AMPIRE CPS090 Mirror Monitor Owner’s Manual

AMPIRE CPS090 Mirror Monitor

Precautions

• Pay utmost attention if you install the monitor into the driver’s compartment.
• Use only in cars with a 12 or 24 Volt negative ground.
• Before wiring, disconnect the cable from the negative battery terminal to avoid short circuits or electrical shocks. Make the correct connections.
• Do not damage pipe or wiring when drilling holes.
• Arrange the wiring so it is not crimped or pinched by a sharp metal edge.
• Do not install the monitor in locations which might hinder vehicle operations and do not install in locations with any moisture. Use the installation materials provided with the monitor.
• Do not use bolts or nuts in the brake, airbags or other safety relevant systems to make ground connections.
• Attention! This monitor is developed for motor vehicle use only.
• WARNING: DO NOT WATCH MOVIES WHILE DRIVING TO AVOID DANGER!

Environmental Reference

• Old electronic devices do not belong in the garbage can.
• If you later want to dispose of this device, remove all cables and batteries and dispose of them separately at a recycling facility in your area.
• Alternatively, you can return this device to Ampire for disposal.
• The packaging is recyclable. Dispose of the packaging in a designated collection system.

Environmental instructions and information on the disposal of electrical and electronic equipment including batteries (applicable to countries that have adopted a separate collection system)

If you want to dispose of this product, do not dispose of it with your normal household waste. There is a separate collection system for used electronic equipment in accordance with legal requirements that require appropriate treatment, recovery and recycling. Contact your local authority for details on finding a recycling facility in your area. Proper recycling and disposal helps to conserve resources and prevent harmful effects on our health and the environment.

Hereby Ampire Electronics GmbH & Co.KG declares that the monitor CPM1O1 complies with the directives 2O14/3O/EU, 2O14/35/EU, 2O14/53/EU and 2O11/65/EU. The full text of the EU Declaration of Conformity in German language is available at the following Internet address: https://ce.ampire.de

Scope of Delivery

• Mirror Monitor
  

• Mounting Rubbers

• Power Cable, 320cm
  

• RVC Connection Cable, 700cm
  

• AHO Reverse

• Camera 3,5 mm Jack Cable, 120cm
  

Connection

HOME Menu

When you switch on the device, you are automatically taken to the HOME menu. All basic settings and the coupling of Apple CarPlay and Android Auto can be made from here. You also have access to the dash cam and its recordings from here.

1. Time and day of the week
2. ON/OFF button. Tapping turns the screen dark, but the device stays on.
3. Switch to Apple CarPlay. See page 27.
4. Switch to Android Auto. See page 28.
5. Switching to the driving monitor. See page 30.
6. ON/OFF switch on the underside of the housing. A short press turns the screen dark, a long press turns the device off.
7. Audio output menu. See page 31.
8. Setting. Basic settings can be made here. See page 24.
9. Volume. The output volume can be set here. See page 23.
10. Brightness. The screen brightness can be adjusted here. See page 23.

Brightness and Volume

Brightness:
Tap the brightness icon and then use the on-screen slider to adjust the brightness. The brightness setting disappears automatically six seconds after the setting is done.

Volume:
Tap the volume icon and then use the onscreen slider to adjust the volume of the built-in speaker. The volume setting disappears automatically six seconds after the setting is done.

Settings

Tap the Setting icon to bring up the menu.

Set the video resolution of the front and rear cameras to 720P+720P or 1080P+ 1080P. Both cameras always have the same value.

Set the length of the dashcam recording segments (1, 3 minutes or 5 minutes).

Switch the image mirroring of the rear camera on or off here (On/Off)

The activated screen saver automatically deactivates the monitor after 10, 30 or 60 seconds.

In parking mode, the dash cam starts a time-lapse recording as soon as movement is detected with the ignition switched off. Parking mode can be activated for 12 or 24 hours. After the set time, the parking mode turns off automatically.
ATTENTION, when the parking mode is switched on, the power consumption is 290mA! The CPS090 has an undervoltage protection that automatically switches off the device at 11.8V and protects the vehicle battery.

Turn on voice control and control the camera display with voice commands.

Choose the driving position left or right

Guidelines Calibration

1. Park the vehicle backwards in the middle of a marked parking space.
2. Use the arrow buttons ∧∨ on the left edge of the screen to set the height of the image section that you want to see when reversing.
3. Align the guides with the parking lot markers.
4. Tap on “Confirm” to save the settings.
   

Set the desired language here. You can choose between DE, EN, CN, RU, ES, FR, IT, PT, JPN and KOR.

Set the time and date here. Then tap on “Confirm” to apply the settings.

The microSD card can be formatted here. This may be necessary, for example, when inserting the microSD card for the first time.

To reset the CPS090 to factory default, tap on this symbol and then on “Confirm”. Resetting will erase all settings.

The current firmware version that is saved on the device is displayed here.

Toolbars

The icons on the left and right toolbars change depending on the selected operating mode or the menu you are in.

