitting nuts with an adjustable wrench. Do not over
tighten.
If sidespray is not included, connect and tighten hoses with
hot and cold water supply. If sidespray is included, proceed to the
next steps.
Insert the base of the sidespray and put on washer and fitting
nut.
Turn on the water supplies and flush hot and cold water for 1
minute while rotating the handle.
Connect and tighten the supply hoses.

Care and Cleaning:

Regularly clean the faucet with a mild soap solution and water.
Avoid using harsh chemicals or abrasives that may damage the
finish.

FAQ:

Q: Can I use this faucet with a single handle

configuration?

A: No, this faucet is designed for a two-handle configuration
only.

Q: How often should I clean the faucet?

A: It is recommended to clean the faucet regularly with a mild
soap solution to maintain its appearance.

“`

1 LY GELE2 ONL 3 GELE ONLY Applicable faucets (including but not limited)

INSTALLATION
Prior to installation: Shut off water supply. Remove old faucet.
Clean sink/countertop surface in preparation for new faucet.

Apply some plumbers putty or other suitable sealant to the bottom edge of undercover.

Allign and press into place.

Two Handle Faucet
Insert the faucet through sink.

ONLY GELE ONLY GELE4 ONGELE ONL5Y GELE ONLY6LE ONLY GELE TOOLS YOU WILL NEED

Screw the nut onto shrank,leaving approximately 0.12″(3mm) between the ring and the sink.

Tighten fitting nuts with adjustable wrench. Do not over tighten!

If sidespray not included,connect and tighten hoses with hot and cold water supply. If included. insert the sidespray, proceed to step 7-11.

GELE ONLY E ONLY GE Adjustablewrench

phillips screwdrive

Hex Wrench

ONLY Y GEL TwoMaleSupply

pipe tape

Silicone sealant/Putty

GELE LE ONL Right of product modification such as dimension without notice is reserved.

LE ONL NLY 7 Insert the base of sidespray. GELE ONLY GELE ONLYLEGEONLY GELE ONLY GELNELYO GELE 8 Putonwasherandfittingnut.

10 Turn on the water supplies.While rotating the handle, flush the hot and cold water for 1 minute.
11 Connect and tighten the supply hoses.

Two Handle Faucet
12 Care and Cleaning
For best results,keep the following in mind when caring for your product: ·Use a mild detergent such as liquid dishwashing soap and warm water for cleaning. Do not use abrasive cleaners that may scratch or dull the surface. ·Carefully read the cleaner product label to ensure the cleaner is safe for use on the material. ·Always test your cleaning solution on an inconspicuous area before applying to the entire surface. ·Do not allow cleaners to sit or soak on the surface. ·Wipe surfaces clean and rinse completely with water immediately after cleaner application.Rinse and dry any overspray that lands on nearby surfaces.

ONLY ONLY GE GELE O 9 Tightenit. GELE E ONLY C
E ONLY LY GEL C GEL LE ON Right of product modification such as dimension without notice is reserved.