SEALEY 9140L Foam Latex Gloves Instruction Manual
- May 15, 2024
- SEALEY
Table of Contents
FOAM LATEX GRIPPA GLOVES
MODEL NO: 9140L, 9140XL
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
REFER TO INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
1. INTRODUCTION
Latex coating gives superior grip in wet and dry conditions. Lightweight design for superior dexterity. CE Marked and conforms to BS EN 388:2016 2-1-2-1-X.
Sizes: Large, Extra-Large
Notified Body: 0075
Type Examination Certificate Number: 0075/1022/162/07/19/2211
Carried Out By: CTC
2. SAFETY
Users should be warned that gloves should not be worn when there is a
risk of entanglement by moving parts of machines.
This model does not contain any substances at levels that are known to,
or suspected to, adversely affect user hygiene or health.
The protection against risks or hazards which are not mentioned in this
document is not warranted.
The levels of performance mentioned are only valid for the palm of the
glove.
These levels of performance are obtained from the tests done according
to the conditions defined by the applicable standards.
This glove shall not be in contact with fire.
Before use, the glove shall be visually controlled. In case of
deterioration the gloves must be scrapped (abrasion, cut, tear, …).
For gloves with two or more layers of material, the performance levels
are warranted only for the whole glove.
**** For gloves with two or more layers the overall classification does not
necessarily reflect the performance of the outermost layer.
3. APPLICABLE STANDARDS
Mechanical Hazard EN 388 : 2016
2121X
| Abrasion Resistance| 2| (on 4 maxi) | ‘X’ indicates that the glove has not
been submitted to the test or the test method appears not to be suitable for
the glove design or material.
---|---|---|---|---
Blade Cut Resistance| 1| (on 5 maxi)
Tear Resistance| 2| (on 4 maxi)
Puncture Resistance| 1| (on 4 maxi)
Cut Resistance Method (EN ISO 13997) | X| (A to F)
Impact Protection| –|
4. MAINTENANCE
4.1. STORAGE
Store the gloves in their original packaging.
Store the gloves in normal temperature and humidity conditions.
**** Store the gloves in clean, covered and ventilated premises.
4.2. MAINTENANCE
The gloves should be inspected before each use, and replaced if damaged.
When stored in appropriate conditions, performance of this product will
not be significantly reduced.
This document has been drawn up according to Regulation (EU) 2016/425 as amended to apply to GB for Personal Protective Equipment. The declaration of conformity can be accessed atwww.sealey.co.uk.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
EU | Sealey EU Ltd, Farney Street, Carrickmacross, Co. Monaghan, A81 PK68
Ireland
UK | Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds,
Suffolk. IP32 7AR
01284 757500sales@sealey.co.uk www.sealey.co.uk
© Jack Sealey Limited Original Language Version
9140L, 9140XL Issue 1 06/10/23