1. Time and day of the week

2. ON/OFF button. Tapping turns the screen dark, but the device stays on.

3. Switching to the CarPlay / Android Auto interface of the connected smartphone.

4. HOME button. Tapping the HOME button always takes you to the HOME menu.

5. Switch to the camera display.
   

6. Brightness. The screen brightness can be adjusted here. See page 23.

7. If this icon is displayed, the audio output via the internal speaker has been selected.

8. If this symbol is displayed, audio output via Bluetooth audio streaming has been selected.

9. If this symbol is displayed, the audio output via the FM transmitter has been selected.

10. If this symbol is displayed, the audio output via the AUX output has been selected.
    

CarPlay

The first pairing: Turn on WiFi and Bluetooth in your iPhone. Then tap Apple CarPlay on the CPS090 main menu to open the CarPlay menu.
Now connect your iPhone to the T86-xxxxxx device via Bluetooth and confirm the CarPlay dialog on the iPhone display. ATTENTION: Your iPhone must not be connected to any other WiFi network for CarPlay!

Full Screen Mode/ Half Screen Mode: Before pairing your iPhone, you can choose whether you want to use CarPlay in full screen or half screen mode. In half screen mode, CarPlay is displayed on the left side of the monitor and a camera image is displayed on the right side of the monitor. This setting cannot be changed during operation. To change, turn off Wi-Fi on your iPhone, go to the CarPlay menu, and select the desired option, Full Screen or Half Screen Mode. Then turn WiFi back on in your iPhone.
Note: In half screen mode, you can switch between the two cameras by tapping on the camera image at the right.

Android Auto

The first pairing: Turn on WiFi and Bluetooth in your smartphone. Then tap Android Auto on the CPS090 main menu to open the Android Auto menu. Now connect your smartphone to the T86-xxxxxx device via Bluetooth. ATTENTION: Your smartphone must not be connected to any other WiFi network for Android Auto!

Full screen mode/ half screen mode: Unlike Apple CarPlay, Android Auto does not have full screen mode for the CPM090 and the display is always in half screen mode. This is due to the fact that Android Auto has a fixed icon structure and mandatory display requirements. Only four icons are displayed next to each other and the user must be able to see at least two lines on the display. This requirement cannot be met in full screen mode, which is why only half-screen mode is available to the CPS090 for Android Auto.

WI Fl-Video

You can also save and view the dash cam recordings locally on your smartphone. From the HOME menu, tap Apple CarPlay or Android Auto depending on the smartphone you are using, then select WIFI Video. Scan the QR code to download the necessary Viidure app.

According to the APP prompt, connect to the monitor’s local WiFi. The WLAN name is T86-xxxxxx, the password is 12345678. Now you have access to all stored videos from your smartphone, which you can play on the smartphone and save locally.

ATTENTION!
The simultaneous use of Apple CarPlay or Android Auto is disabled while connected to WIFI video not possible!

Driving Monitoring

The driving monitor is a dual dash cam that films front and rear in AHO and records in HD. At the same time, the cameras can be displayed on the monitor, either in full screen (camera in front or behind) or simultaneously in split screen.

Menu bar
The menu bar will automatically hide after 6 seconds and reappear by tapping the screen.

Menu bar

| Star/stop manual recording
---|---
| Manually protect the recording from being overwritten
| NmN Photo capture (screenshot)
| Switches to the HOME menu

| Switches to Apple CarPlay or Android Auto
---|---
| Turn microphone on/off for recording
| Switches to video playback

Audio Output

In this menu you can select the type of audio output.

Speaker
The audio output takes place via the internal loudspeaker.
Tapping the speaker icon opens the volume setting.

Bluetooth for CarPlay
The audio output takes place via Bluetooth A2DP. Connect your smartphone to your car radio via Bluetooth.

FM transmitter
Set a frequency for the CPS090 to transmit on. The FM transmitter only works when using the original power cable.

Aux
The audio output takes place via the AUX output.

Reverse Camera

As soon as reverse gear is engaged, the CPS090 switches to the rear camera with the image section that was previously set in the guide line calibration (see page 25) and shows guide lines as a maneuvering aid. The prerequisite for this is that the red cable “Reversing signal + 12V” (see page 21 “Connection”) has been connected to the 12V cable of the reversing light. When reverse gear is disengaged again, the CPS090 switches back to the previous view with a 3 second delay.

Note: The running front and rear camera recordings will not be interrupted while reversing.

Technical Specifications

Transmit Power
BT| <10mW EIRP
FM| <50mW ERP
WiFi 5GHz| 200mW EIRP (5, 15-5,25GHz) <1W EIRP (5,47-5,57GHz)

Since its founding in 1987 Ampire Electronics has only one goal, to provide the best possible Caralarm-, Carhifi- and Multimedia products, which are available on the international market.

All manufacturing facilities and suppliers are certified according to ISO 9001 and QS-9000. Ampire quality products are sold worldwide.

An Ampire customer service is available in many countries.
For more information about distributors in your territory please call: + 49-2181-81955-0.

We are focused on future oriented development of user friendly products. The outstanding high quality standards, functionalities and designs of our products are unique in the market. “German Development’ is taken literally in AMPIRE.

Customers Support

Scan for the most recent operation manual

© 2023 AMPIRE ELECTRONICS. All rights reserved. Reproduction in whole or in part without written permission.

Langwadener StraBe 60
D-41516 Grevenbroich
Email: info@ampire.de

Technischer Support:
Tel.: 02181-81955-0
Email: support@ampire.de
www.ampire.de

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>