Netatmo N3A-NAS01 Weather Station Wireless Outdoor Sensor User Manual
- June 4, 2024
- Netatmo
Table of Contents
Safety warnings, compliance, and declaration of conformity
Safety Warnings
This device is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.
Before inserting the batteries, check that the contacts in the device and on
the batteries are clean, and clean them if necessary. Note the polarity (+/-)
when inserting the batteries. Do not throw the batteries into a fire, short-
circuit it or dismantle it. Keep children away from batteries. Seek medical
attention immediately if a battery is swallowed.
Declaration of Conformity
Hereby, NETATMO, declares that the radio equipment type NAS01 is in compliance with Directive 2014/53/EU as well as the RoHS Directive 2011/65/EU and its amendment 2015/863/EU. Hereby, NETATMO, declares that the radio equipment type NDB01 is in compliance with Radio Equipment Regulations 2017 and The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 The full text of the EU and UKCA declaration of conformity is available at the fol- lowing internet address:
www.netatmo.com/declaration/nas
Netatmo SAS – 73/77 rue de Sèvres – 92100 Boulogne Billancourt
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
inter- ference will not occur in a particular installation.
lf this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device NDB01 complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth for the
general population (uncontrolled exposure). This device must be installed to
provide a separation distance of at least 20cm from all persons and must not
be collocated or operating in conjunction with any other antenna or
transmitter.
Caution
This equipment may not be modified, altered, or changed in any way without
signed written permission from NETATMO. Unauthorized modification may void the
equipment
authorization from the FCC and will void the NETATMO warranty.
Canadian Compliance Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device. Under
Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This device complies with Industry Canada RF
radiation exposure limits set forth for the general population (uncontrolled
exposure). This device must be installed to provide a separation distance of
at least 20cm from all persons and must not be collocated or operating in
conjunction with any other antenna or transmitter.
Wireless connectivity
PMN: Netatmo Alarm Sensor
| CE marking is the manufacturer’s declaration that the product meets the
requirements of the applicable EC directives.
---|---
| The product complies with the requirements of the relevant ACMA Standards.
| WEEE symbol designates safe and responsible collection, recycling, and
recovery procedures for all types of electronic waste.
| The product complies with the Technical Regulations Conformity Certification
of Specified Radio Equipment.
M/N:| Model Number
FCC ID:| The product complies with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules (USA).
IC:| The product complies with Industry Canada license-exempt RSS
standard(s).
gXXXXXX| Serial number
| UKCA marking is the manufacturer’s declaration that the product meets the
requirements of the applicable UK directives (Due to Brexit).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>